Sears 358.79828 Cutting Line Head Configuration, Installing UNE LIMI3R-ONTO, Line Trimmer Shield

ASSEMBLY

CUTTING LINE HEAD

CONFIGURATION

Brush and Saw Blade ConflguraUonsfollow this section.

& WARNING:

THE LINE LIMITER IS SHARP AND CAN CUT YOU. BE SURE TO WEAR GLOVES WHILE WORKING WITH THE LINE UMITER.

INSTALLING THE PLASTIC LINE TRIMMER SHIELD (See Fig. 5 )

•Place the plastic line trimmershieldon the gearbox, and align the four screw holes as illustmfed.

•Place the shield support plate under the shield and align the four screw holes.

•Secure the plasticline trimmershieldusing the 4 mount- ing screws provided in the loose parts bag.

•Tighten evenly (70 Ib-in mimimum) using the hex key

	THE PLASTIC UNE TRIMMER SHIELD					provided in the	loose parts bag.
	MUST BE PROPERLY			INSTALLED FOR ALL		Arbor	_ -F_
	LINE TRIMMER USAGE. THE PLASTIC
	UNE TRIMMER SHIELD PROVIDES PAR-
	TIAL PROTECTION FROM THE RISK OF
	THROWN OBJECTS TO THE OPERATOR					Driyin_] /t!/i_		_J_	Plast_Une
	AND OTHERS,
					PI.:ASTIC_?,__;-.....Di 2! .			/	T,mme,.
INSTALLING		UNE :LIMI3_R_-ONTO
									Shield
LINE TRIMMER SHIELD			(See Fig.4)			Shield Support	__,,	_.
						Plate
• Pos_on line limiteronto the plastic line trimmershield.							Figure	5
IMPORTANT:		ALTHOUGH SCREW HOLES EXIST ON				INSTALLING	THE DUAL	MNE	HEAD
BOTH EDGES OF THE PLASTIC LINE TRIMMER						(See Fig. 6 & 7 )
SHIELD, MAKE SURE YOU INSTALL THE LINE UMo
rrER ON THE SIDE SHOWN			IN THE ILLUSTRATION.			Before installing the dual line head, make sure the driving
• Secure line limiter to the plastic line trimmershield using						diskis in place on the gear box,
						• Rotate the hex fastener on the dual line head counter-
the two mounting screws, lock washers, and nuts found
						clockwise onto the arbor shaft.
in the loose parts bag using a phillips screwdriver and
						•Tum the arbor shaftto align one of the three holes in the
8ram wrench.
• Tighten securely.						ddving diskw_ththe hole in the gearbox.
						• Insert the locking pin through the gearbox and driving
	Nuts_		Une Umiter .			disk. This will lock the driving disk, and prevent the arbor
						shaft from turning while you tighten the dual line head.
	--,-,,,,. . /_'___,_,			Line Limiter parts are		• While holdingthe Iockingpinin place, tighten the dual line
						head onto the arbor shaft counterclockwise using the
'	,,,=_,,_'"::_':rs			located in a bag at-
						blade nut/spark plug wrench(15-20 Ib-ft);
		"///'_		tashed	to the Plastic	Should the arbor shaft continue to turnwhile you are tight-
		._--	_l	Line Trimmer Shield.
						ening the dualline head, re-positionthe/ockingpinthrough., ,,..
						the gearbox and driving disk.
Plastic Line _		\y_-_-		Screws			Locking Pin	Arbor Shaft
FdmmerShield						......Plastic Line
		Figure 4
						Trimmer Shield			Disk

PRE-INSTALLATION

If the metal blade shield is installed on the unit, you must first remove the-nut,supportflange, blade, and metalb/ade shield as follows before installing the plastic fine trimmer shieldand duat line cutdng head.

•Clip blade transport/storage cover over the blade. (Refer to figure 9)

•To remove blade (Sea Figures 11 or 14), place lockingpin through the gearbox and driving disk to preventthe arbor shaft from turning and remove the blade nut by turning clockwise with blade nut/spark plug wrench. Save parts removed for future use.

•Remove 4 screws with hex key holding the metal blade shield. Save these 4 screws for installationofthe plastic line trimmer shield.

Dual	Hex Fastener
	(underneath)
Figure	6
Lockin! Pir_ual	Cutting Head
Plastic Line
Trimmer Shield _'<	II Counterclockwis_

Blade Nut/Sl_ irk Plug Remove Clockwis_ Wrench

Figure 7

-8-