Walker SB6670 Lock Stopper Pin in Place, Adjust Brush to Ground Contact, GHS Blower Intake Cover

Page 30

Assembly Instructions

6.Remove the hairpin from the welded sleeve on the right hand side of the broom mounting bracket. Carefully pull out the stopper pin to its most extended position and lock in place with the hairpin.

Welded Sleeve

Hairpin

Stopper Pin

Lock Stopper Pin in Place

NOTE: The pin in the innermost position is used to prevent the female hitch on the broom from being pulled up by the brush ground contact adjustment spring, thus facilitating mounting and dismounting of the broom.

7.Adjust brush ground contact by threading knob. Refer to Ground Contact Knob in Operating

Instructions.

Ground Contact Knob

Adjust Brush to Ground Contact

8.Retract the parking stands and secure with the hairpins prior to operation.

9.To install the optional tire chains:

a.Remove the tractor wheels.

b.Attach the tire chains to the wheels.

c.Place the wheel spacer plates on the lug bolts. The wheel spacer plates provide clearance for the chains between the tires and the tractor body.

d.Place the wheels back on the tractor.

e.Reinstall and tighten the lug bolts.

10.For GHS (Grass Handling System) equipped Walker tractors, install a blower intake cover in the blower intake tube. The cover “unloads” the blower and seals the intake to effectively elimi- nate power loss and noise when the blower is not being used.

Blower Intake

Cover

GHS Blower Intake Cover

11.For stability of the tractor when transporting with the rotary broom in raised position, approxi- mately 80 lb (36 kg) of counterweight should be installed on the tail of the tractor. Optional tail weights for the various tractor models are avail- able from your Walker dealer or a sandbag or similar weight may be used.

Optional Gauge Wheel Installation

NOTE: Gauge wheels are required for lawn work or heavy loads.

