Sears 358.79828 manual Hardware Contents

Page 5

=

HARDWARE CONTENTS

Hardware shown full size

Parts bag contents not shown full size

i

						Locking Pin
							Spark
(4) Screws							Arrestor	Screen
(4) Screws	@
		(2) Mounting	Blade Nut/
		(2) Mounting	Spark Rug
		Screws	Spark Rug			J	Carburetor
		Screws		Wrench
(2) Lock				Wrench
(2) Lock	(2) Nuts					Hex Key	Screwdriver"
Washers						Hex Key	Screwdriver"


			r	i ¸ r	i --r .
				i	1	i	i	I `•. ._• ii1.
		Parts packed separately in carton

Line Limiter

3.2 oz. Oil

Metal Blade Shield

Plastic Line Xrimmer Shield with Lthe Umiter Hardware

Brush Tri-Blade	Shield Support	Dual Une "Cutting Head
	Plate

Operator's Manual

Shoulder Harness

Handlebar

eeLS REQUIRED FOR ASSEMBLY

Torque Wrench-reference torque values are provided throughout this manual for tightening hardware.

Phillips Screwdriver

8 mm Wrench

Provided with your Bmshwacker: Hex Key

Blade Nut/Spark Plug Wrench Locking Pin

O

	Blade Transport/
Sapling Saw Blade	Storage Cover

TO REMOVE BRUSHWACKER FROM CARTON

•Remove loose parts included with Brushwacker.

•Remove the loose plastic parts bag from the carton.

•Remove all packing material.

;, Check carton thoroughly for additional loose parts.

-5-

l

Image 5

Contents Page Page Leg Guards EyeBoots Protection Hazard Zone Safety RulesManual LabelsAir gap.010-.014 Maintenance AgreementProduct Specifications Hardware Contents Spark Arrestor Screen Assembly See Fig AssemblyThrottle Handle Assembly See Fig Uerore installing me nanolecar,you-musLunmreadtheIii Installing UNE LIMI3R-ONTO Cutting Line Head ConfigurationInstalling Dual MNE Head Line Trimmer ShieldIstalung the Metal Blade Shield Rush TRI-BLADE ConfigurationREINSTALLATiON PRE-INSTALLATION SAW Blade ConfigurationInstalung the SAW Blade See ,13Starter Rope SPARKPLUGv \ OperationInside ShieldStopping Your Engine Blade TRANSPORT/STORAGE Cover Turn the engine Off before adjusting handlebarShoulder Harness and hook on the unit3LADE Safety OPERATION-SAFETYSafety Coasting BLADE- ThebladecontinuestoWhen does Blade Thrust OCCUR? Blade SafetyWhat Causes Blade THRUST? 787Blade Brush TRI-BLADESapling SAW Blade Blade Continues to Spin After the Engine is Turned OFRPerator Safety Line Trimmer SafetyUnit S .FEW Nttclcnne%/hemnagngoatesrapstasPerating ! USE Tips RningTg , 23 , 24 , 25 Nique increases line wearCycle OIL Fuel Mixture ChartFuel Stabilizer Gasoline and OIL MixtureStarting a Warm Engine That has not Topping Your EngineStarting a Flooded Engine =.FORE Starting the EngineCustomer Responsibi Lities Maintenance ScheduleGeneral Recommendations Before Each USECleaning the Spark Arrestor Screen Inspect Muffler Spark Arrestor Screen if InstalledIeck for Loose FASTENERS/PARTS ECK Gear BOX LubricationDual Line Replacement Service and AdjustmentsInstalling Spool with Line Already Wound ,33,34,35Brush TRI-BLADE Sharpening Fig Ilade SharpeningSAW Blade Sharpening Fig Manner to Maintain a Balanced BladeAdjusting Procedure Carburetor AdjustmentsIdle Speed Adjustment High Speed Mixture AdjustmentFuel container StorageShooting Chart Trouble Shooting PointsSymptom Cause Remedy TroubleRepair Parts 503-797501 4143Sears Brushwacker Model Repair PARTs Plastic Shield Incl. Line Limlter Scrirt.ioaTable of Contents Lowing Information If YOU Need Repair Service or PartsPart Number 101-870491