Walker DB6680, SB6670, DB6660, RB6650 Drive Belt Tension Adjustment Debris Blower Rotation Pinions

Page 66

Maintenance Instructions

ADJUSTMENTS

Blower Pulley

Bearing

Support Bolts

Adjustment Eye Bolts

Drive Belt Tension Adjustment

Debris Blower Rotation Pinions

The two (2) rotation pinions should slightly contact each other without any resistance.

1.Loosen the set screw of each stop ring on the rotation handle.

2.Keeping the two (2) pinions slightly in contact with each other, position the upper stop ring against the lower support and tighten the screw.

3.Position the lower stop ring close to the lower support and tighten the set screw. The rotation handle should rotate freely without excessive end play.

Debris Blower Rotation Handle

With the rotation pinions properly adjusted, the two

(2)stop rings should be positioned close enough to the lower support to allow the rotation handle to ro- tate freely without excessive end play.

Rotation

Handle

Upper

Stop Ring

& Set Screw

Lower

Support

Lower

Stop Ring

& Set Screw Rotation

Pinions

Debris Blower Rotation Pinions

& Handle Adjustment

66

Image 66
Contents Illustrated Parts Manual Foreword Table of Contents Implement Hitch Assembly Electrical Components Maintenance Schedule ChartTorque Specifications KEY to Abbreviations Used in Illustrated Parts ListIdentifying Number Locations General InformationGlossary Fill In By PurchaserSerial Number Serial Number Rotary Broom Serial Number LocationUnit Descriptions Dozer Blade SpecificationsImplement Hitch Rotary BroomTWO-STAGE Snowblower Debris Blower Implement Hitch Top View Not Installed Component IdentificationDozer Blade Rear View and Right Side View Not Installed Rotary Broom Rear View and Right Side View Not Installed TWO-STAGE Snowblower Two-Stage Snowblower Rear View Not Installed Debris Blower Front View and Left Side View Not Installed Debris Blower Rear View and Right Side View Not Installed Safety Instructions Before OperatingDo not operate with bystanders in the area Operating Maintenance SAFETY, CONTROL, and Instruction Decals PTO Shield Walker P/N Attaching Hitch Hitch Mount AdjustSAFETY, CONTROL, and Instruction Decals Implement Hitch Installation Assembly InstructionsSetup Instructions Implement Hitch Jam Nut AdjustmentAttach Wiring Harness and Toggle Switch Drill Holes for Implement Hitch WiringAttach Toggle Switch Mounting Bracket Connect Harness Wire to Circuit BreakerComplete Implement Hitch Wiring Implement Hitch Wiring Diagram Attach Spring to Blade Assembly Insert Adjustment Pin and Set Blade AngleInsert Female Hitch into Blade Attachment Install Skid Shoes Rotary Boom InstallationAttach Blade to Tractor Attach Broom to Implement Hitch Prepare Rotary Broom for InstallationAssemble Rotary Broom Driveline Connect Broom Driveline to Tractor PTO ShaftAdjust Brush to Ground Contact Lock Stopper Pin in PlaceGHS Blower Intake Cover Install Hand Guard on Chute Install Plastic Insert over Chute Base LipInstall Rotation Worm Assembly Install Chute over Plastic InsertInstall Skid Shoes Snowblower Installation Attach Drive Shaft Yoke to Reduction Shaft Install Bolt in Reduction BoxInstall Reduction Box Cover Mount Female Hitch to SnowblowerAttach Parallel Bar to Female Hitch Attach Snowblower to Implement HitchConnect Driveline Coupler to Tractor PTO Insert Rotation Handle into Rotation WormAttach Tractor PTO to Debris Blower Input Shaft Attach Debris Blower to Implement HitchRefer to Angle Adjustment Pin in Operating Refer to Hitch Locking Lever in Operating InstrucRefer to Angle Adjustment Lever in Operating Refer to Ground Contact Knob in OperatingOperating Instructions TWO-STAGE Snowblower ControlsTWO-STAGE Snowblower Operation Engaging the Snowblower PTO Clutch EngagedThrow Snow to Both Sides Clogging Checklist Throw Snow to One SideRaising and Lowering the Debris Blower Engaging the Debris Blower Stopping the MachineModel Service Item Daily Hours Maintenance InstructionsMaintenance procedures requiring special training or Tools should be performed by a trained technicianRotary Broom Gearbox with Cover Removed LubricationRotary Broom Gearbox Remove Chain Guard CoverRemove Reduction Box Cover Snowblower Lubricant Plug LocationTwo-Stage Snowblower Reduction Chain Grease Fitting and Oil Point LubricationLubrication Implement Hitch Lubrication Points Angle Adjustment Pin Oil Dozer Blade Lubrication Points Ident Rotary Broom Lubrication Points Location Type Two-Stage Snowblower Lubrication Points Ident Lubrication Location Type Debris Blower Lubrication Points REPLACING/REPAIRING Dozer Blade Cutting Edge Replacement Rotary Broom BrushSupport Rear of Broom Housing Remove Brush from Broom Housing Loosen Chain Idler and Set ScrewsReplace Rotary Broom Gearbox Rotary Broom Drive Chain Rotary Broom Drive Sprocket Remove Chain Guard Loosen Chain TensionReplace Drive Chain Sprocket WearCheck Sprocket Alignment with Chain Installed Remove and Replace SprocketAlign Sprockets Replace Snowblower Gearbox Reduction Sprocket Wear Replace Reduction ChainTwo-Stage Snowblower Reduction Sprocket Debris Blower Drive BeltAdjustments Dozer Blade Skid ShoesSkid Shoe Height Adjustment Rotary Broom Brush Leveling Side to Side Level Adjustment Rotary Broom Gauge WheelsGauge Wheel Height Adjustment Ance under the blade. On level, paved surfaces Loosen Chain Idler NutProper Drive Chain Tension Two-Stage Snowblower Skid Shoes Surface. On uneven or gravel surfaces, allow 1/2Proper Drive Belt Deflection Drive Belt Tension Adjustment Debris Blower Rotation Pinions Debris Blower Rotation Pinions Handle AdjustmentTorque Specifications Removal and Storage Instructions RemovalDetach Blade from Implement Hitch Detach Rotary Broom from Implement Hitch Detach Snowblower from Implement HitchDetach Implement Hitch from Tractor END of Season StorageRotary Broom Implement Hitch Assembly FastenersUse only genuine Walker replacement parts Implement Hitch Electrical Components Implement Hitch Electrical Components FastenersRAD Technologies Inc Implement Hitch Electrical Components Dozer Blade Assembly Dozer Blade Assembly Rotary Broom Assembly Rotary Broom AssemblyKit I391 Side Caster Wheels Kit Rotary Broom Assembly Gearbox Assembly Driveline and Sprockets Assembly FastenersRotary Broom Drive Components Rotary Broom Drive Components Snowblower Mount Assembly Snowblower Housing ComponentsChute Rotation Assembly Reduction Box AssemblySnowblower Housing Components Snowblower Drive Components Driveline and Auger ComponentsSnowblower Drive Components Debris Blower Components Debris Blower ComponentsDebris Blower Components Debris Blower Manual Rotation Components Debris Blower Manual Rotation ComponentsDebris Blower Manual Rotation Components KEY to Abbreviations Used in Illustrated Parts Manual Limited Warranty For Walker Commercial Rider Mower Walker MFG. CO E. Harmony ROAD, Fort COLLINS, CO 80528 970