Troy-Bilt 772C0748 manual OFF Engaging the PTO, Using the Lift Lever, Mowing, Mulching

Page 17

Front View

Pull Out

Push In

OFF

ON

Figure 9

ENGAGING THE PTO

Engaging the PTO transfers power to the cutting deck or other (separately available) attachments. To engage the PTO, proceed as follows:

Move the throttle control lever to the FAST (rabbit) position.

Models with manual PTO

Grasp the PTO lever and pivot it all the way forward into the engaged (ON) position.

Models with electric PTO

Pull the PTO knob outward into the engaged (ON) position. See Figure 9.

NOTE: Keep the throttle lever in the FAST (rabbit) position for the most efficient use of the cutting deck or other (separately available) attachments.

IMPORTANT: The engine or electric PTO clutch will automatically shut off if the PTO is engaged with the drive pedal in position for reverse travel. Refer to SAFETY INTERLOCK SWITCHES earlier in this section.

To disengage the PTO , push the PTO knob in, or move the PTO lever to the “Blade Stop” position. This will cut off power to deck or other attachments.

USING THE LIFT LEVER

To raise the cutting deck, move the lift lever to the left, then place it in the notch best suited for your application. Refer to SETTING THE CUTTING HEIGHT earlier in this section.

MOWING

WARNING: To help avoid blade contact or a thrown object injury, keep bystanders, helpers, children and pets at least 75 feet from the machine while it is in operation. Stop machine if anyone enters the area.

This tractor is equipped with a high quality cutting deck. The following information will be helpful when using the cutting deck with your tractor.

Do not mow at high ground speed, especially if a mulch kit or grass collector is installed.

WARNING: Plan your mowing pattern to avoid discharge of materials toward roads, sidewalks, bystanders and the like. Also, avoid discharging material against a wall or obstruction which may cause discharged material to ricochet back toward the operator.

For best results it is recommended that the first two laps be cut with the discharge thrown towards the center. After the first two laps, reverse the direction to throw the discharge to the outside for the balance of cutting. This will give a better appearance to the lawn.

Do not cut the grass too short. Short grass invites weed growth and yellows quickly in dry weather.

Mowing should always be done with the engine at full throttle.

Under heavier conditions it may be necessary to go back over the cut area a second time to get a clean cut.

Do NOT attempt to mow heavy brush and weeds and extremely tall grass. Your tractor is designed to mow lawns, NOT clear brush.

Keep the blades sharp and replace the blades when worn. Refer to the SERVICE section of this manual for proper blade sharpening instructions.

MULCHING

Tractors come equipped with a mulch kit which incorporates special blades, already standard on your tractor, in a process of recirculating grass clippings repeatedly beneath the cutting deck. The ultra-fine clippings are then forced back into the lawn where they act as a natural fertilizer. Observe the following recommendations for the best results when mulching.

Never attempt to mulch if the lawn is damp. Wet grass tends to stick to the underside of the cutting deck preventing proper mulching of the clippings.

Do NOT attempt to mulch more than 1/3 the total height of the grass or approximately 1-1/2 inches. Doing so will cause the clippings to clump up beneath the deck and not be mulched effectively.

Maintain a slow ground speed to allow the grass clippings more time to effectively be mulched.

Always position the throttle control lever in the FAST (rabbit) position and allow it to remain there while mowing. Failing to keep the engine at full throttle places strain on the tractor’s engine and does not allow the blades to properly mulch grass.

NOTE: It is not necessary to remove the discharge chute to operate the mower with the mulch kit installed.

The mulch kit is packed separately (with an instruction sheet) within the tractor’s crate. Observe the instruc- tions included with the mulch kit for the best results when mulching.

17

Image 17
Contents Operator’s Manual Table of Contents General Operation Important Safe Operation PracticesChildren Slope OperationDo not Towing ServiceModel Description Attachments & AccessoriesSlope Gauge Tractor SET-UP Attaching the Battery CablesAttaching the Steering Wheel Attaching the SeatGAS and OIL FILL-UP Installing the PTO/DECK BeltAttaching the Cutting Deck 54 Deck Idler Pulley Controls Throttle Control Lever Ignition SwitchChoke Control Brake PedalElectric PTO Power TAKE-OFF Knob Systems Indicator Monitor / Hour MeterPTO Power TAKE-OFF Lever Seat Adjustment LeverReverse Caution Mode Safety Interlock SwitchesOperating Your Garden Tractor Cruise Control ButtonStarting the Engine Setting the Cutting HeightTo use the Reverse Caution Mode Stopping the Engine Setting the Cruise ControlEngaging the Parking Brake Driving the TractorOFF Engaging the PTO Using the Lift LeverMowing MulchingLeveling the Deck Making AdjustmentsHeadlights Seat Adjustment Deck Roller Height AdjustmentParking Brake Adjustment Steering AdjustmentCleaning the Engine and Deck MaintenanceEngine LubricationChanging Engine OIL Read and follow instructions carefullyBattery ServiceTires Cutting BladesCharging Battery FailuresJump Starting FusesDeck / PTO Belt Changing the Deck Belt & PTO BeltUpper Drive Belt Changing the Transmission Drive BeltsLower Drive Belt OFF-SEASON StorageTrouble Possible Causes Corrective Action Troubleshooting

772C0748 specifications

The Troy-Bilt 772C0748 is a powerful and versatile rotary lawn mower designed for maintaining a pristine lawn with ease. Known for its durability and efficiency, this model is tailored for homeowners who seek a reliable solution for their mowing needs.

One of the standout features of the Troy-Bilt 772C0748 is its strong engine. Equipped with a robust 159cc engine, this mower delivers impressive cutting performance and allows for efficient operation over a variety of terrains. The engine is designed for easy starting, minimizing the hassle often associated with lawn maintenance.

The mower boasts a 21-inch cutting deck, which offers a balance between maneuverability and cutting width. This size is ideal for residential lawns, allowing users to navigate through narrow paths and tight corners with ease. The cutting deck is made from durable materials, ensuring longevity and resilience against the rigors of outdoor use.

Another notable characteristic of the Troy-Bilt 772C0748 is its adjustable cutting height feature. With six different height settings, users can achieve their desired lawn length with precision. This flexibility is essential for accommodating different grass types and seasonal growth patterns, ensuring a well-maintained lawn throughout the year.

The mower’s design also prioritizes user comfort. It features an ergonomic handle that reduces strain during operation, allowing for longer mowing sessions without discomfort. The handle is also foldable, which not only saves storage space but also enhances portability.

In terms of technology, the Troy-Bilt 772C0748 incorporates a reliable grass collection system. The rear bagging capabilities allow for efficient collection of clippings, which can be easily emptied, promoting a cleaner mowing experience. The mower also has side discharge capabilities, providing options for lawn maintenance according to user preferences.

Overall, the Troy-Bilt 772C0748 combines power, efficiency, and user-friendly features, making it an excellent choice for homeowners looking to maintain their lawns effortlessly. Its durable construction, innovative technology, and thoughtful design characteristics position it as a standout option in the competitive lawn mower market. Whether tackling small patches or larger areas, the Troy-Bilt 772C0748 promises to deliver consistent performance and a beautiful, well-groomed lawn.