Troy-Bilt 020242-4 manual Preparing the Unit for Storage, Storing the Engine, Data Tag

Page 16

Section

6

Storage

Data Tag

Data tag information is very important if you need help from our Customer Service Department or an authorized service dealer.

The data tag (Figure 17) is located on the base of the pressure washer. For future reference, please copy the model, revision, and serial number of the pressure washer in the space below.

Figure 17 — Data Tag

 

 

 

 

 

 

 

 

 

 

 

 

Copy Model

 

 

 

 

 

MODEL

 

 

 

Number Here

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

REV NO

 

 

 

Copy Revision

 

SERIAL

 

 

 

Here

 

 

 

 

 

 

 

 

 

 

 

 

 

Copy Serial

 

 

 

 

 

 

 

 

 

 

Number Here

 

 

 

 

 

 

 

 

PSI

 

 

 

 

 

 

 

 

 

 

GPM

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Protecting the Pump

To protect the pump from damage caused by mineral deposits or freezing, use PumpSaver to treat pump.This prevents freeze damage and lubricates pistons and seals.

NOTE: PumpSaver is available as an optional accessory. It is not included with the pressure washer. Contact the nearest authorized service center or visit your local Lowe’s store to purchase PumpSaver.

CAUTION

You must protect your unit from freezing temperatures.

Failure to do so will permanently damage your pump and render your unit inoperable.

Freeze damage is not covered under warranty.

CAUTION

Read and follow all cautions and warnings on the PumpSaver can label.

• Always wear eye protection when using PumpSaver.

CAUTION

PumpSaver will drip from pump after treatment and will stain wood and concrete.

• Protect surfaces from dripping PumpSaver.

PREPARING THE UNIT FOR STORAGE

Water should not remain in the unit for long periods of time. Sediments or minerals can deposit on pump parts and “freeze” pump action. If you do not plan to use the pressure washer for more than 30 days, follow this procedure:

1.Flush detergent siphoning tube by placing filter into a pail of clean water while running pressure washer in low pressure mode. Flush for one to two minutes.

2.Shut off engine and let it cool, then remove high pressure and garden hoses. Disconnect spark plug wire from spark plug.

3.Empty pump of liquids by pulling engine recoil handle about 6 times.This should remove most liquid in pump.

4.Use pump saver to prevent corrosion build up and freezing of pump.

5.Store unit in a clean, dry area.

To use PumpSaver, make sure the pressure washer is turned off and disconnected from supply water. Read and follow all instructions and warnings given on the PumpSaver container.

NOTE: If PumpSaver is not available, draw RV antifreeze (non-alcohol) into the pump by pouring the solution into a 3-foot section of garden hose connected to inlet adapter and pulling recoil handle twice.

STORING THE ENGINE

See the engine operator’s manual for instructions on how to properly prepare the engine for storage.

16

Image 16
Contents Operator’s Manual / Manual del Operario Manual No GS Revision 0 12/02/2005Safety Rules Table of ContentsEquipment Description When Adding Fuel Operate pressure washer only outdoorsUnintentional sparking can result in fire or electric shock High pressure spray may damage fragile items including glass Section Features and Controls Know Your Pressure WasherAssembly Assembly SectionPreparing Pressure Washer for USE Assembly Add Engine Oil and FuelChecklist Before Starting Engine Connect Hose and Water Supply to PumpInspect inlet Screen, doHOW to USE Your Pressure Washer Section OperationPressure Washer Location To Start Pressure WasherHow to Stop Your Pressure Washer OperationHow to Use Accessory Tray How to Use Spray TipsLow Pressure High PressureCleaning and Applying Chemical Cleaning Detergent Siphoning TubePressure Washer Rinsing Automatic Cool Down SystemSection Maintenance SpecificationsGeneral Maintenance Recommendations Pressure Washer MaintenanceMaintenance Engine MaintenanceNozzle Maintenance Ring MaintenanceStorage Preparing the Unit for StorageStoring the Engine Data TagTroubleshooting TroubleshootingProblem Cause Correction Page TROY-BILT Owner Warranty Policy Effective November 1 About your equipment warrantyEquipment Consumer Use Commercial Use Portable Generator Years 2nd year parts onlyReglas de Seguridad Tabla DE ContenidosDescripción DEL Equipo Reglas DE SeguridadSección 1 Reglas de Seguridad Cuando Añada CombustibleCuando Pruebe LA Bujía DEL Motor Precaución Características y Controles Conozca SU Maquina Lavadora DE PresionMontaje MontajePreparando EL Lavador a Presión Para SU USO Agregar Aceite al Motor y Gasolina Sección 3 MontajeColoque la lavadora a presión sobre una superficie nivelada Conecte la Manguera y el Suministro de Agua a la Bomba Lista de Revision Previa al Arranque del MotorDeposite la gasolina adecuada en el tanque del combustible Proporcione el suministro de agua adecuadoOperación Cómo Usar SU Máquina Lavadora a PresiónUbicación del Lavadora a Presión Cómo Darle Arranque a su Máquina Lavadora a PresiónCómo Parar su Lavador a Presión Sección 4 OperaciónEl Pasador de la Seguridad Cómo Usar la Bandeja de Accesorios Cómo Usar las Puntas de RocíoLa Presión Baja La Presión AltaLimpieza y Aplicación del Químico Enjuage de la Máquina Lavadora a PresiónLimpiando el Tubo Sistema de Enfriamiento Automático Alivio TérmicoMantenimiento EspecificacionesRecomendaciones Generales Mantenimiento DE LA Maquina Lavadora a PresionSección 5 Mantenimiento Mantenimiento DEL MotorMantenimiento de la Boquilla Mantenimiento de los Anillos OSección 6 Almacenamiento Preparando LA Unidad Para SU AlmacenamientoAlmacenando EL Motor Etiqueta de DatosDiagnosticos de Averías Reparacion DE DañosEfectiva desde el 1 ro de Noviembre Equipo Para Uso Del Consumidor Para Uso ComercialGenerador Portátil Año