Telit Wireless Solutions 1vv0300773a manual Safety Recommandations

Page 63

GE863-PRO3Hardware User Guide

1vv0300773a Rev. 0 - 24/01/08

13 SAFETY RECOMMANDATIONS

READ CAREFULLY

Be sure the use of this product is allowed in the country and in the environment required. The use of this product may be dangerous and has to be avoided in the following areas:

‰Where it can interfere with other electronic devices in environments such as hospitals, airports, aircrafts, etc

‰Where there is risk of explosion such as gasoline stations, oil refineries, etc

It is responsibility of the user to enforce the country regulation and the specific environment regulation.

Do not disassemble the product; any mark of tampering will compromise the warranty validity.

We recommend following the instructions of the hardware user guides for a correct wiring of the product. The product has to be supplied with a stabilized voltage source and the wiring has to be conforming to the security and fire prevention regulations.

The product has to be handled with care, avoiding any contact with the pins because electrostatic discharges may damage the product itself. Same cautions have to be taken for the SIM, checking carefully the instruction for its use. Do not insert or remove the SIM when the product is in power saving mode.

The system integrator is responsible of the functioning of the final product; therefore, care has to be taken to the external components of the module, as well as of any project or installation issue, because the risk of disturbing the GSM network or external devices or having impact on the security. Should there be any doubt, please refer to the technical documentation and the regulations in force.

Every module has to be equipped with a proper antenna with specific characteristics. The antenna has to be installed with care in order to avoid any interference with other electronic devices and has to guarantee a minimum distance from the body (20 cm). In case of this requirement cannot be satisfied, the system integrator has to assess the final product against the SAR regulation.

The European Community provides some Directives for the electronic equipments introduced on the market. All the relevant information’s are available on the European Community website:

http://europa.eu.int/comm/enterprise/rtte/dir99-5.htm

The text of the Directive 99/05 regarding telecommunication equipments is available, while the applicable Directives (Low Voltage and EMC) are available at:

http://europa.eu.int/comm/enterprise/electr_equipment/index_en.htm

Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved

page 63 of 64

Image 63
Contents GE863-PRO3Hardware User Guide Contents GE863-PRO 3 Hardware User Guide This document is relating to the following products Disclaimer Overview GE863-PRO3Mechanical Dimensions Telit GE863-PRO3module overall dimension areLength 41,4 mm Width 31,4 mm Thickness 3,6 mm GE863-PRO3module connections D10 GND D11 Simvcc D12 Simclk E1 GND E2 Pwrmon DTE GPIO7 / Rftxdisable GSMC2 Vbatt C3 Vrtc C11 Simrst C12 Simio D1 Charge D2 VAUX1ON/OFF*-AP Nrst Reset ARMPB8 PB9PB7 PB0PB2 PB1PA3 HdmbXIN32 XOUT32Reserved GND VBATT2Balls Layout ARM PIO Controller a multiplexing ARM Port IO multiplexingARM PIO Controller B multiplexing ARM PIO Controller C multiplexing Turning on the GE863-PRO3GSM/GPRS Engine Hardware Commands+1,8/5 10kHardware Unconditional Reboot of GSM/GPRS Engine 2Turning OFF the GE863-PRO3GSM/GPRS EngineHardware shutdown Turning ON/OFF the GE863-PRO3ARM ON/OFF*-AP # GND AT+CFUN=4 Power SupplyGSM Power Supply Requirements AT+CFUN=1Vrtc Backup supply ARM Power Supply Requirements817A19A Seiko General Design RulesElectrical design Guidelines Suggested circuit is1.1 + 5V input Source Power Supply Design Guidelines 1.2 + 12V input Source Power Supply Design Guidelines Battery Source Power Supply Design Guidelines Battery Charge control Circuitry Design Guidelines GE863-PRO3Hardware User Guide Thermal Design Guidelines Power Supply PCB layout Guidelines GSM Antenna Requirements Antenna50 ohm GSM Antenna PCB line GuidelinesElectro Magnetic Interference Guidelines GSM Antenna installation GuidelinesLogic level specifications Absolute Maximum Ratings -Not Functional Parameter Min MaxOperating Range Interface levels Cmos Level Min Max Operating Range Interface levels Cmos Vrtc Level Min Max GSM Gpio Current characteristics Level TypicalCmos 3.1V Current characteristics Level Typical Cmos 1.8V-A Current characteristics Level TypicalSignal Function Phone resetSignal Min Max Modem Serial Port Modem Serial Port 2 Debug Serial PortsSignals of the GE863-PRO3GSM/GPRS engine serial port are RS232 level translation An example of level translation circuitry of this kind is GE863-PRO3Hardware User Guide Audio Section Overview Short description Input Lines MicrophoneMicmt 1st differential microphone path Input Lines CharacteristicsOutput Lines Speaker Earmt Differential Line-out Drivers Path Output Lines CharacteristicsEvaluation Kit for Telit GE863- PRO3 Modules ON/OFF 10 GSM/GPRS General Purpose I/O10.4Using the Rftxmon Output GPIO3 Using a Gpio Pad as InputUsing a Gpio Pad as Output Using the RF Transmission Control GPIO7Using the Buzzer Output GPIO4 Using the Alarm Output10.7Indication of network service availability LED statusDevice Status 10.9VAUX1 power output Operating Range VAUX1 power supplyRTC Bypass out PCB pad Design Mounting the GE863-PRO3on the Application Board11.1General StencilSolder paste Following is the recommended solder reflow profile 11.1.4 GE863-PRO3Solder Reflow3C/second max Section A-A Packing System Modules orientation on tray Moisture Sensibility Conformity Assessment Issues Safety Recommandations Revision Date Changes Document Change Log