Telit Wireless Solutions 1vv0300773a manual GE863-PRO3Mechanical Dimensions

Page 7

GE863-PRO3Hardware User Guide

1vv0300773a Rev. 0 - 24/01/08

2 GE863-PRO3Mechanical Dimensions

The Telit GE863-PRO3module overall dimension are:

•Length: 41,4 mm

•Width: 31,4 mm

•Thickness: 3,6 mm

Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved

page 7 of 64

Image 7

Contents GE863-PRO3Hardware User Guide Contents GE863-PRO 3 Hardware User Guide This document is relating to the following products Disclaimer Overview Telit GE863-PRO3module overall dimension are GE863-PRO3Mechanical DimensionsLength 41,4 mm Width 31,4 mm Thickness 3,6 mm GE863-PRO3module connections D10 GND D11 Simvcc D12 Simclk E1 GND E2 Pwrmon DTE GPIO7 / Rftxdisable GSMC2 Vbatt C3 Vrtc C11 Simrst C12 Simio D1 Charge D2 VAUX1ON/OFF*-AP Nrst Reset ARMPB8 PB9PB7 PB0PB2 PB1PA3 HdmbXIN32 XOUT32Reserved GND VBATT2Balls Layout ARM PIO Controller a multiplexing ARM Port IO multiplexingARM PIO Controller B multiplexing ARM PIO Controller C multiplexing Turning on the GE863-PRO3GSM/GPRS Engine Hardware Commands+1,8/5 10k2Turning OFF the GE863-PRO3GSM/GPRS Engine Hardware Unconditional Reboot of GSM/GPRS EngineHardware shutdown Turning ON/OFF the GE863-PRO3ARM ON/OFF*-AP # GND AT+CFUN=4 Power SupplyGSM Power Supply Requirements AT+CFUN=1Vrtc Backup supply ARM Power Supply Requirements817A19A Seiko General Design RulesElectrical design Guidelines Suggested circuit is1.1 + 5V input Source Power Supply Design Guidelines 1.2 + 12V input Source Power Supply Design Guidelines Battery Source Power Supply Design Guidelines Battery Charge control Circuitry Design Guidelines GE863-PRO3Hardware User Guide Thermal Design Guidelines Power Supply PCB layout Guidelines GSM Antenna Requirements Antenna50 ohm GSM Antenna PCB line GuidelinesElectro Magnetic Interference Guidelines GSM Antenna installation GuidelinesAbsolute Maximum Ratings -Not Functional Parameter Min Max Logic level specificationsOperating Range Interface levels Cmos Level Min Max Operating Range Interface levels Cmos Vrtc Level Min Max GSM Gpio Current characteristics Level TypicalCmos 3.1V Current characteristics Level Typical Cmos 1.8V-A Current characteristics Level TypicalPhone reset Signal FunctionSignal Min Max Modem Serial Port Modem Serial Port 2 Debug Serial PortsSignals of the GE863-PRO3GSM/GPRS engine serial port are RS232 level translation An example of level translation circuitry of this kind is GE863-PRO3Hardware User Guide Audio Section Overview Short description Input Lines MicrophoneMicmt 1st differential microphone path Input Lines CharacteristicsOutput Lines Speaker Earmt Differential Line-out Drivers Path Output Lines CharacteristicsEvaluation Kit for Telit GE863- PRO3 Modules ON/OFF 10 GSM/GPRS General Purpose I/O10.4Using the Rftxmon Output GPIO3 Using a Gpio Pad as InputUsing a Gpio Pad as Output Using the RF Transmission Control GPIO7Using the Buzzer Output GPIO4 Using the Alarm OutputLED status 10.7Indication of network service availabilityDevice Status Operating Range VAUX1 power supply 10.9VAUX1 power outputRTC Bypass out PCB pad Design Mounting the GE863-PRO3on the Application Board11.1General StencilSolder paste Following is the recommended solder reflow profile 11.1.4 GE863-PRO3Solder Reflow3C/second max Section A-A Packing SystemModules orientation on tray Moisture Sensibility Conformity Assessment Issues Safety Recommandations Revision Date Changes Document Change Log