Troy-Bilt 772C0748 Lubrication, Changing Engine OIL, Read and follow instructions carefully

Page 21

7.Engage the tractor’s PTO.

8.Remain in the operator’s position with the cutting deck engaged for a minimum of two minutes, allowing the underside of the cutting deck to throughly rinse.

9.Disengage the tractor’s PTO.

10.Turn the ignition key to the STOP position to turn the tractor’s engine off.

11.Turn the water off and detach the hose coupler from the water port on your decks surface. Repeat step 4-11 on the opposite side of the cutting deck.

ENGINE

Refer to the separate engine manual for engine maintenance instructions.

Check engine oil level before each use as instructed in the separate engine manual packed with your unit.

Read and follow instructions carefully.

CHANGING ENGINE OIL

Oil Fill Cap

Protective Cap

 

 

Oil Drain Hose

 

 

Oil Drain Valve

 

 

Oil Fill Tube

Oil Drain Port

 

 

NOTE: Single-cylinder engine shown.

Valve location will vary with engine style.

Figure 15

NOTE: Depending on the engine model found on your tractor, it may be necessary to remove the tractor’s side panel in order to replace the oil filter (if so equipped).

•Unscrew oil fill cap and remove dipstick from the oil fill tube. See Figure 15.

•Pop open the protective cap on the end of the oil drain valve to expose the oil drain port. See Figure 15.

•Push oil drain hose (packed with unit) onto the oil drain port. Route the opposite end of the hose into an appropriate oil collection container with a capacity great enough to collect the used oil.

•Push the oil drain valve in slightly, then rotate counterclockwise and pull outward to begin draining oil. See Figure 15.

•Service the oil filter (if so equipped) as instructed in the separate engine manual packed with your unit.

Perform the above steps in the opposite order after oil has finished draining.

•Refill the engine with new motor oil.

IMPORTANT: Refill the engine with the proper capacity and weight of motor oil as instructed in the separate engine manual.

Service air cleaner every 25 hours under normal conditions. Clean every few hours under extremely dusty condition. To service the air cleaner, refer to the separate engine manual packed with your unit.

The spark plug(s) should be cleaned and the gap reset once a season. Spark plug replacement is recommended at the start of each mowing season; check engine manual for correct plug type and gap specifications.

SECTION 9: LUBRICATION

WARNING: Before lubricating, repairing, or inspecting, always disengage PTO, move shift lever into neutral position, set parking brake, stop engine and remove key to prevent unintended starting.

Engine

Lubricate the engine with motor oil as instructed in the Engine Owner’s Manual packed with your unit.

Pivot Points & Linkage

Lubricate all the pivot points on the drive system, parking brake and lift linkage at least once a season with light oil.

Front Wheels

Each of the front wheel axles is equipped with a grease fitting. Lubricate with a grease gun after every 25 hours of tractor operation.

Rear Wheels

The rear wheels should be removed from the axles once a season. Lubricate the axles and the rims well with an all-purpose grease before re-installing them.

21

Page 20 Page 22
Image 21
Page 20 Page 22
Contents Operator’s Manual Table of Contents General Operation Important Safe Operation PracticesSlope Operation Do notChildren Towing ServiceModel Description Attachments & AccessoriesSlope Gauge Tractor SET-UP Attaching the Battery CablesAttaching the Steering Wheel Attaching the SeatInstalling the PTO/DECK Belt Attaching the Cutting Deck 54 DeckGAS and OIL FILL-UP Idler Pulley Controls Throttle Control Lever Ignition SwitchChoke Control Brake PedalElectric PTO Power TAKE-OFF Knob Systems Indicator Monitor / Hour MeterPTO Power TAKE-OFF Lever Seat Adjustment LeverReverse Caution Mode Safety Interlock SwitchesOperating Your Garden Tractor Cruise Control ButtonSetting the Cutting Height To use the Reverse Caution ModeStarting the Engine Stopping the Engine Setting the Cruise ControlEngaging the Parking Brake Driving the TractorOFF Engaging the PTO Using the Lift LeverMowing MulchingMaking Adjustments HeadlightsLeveling the Deck Seat Adjustment Deck Roller Height AdjustmentParking Brake Adjustment Steering AdjustmentCleaning the Engine and Deck MaintenanceEngine LubricationChanging Engine OIL Read and follow instructions carefullyBattery ServiceTires Cutting BladesCharging Battery FailuresJump Starting FusesDeck / PTO Belt Changing the Deck Belt & PTO BeltUpper Drive Belt Changing the Transmission Drive BeltsLower Drive Belt OFF-SEASON StorageTrouble Possible Causes Corrective Action Troubleshooting

772C0748 specifications

The Troy-Bilt 772C0748 is a powerful and versatile rotary lawn mower designed for maintaining a pristine lawn with ease. Known for its durability and efficiency, this model is tailored for homeowners who seek a reliable solution for their mowing needs.

One of the standout features of the Troy-Bilt 772C0748 is its strong engine. Equipped with a robust 159cc engine, this mower delivers impressive cutting performance and allows for efficient operation over a variety of terrains. The engine is designed for easy starting, minimizing the hassle often associated with lawn maintenance.

The mower boasts a 21-inch cutting deck, which offers a balance between maneuverability and cutting width. This size is ideal for residential lawns, allowing users to navigate through narrow paths and tight corners with ease. The cutting deck is made from durable materials, ensuring longevity and resilience against the rigors of outdoor use.

Another notable characteristic of the Troy-Bilt 772C0748 is its adjustable cutting height feature. With six different height settings, users can achieve their desired lawn length with precision. This flexibility is essential for accommodating different grass types and seasonal growth patterns, ensuring a well-maintained lawn throughout the year.

The mower’s design also prioritizes user comfort. It features an ergonomic handle that reduces strain during operation, allowing for longer mowing sessions without discomfort. The handle is also foldable, which not only saves storage space but also enhances portability.

In terms of technology, the Troy-Bilt 772C0748 incorporates a reliable grass collection system. The rear bagging capabilities allow for efficient collection of clippings, which can be easily emptied, promoting a cleaner mowing experience. The mower also has side discharge capabilities, providing options for lawn maintenance according to user preferences.

Overall, the Troy-Bilt 772C0748 combines power, efficiency, and user-friendly features, making it an excellent choice for homeowners looking to maintain their lawns effortlessly. Its durable construction, innovative technology, and thoughtful design characteristics position it as a standout option in the competitive lawn mower market. Whether tackling small patches or larger areas, the Troy-Bilt 772C0748 promises to deliver consistent performance and a beautiful, well-groomed lawn.
Top Page Image Contents