Telit Wireless Solutions 1vv0300773a manual Output Lines Speaker

Page 47

GE863-PRO3Hardware User Guide

1vv0300773a Rev. 0 - 24/01/08

8.2 OUTPUT LINES (Speaker)

8.2.1 Short description

The Telit GE863-PRO3provides two audio paths in receive section. Only one of the two paths can be active at a time, selectable by AXE hardware line or by AT command.

You must keep in mind the different audio characteristics of the receive blocks when designing:

Æthe “EAR_MT” lines EPN1 and EPP1 are the Differential Line-Out Drivers ; they can drive an external amplifier or directly a 16 Ω earpiece at –12dBFS (*) ;

Æthe “EAR_HF” lines EPPA1_2 and EPPA2 are the Fully Differential Power Buffers ; they can directly drive a 16Ω speaker in differential (balanced) or single ended (unbalanced) operation mode .

(*)FS : acronym of Full Scale. It is equal to 0dB, the maximum Hardware Analog Receive Gain of BaseBand Chip.

The “EAR_MT” audio path should be used for handset function, while the “EAR_HF” audio path is suited for hands-free function (car kit).

Both receiver outputs are B.T.L. type (Bridged Tie Load) and the OEM circuitry shall be designed bridged to reduce the common mode noise typically generated on the ground plane and to get the maximum power output from the device; however also a single ended circuitry can be designed for particular OEM application needs.

Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved

page 47 of 64

Page 46 Page 48
Image 47
Page 46 Page 48
Contents GE863-PRO3Hardware User Guide Contents GE863-PRO 3 Hardware User Guide This document is relating to the following products Disclaimer Overview Length 41,4 mm Width 31,4 mm Thickness 3,6 mm GE863-PRO3Mechanical DimensionsTelit GE863-PRO3module overall dimension are GE863-PRO3module connections D10 GND D11 Simvcc D12 Simclk E1 GND E2 Pwrmon DTE GPIO7 / Rftxdisable GSMC2 Vbatt C3 Vrtc C11 Simrst C12 Simio D1 Charge D2 VAUX1ON/OFF*-AP Nrst Reset ARMPB8 PB9PB7 PB0PB2 PB1PA3 HdmbXIN32 XOUT32Reserved GND VBATT2Balls Layout ARM PIO Controller a multiplexing ARM Port IO multiplexingARM PIO Controller B multiplexing ARM PIO Controller C multiplexing Turning on the GE863-PRO3GSM/GPRS Engine Hardware Commands+1,8/5 10kHardware shutdown Hardware Unconditional Reboot of GSM/GPRS Engine2Turning OFF the GE863-PRO3GSM/GPRS Engine Turning ON/OFF the GE863-PRO3ARM ON/OFF*-AP # GND AT+CFUN=4 Power SupplyGSM Power Supply Requirements AT+CFUN=1Vrtc Backup supply ARM Power Supply Requirements817A19A Seiko General Design RulesElectrical design Guidelines Suggested circuit is1.1 + 5V input Source Power Supply Design Guidelines 1.2 + 12V input Source Power Supply Design Guidelines Battery Source Power Supply Design Guidelines Battery Charge control Circuitry Design Guidelines GE863-PRO3Hardware User Guide Thermal Design Guidelines Power Supply PCB layout Guidelines GSM Antenna Requirements Antenna50 ohm GSM Antenna PCB line GuidelinesElectro Magnetic Interference Guidelines GSM Antenna installation GuidelinesOperating Range Interface levels Cmos Level Min Max Logic level specificationsAbsolute Maximum Ratings -Not Functional Parameter Min Max Operating Range Interface levels Cmos Vrtc Level Min Max GSM Gpio Current characteristics Level TypicalCmos 3.1V Current characteristics Level Typical Cmos 1.8V-A Current characteristics Level TypicalSignal Min Max Signal FunctionPhone reset Modem Serial Port Modem Serial Port 2 Debug Serial PortsSignals of the GE863-PRO3GSM/GPRS engine serial port are RS232 level translation An example of level translation circuitry of this kind is GE863-PRO3Hardware User Guide Audio Section Overview Short description Input Lines MicrophoneMicmt 1st differential microphone path Input Lines CharacteristicsOutput Lines Speaker Earmt Differential Line-out Drivers Path Output Lines CharacteristicsEvaluation Kit for Telit GE863- PRO3 Modules ON/OFF 10 GSM/GPRS General Purpose I/O10.4Using the Rftxmon Output GPIO3 Using a Gpio Pad as InputUsing a Gpio Pad as Output Using the RF Transmission Control GPIO7Using the Buzzer Output GPIO4 Using the Alarm OutputDevice Status 10.7Indication of network service availabilityLED status RTC Bypass out 10.9VAUX1 power outputOperating Range VAUX1 power supply PCB pad Design Mounting the GE863-PRO3on the Application Board11.1General StencilSolder paste Following is the recommended solder reflow profile 11.1.4 GE863-PRO3Solder Reflow3C/second max Section A-A Packing SystemModules orientation on tray Moisture Sensibility Conformity Assessment Issues Safety Recommandations Revision Date Changes Document Change Log

1vv0300773a specifications

Telit Wireless Solutions 1VV0300773A is an advanced cellular module specifically designed for a wide range of IoT applications. This module is part of Telit’s extensive portfolio, which is renowned for its reliability and innovation in the wireless communication space. The 1VV0300773A module stands out due to its compact design and robust performance, making it an ideal choice for developers looking to integrate cellular connectivity into their projects.

One of the main features of the 1VV0300773A is its support for multiple communication protocols, which enhances its versatility. The module is designed to support various LTE CAT M1 and NB-IoT networks. These technologies are critical for low-power wide-area network (LPWAN) applications, allowing devices to stay connected over long distances while consuming minimal energy. This is particularly beneficial for battery-operated devices in sectors like smart agriculture, smart cities, and industrial IoT.

The module is equipped with a powerful ARM Cortex-M3 processor, which enables efficient data processing and facilitates complex computations required for many IoT applications. Additionally, it features a comprehensive set of interfaces, including UART, GPIO, and I2C, enabling easy integration with various sensors and peripherals. This modularity ensures that developers can customize their applications based on specific business needs.

Security is another crucial aspect of the 1VV0300773A module. Telit incorporates advanced security features including secure boot, data encryption, and a secure element, ensuring that data transmitted over cellular networks is protected against unauthorized access. This commitment to security is vital in today’s increasingly connected world, where data privacy is a top concern.

Furthermore, the 1VV0300773A module supports extensive over-the-air firmware updates, allowing manufacturers to deploy updates and enhancements seamlessly. This capability extends the lifecycle of devices in the field and ensures that they can adapt to new requirements and security standards over time.

In summary, Telit Wireless Solutions 1VV0300773A offers a blend of advanced features, robust technologies, and essential characteristics tailored for the rapidly evolving IoT landscape. Its combination of multi-network support, secure communication, and efficient processing makes it a standout choice for developers and enterprises looking to enhance their connectivity solutions.
Top Page Image Contents