Walker DB6680, SB6670, DB6660, RB6650, IH6620 Refer to Hitch Locking Lever in Operating Instruc

Page 36

Assembly Instructions

9.For stability of the tractor when transporting with the debris blower in raised position, approxi- mately 80 lb (36 kg) of counterweight should be installed on the tail of the tractor. Optional tail weights for the various tractor models are avail- able from your Walker dealer or a sandbag or similar weight may be used.

PREOPERATING CHECKLIST

Before operating any of the implements for the first time, and as a routine before daily operations, it is important to make sure the machine is properly pre- pared and ready for operation. The following is a list of items to be checked. (For machines with fre- quent operation, some of these items will not need to be checked every day, but the operator should be aware of the condition of each.)

CHECK TRACTOR PREOPERATING

CHECKLIST

Refer to the appropriate Tractor Owner’s Manual.

CHECK GAUGE WHEEL OR SKID SHOE ADJUSTMENT

Refer to ADJUSTMENTS of Dozer Blade Skid Shoes in Maintenance Instructions.

Refer to ADJUSTMENTS of Rotary Broom Gauge Wheels in Maintenance Instructions.

Refer to ADJUSTMENTS of Two-Stage Snow- blower Skid Shoes in Maintenance Instructions.

Refer to ADJUSTMENTS of Debris Blower Front Gauge Wheel in Maintenance Instructions.

CHECK OPTIONAL TIRE CHAINS

Tire chains should always be used when operating the machine in icy conditions. If the tractor is equipped with the optional tire chains, make sure the chains are in good condition and are installed properly.

CHECK TRACTOR TAILWEIGHT

Make sure 80 lb (36 kg) weight has been installed on rear of tractor.

Implement Hitch

CHECK LIFT SWITCH OPERATION

Raise and lower the implement hitch to make sure the lift switch and linear actuator operate properly.

CHECK HITCH LOCKING LEVER

Lock and unlock the male hitch to make sure the locking mechanism functions properly.

Refer to Hitch Locking Lever in Operating Instruc-

tions.

Dozer Blade

CHECK CUTTING EDGE

Make sure the cutting edge is not nicked, bent or worn.

Refer to REPLACING/REPAIRING of Dozer Blade Cutting Edge in Maintenance Instructions.

CHECK TRIP SPRING

Check trip spring tension.

Refer to Trip Spring in Operating Instructions.

Check trip spring lockout bracket.

Refer to Normal Operation or Rigid Blade Opera- tion in Operating Instructions.

CHECK SWIVEL ADJUSTMENT

Refer to Angle Adjustment Pin in Operating In-

structions.

Rotary Broom

CHECK BRUSH

Make sure the brush is clear of snow and/or ice.

Make sure the brush is free to rotate.

Check that the bristles are in good condition and are not worn or bent.