26

Image 30

Contents Illustrated Parts Manual Foreword Table of Contents Implement Hitch Assembly Electrical Components Maintenance Schedule ChartTorque Specifications KEY to Abbreviations Used in Illustrated Parts ListIdentifying Number Locations General InformationGlossary Fill In By PurchaserSerial Number Serial Number Rotary Broom Serial Number LocationUnit Descriptions Dozer Blade SpecificationsImplement Hitch Rotary BroomTWO-STAGE Snowblower Debris Blower Implement Hitch Top View Not Installed Component IdentificationDozer Blade Rear View and Right Side View Not Installed Rotary Broom Rear View and Right Side View Not Installed TWO-STAGE Snowblower Two-Stage Snowblower Rear View Not Installed Debris Blower Front View and Left Side View Not Installed Debris Blower Rear View and Right Side View Not Installed Safety Instructions Before OperatingDo not operate with bystanders in the area Operating Maintenance SAFETY, CONTROL, and Instruction Decals PTO Shield Walker P/N Attaching Hitch Hitch Mount AdjustSAFETY, CONTROL, and Instruction Decals Implement Hitch Installation Assembly InstructionsSetup Instructions Implement Hitch Jam Nut AdjustmentAttach Wiring Harness and Toggle Switch Drill Holes for Implement Hitch WiringAttach Toggle Switch Mounting Bracket Connect Harness Wire to Circuit BreakerComplete Implement Hitch Wiring Implement Hitch Wiring Diagram Attach Spring to Blade Assembly Insert Adjustment Pin and Set Blade AngleInsert Female Hitch into Blade Attachment Install Skid Shoes Rotary Boom InstallationAttach Blade to Tractor Attach Broom to Implement Hitch Prepare Rotary Broom for InstallationAssemble Rotary Broom Driveline Connect Broom Driveline to Tractor PTO ShaftAdjust Brush to Ground Contact Lock Stopper Pin in PlaceGHS Blower Intake Cover Install Hand Guard on Chute Install Plastic Insert over Chute Base LipInstall Rotation Worm Assembly Install Chute over Plastic InsertInstall Skid Shoes Snowblower Installation Attach Drive Shaft Yoke to Reduction Shaft Install Bolt in Reduction BoxInstall Reduction Box Cover Mount Female Hitch to SnowblowerAttach Parallel Bar to Female Hitch Attach Snowblower to Implement HitchConnect Driveline Coupler to Tractor PTO Insert Rotation Handle into Rotation WormAttach Tractor PTO to Debris Blower Input Shaft Attach Debris Blower to Implement HitchRefer to Angle Adjustment Pin in Operating Refer to Hitch Locking Lever in Operating InstrucRefer to Angle Adjustment Lever in Operating Refer to Ground Contact Knob in OperatingOperating Instructions TWO-STAGE Snowblower ControlsTWO-STAGE Snowblower Operation Engaging the Snowblower PTO Clutch EngagedThrow Snow to Both Sides Clogging Checklist Throw Snow to One SideRaising and Lowering the Debris Blower Engaging the Debris Blower Stopping the MachineModel Service Item Daily Hours Maintenance InstructionsMaintenance procedures requiring special training or Tools should be performed by a trained technicianRotary Broom Gearbox with Cover Removed LubricationRotary Broom Gearbox Remove Chain Guard CoverRemove Reduction Box Cover Snowblower Lubricant Plug LocationTwo-Stage Snowblower Reduction Chain Grease Fitting and Oil Point LubricationLubrication Implement Hitch Lubrication Points Angle Adjustment Pin Oil Dozer Blade Lubrication Points Ident Rotary Broom Lubrication Points Location Type Two-Stage Snowblower Lubrication Points Ident Lubrication Location Type Debris Blower Lubrication Points REPLACING/REPAIRING Dozer Blade Cutting Edge Replacement Rotary Broom BrushSupport Rear of Broom Housing Remove Brush from Broom Housing Loosen Chain Idler and Set ScrewsReplace Rotary Broom Gearbox Rotary Broom Drive Chain Rotary Broom Drive Sprocket Remove Chain Guard Loosen Chain TensionReplace Drive Chain Sprocket WearCheck Sprocket Alignment with Chain Installed Remove and Replace SprocketAlign Sprockets Replace Snowblower Gearbox Reduction Sprocket Wear Replace Reduction ChainTwo-Stage Snowblower Reduction Sprocket Debris Blower Drive BeltAdjustments Dozer Blade Skid ShoesSkid Shoe Height Adjustment Rotary Broom Brush Leveling Side to Side Level Adjustment Rotary Broom Gauge WheelsGauge Wheel Height Adjustment Ance under the blade. On level, paved surfaces Loosen Chain Idler NutProper Drive Chain Tension Two-Stage Snowblower Skid Shoes Surface. On uneven or gravel surfaces, allow 1/2Proper Drive Belt Deflection Drive Belt Tension Adjustment Debris Blower Rotation Pinions Debris Blower Rotation Pinions Handle AdjustmentTorque Specifications Removal and Storage Instructions RemovalDetach Blade from Implement Hitch Detach Rotary Broom from Implement Hitch Detach Snowblower from Implement HitchDetach Implement Hitch from Tractor END of Season StorageRotary Broom Implement Hitch Assembly FastenersUse only genuine Walker replacement parts Implement Hitch Electrical Components Implement Hitch Electrical Components FastenersRAD Technologies Inc Implement Hitch Electrical Components Dozer Blade Assembly Dozer Blade Assembly Rotary Broom Assembly Rotary Broom AssemblyKit I391 Side Caster Wheels Kit Rotary Broom Assembly Gearbox Assembly Driveline and Sprockets Assembly FastenersRotary Broom Drive Components Rotary Broom Drive Components Snowblower Mount Assembly Snowblower Housing ComponentsChute Rotation Assembly Reduction Box AssemblySnowblower Housing Components Snowblower Drive Components Driveline and Auger ComponentsSnowblower Drive Components Debris Blower Components Debris Blower ComponentsDebris Blower Components Debris Blower Manual Rotation Components Debris Blower Manual Rotation ComponentsDebris Blower Manual Rotation Components KEY to Abbreviations Used in Illustrated Parts Manual Limited Warranty For Walker Commercial Rider Mower Walker MFG. CO E. Harmony ROAD, Fort COLLINS, CO 80528 970