32

Image 36
Contents Illustrated Parts Manual Foreword Table of Contents Maintenance Schedule Chart Torque SpecificationsImplement Hitch Assembly Electrical Components KEY to Abbreviations Used in Illustrated Parts ListGeneral Information GlossaryIdentifying Number Locations Fill In By PurchaserSerial Number Serial Number Rotary Broom Serial Number LocationUnit Descriptions Specifications Implement HitchDozer Blade Rotary BroomTWO-STAGE Snowblower Debris Blower Implement Hitch Top View Not Installed Component IdentificationDozer Blade Rear View and Right Side View Not Installed Rotary Broom Rear View and Right Side View Not Installed TWO-STAGE Snowblower Two-Stage Snowblower Rear View Not Installed Debris Blower Front View and Left Side View Not Installed Debris Blower Rear View and Right Side View Not Installed Safety Instructions Before OperatingDo not operate with bystanders in the area Operating Maintenance SAFETY, CONTROL, and Instruction Decals PTO Shield Walker P/N Attaching Hitch Hitch Mount AdjustSAFETY, CONTROL, and Instruction Decals Assembly Instructions Setup InstructionsImplement Hitch Installation Implement Hitch Jam Nut AdjustmentDrill Holes for Implement Hitch Wiring Attach Toggle Switch Mounting BracketAttach Wiring Harness and Toggle Switch Connect Harness Wire to Circuit BreakerComplete Implement Hitch Wiring Implement Hitch Wiring Diagram Attach Spring to Blade Assembly Insert Adjustment Pin and Set Blade AngleInsert Female Hitch into Blade Attachment Install Skid Shoes Rotary Boom InstallationAttach Blade to Tractor Prepare Rotary Broom for Installation Assemble Rotary Broom DrivelineAttach Broom to Implement Hitch Connect Broom Driveline to Tractor PTO ShaftAdjust Brush to Ground Contact Lock Stopper Pin in PlaceGHS Blower Intake Cover Install Hand Guard on Chute Install Plastic Insert over Chute Base LipInstall Rotation Worm Assembly Install Chute over Plastic InsertInstall Skid Shoes Snowblower Installation Install Bolt in Reduction Box Install Reduction Box CoverAttach Drive Shaft Yoke to Reduction Shaft Mount Female Hitch to SnowblowerAttach Snowblower to Implement Hitch Connect Driveline Coupler to Tractor PTOAttach Parallel Bar to Female Hitch Insert Rotation Handle into Rotation WormAttach Tractor PTO to Debris Blower Input Shaft Attach Debris Blower to Implement HitchRefer to Angle Adjustment Pin in Operating Refer to Hitch Locking Lever in Operating InstrucRefer to Angle Adjustment Lever in Operating Refer to Ground Contact Knob in OperatingOperating Instructions TWO-STAGE Snowblower ControlsTWO-STAGE Snowblower Operation Engaging the Snowblower PTO Clutch EngagedThrow Snow to Both Sides Clogging Checklist Throw Snow to One SideRaising and Lowering the Debris Blower Engaging the Debris Blower Stopping the MachineMaintenance Instructions Maintenance procedures requiring special training orModel Service Item Daily Hours Tools should be performed by a trained technicianLubrication Rotary Broom GearboxRotary Broom Gearbox with Cover Removed Remove Chain Guard CoverSnowblower Lubricant Plug Location Two-Stage Snowblower Reduction ChainRemove Reduction Box Cover Grease Fitting and Oil Point LubricationLubrication Implement Hitch Lubrication Points Angle Adjustment Pin Oil Dozer Blade Lubrication Points Ident Rotary Broom Lubrication Points Location Type Two-Stage Snowblower Lubrication Points Ident Lubrication Location Type Debris Blower Lubrication Points REPLACING/REPAIRING Dozer Blade Cutting Edge Replacement Rotary Broom BrushSupport Rear of Broom Housing Remove Brush from Broom Housing Loosen Chain Idler and Set ScrewsReplace Rotary Broom Gearbox Rotary Broom Drive Chain Remove Chain Guard Loosen Chain Tension Replace Drive ChainRotary Broom Drive Sprocket Sprocket WearCheck Sprocket Alignment with Chain Installed Remove and Replace SprocketAlign Sprockets Replace Snowblower Gearbox Replace Reduction Chain Two-Stage Snowblower Reduction SprocketReduction Sprocket Wear Debris Blower Drive BeltAdjustments Dozer Blade Skid ShoesSkid Shoe Height Adjustment Rotary Broom Brush Leveling Side to Side Level Adjustment Rotary Broom Gauge WheelsGauge Wheel Height Adjustment Loosen Chain Idler Nut Proper Drive Chain Tension Two-Stage Snowblower Skid ShoesAnce under the blade. On level, paved surfaces Surface. On uneven or gravel surfaces, allow 1/2Proper Drive Belt Deflection Drive Belt Tension Adjustment Debris Blower Rotation Pinions Debris Blower Rotation Pinions Handle AdjustmentTorque Specifications Removal and Storage Instructions RemovalDetach Blade from Implement Hitch Detach Rotary Broom from Implement Hitch Detach Snowblower from Implement HitchDetach Implement Hitch from Tractor END of Season StorageRotary Broom Implement Hitch Assembly FastenersUse only genuine Walker replacement parts Implement Hitch Electrical Components Implement Hitch Electrical Components FastenersRAD Technologies Inc Implement Hitch Electrical Components Dozer Blade Assembly Dozer Blade Assembly Rotary Broom Assembly Rotary Broom AssemblyKit I391 Side Caster Wheels Kit Rotary Broom Assembly Gearbox Assembly Driveline and Sprockets Assembly FastenersRotary Broom Drive Components Rotary Broom Drive Components Snowblower Housing Components Chute Rotation AssemblySnowblower Mount Assembly Reduction Box AssemblySnowblower Housing Components Snowblower Drive Components Driveline and Auger ComponentsSnowblower Drive Components Debris Blower Components Debris Blower ComponentsDebris Blower Components Debris Blower Manual Rotation Components Debris Blower Manual Rotation ComponentsDebris Blower Manual Rotation Components KEY to Abbreviations Used in Illustrated Parts Manual Limited Warranty For Walker Commercial Rider Mower Walker MFG. CO E. Harmony ROAD, Fort COLLINS, CO 80528 970