Walker SB6670 General Information, Glossary, Identifying Number Locations, Fill In By Purchaser

Page 5

General Information

HIGHLIGHTED INFORMATION

Walker Manufacturing recommends that any ser- vice requiring special training or tools be performed by an authorized Walker Mower Dealer. There are several general practices to be aware of in the area of safety. Most accidents associated with the oper- ation or maintenance of a Walker product are caused by disregarding basic safety precautions or specific warnings. Such accidents, in most cases, can be prevented by being aware of the dangers present.

Information of special importance has been high- lighted in bold type in this manual. Refer to Safety Instructions for the meanings of DANGER, WARN- ING, CAUTION, IMPORTANT, and NOTE.

GLOSSARY

There are many terms that are either unique to this equipment or that are used as acronyms. The fol- lowing terms and their definitions will help while us- ing this manual.

FORWARD SPEED CONTROL (FSC) controls the maximum forward speed of the tractor; func- tioning as a cruise control.

IMPLEMENT refers to the dozer blade, rotary broom, two-stage snowblower, or debris blower used with the tractor with an implement hitch in- stalled.

LEFT HAND (LH) refers to the left-hand side of the machine when the operator is seated facing forward in the tractor seat.

MACHINE consists of the implement installed on the tractor, functioning as a single unit.

POWER TAKE-OFF (PTO) transmits engine power to run the rotary broom, two-stage snow- blower, or debris blower.

RIGHT HAND (RH) refers to the right-hand side of the machine when the operator is seated fac- ing forward in the tractor seat.

TRACTOR is the prime mover, including the en- gine, drivetrain, operator seat, and controls to operate the implement.

IDENTIFYING NUMBER LOCATIONS

The implement hitch serial number is affixed to the top of the male hitch assembly, underneath the PTO shield. The dozer blade serial number is af- fixed to the LH side of the hitch box on the back side of the blade. The rotary broom serial number is affixed on the RH side of the pivot bracket. The snowblower serial number is affixed on the RH side of the snowblower head frame. The debris blower serial number is affixed to the top RH side of the hitch. Model and serial numbers are helpful when obtaining replacement parts and maintenance as- sistance. For ready reference, please record these numbers in the space provided.

Implement Hitch Model No.

IH6620

Implement Hitch Serial No. _______________

Dozer Blade Model No.

DB6660

Dozer Blade Serial No. __________________

Rotary Broom Model No.

RB6650

Rotary Broom Serial No. _________________

Two-Stage Snowblower Model No. SB6670

Two-Stage Snowblower Serial No. _________

Debris Blower Model No.

DB6680

Debris Blower Serial No. _________________

Date of Purchase _______________________

Fill In By Purchaser

1

Image 5
Contents Illustrated Parts Manual Foreword Table of Contents Torque Specifications Maintenance Schedule ChartImplement Hitch Assembly Electrical Components KEY to Abbreviations Used in Illustrated Parts ListGlossary General InformationIdentifying Number Locations Fill In By PurchaserSerial Number Rotary Broom Serial Number Location Serial NumberUnit Descriptions Implement Hitch SpecificationsDozer Blade Rotary BroomTWO-STAGE Snowblower Debris Blower Component Identification Implement Hitch Top View Not InstalledDozer Blade Rear View and Right Side View Not Installed Rotary Broom Rear View and Right Side View Not Installed TWO-STAGE Snowblower Two-Stage Snowblower Rear View Not Installed Debris Blower Front View and Left Side View Not Installed Debris Blower Rear View and Right Side View Not Installed Do not operate with bystanders in the area Safety InstructionsBefore Operating Operating Maintenance PTO Shield Walker P/N Attaching Hitch Hitch Mount Adjust SAFETY, CONTROL, and Instruction DecalsSAFETY, CONTROL, and Instruction Decals Setup Instructions Assembly InstructionsImplement Hitch Installation Implement Hitch Jam Nut AdjustmentAttach Toggle Switch Mounting Bracket Drill Holes for Implement Hitch WiringAttach Wiring Harness and Toggle Switch Connect Harness Wire to Circuit BreakerComplete Implement Hitch Wiring Implement Hitch Wiring Diagram Insert Female Hitch into Blade Attachment Attach Spring to Blade AssemblyInsert Adjustment Pin and Set Blade Angle Attach Blade to Tractor Install Skid ShoesRotary Boom Installation Assemble Rotary Broom Driveline Prepare Rotary Broom for InstallationAttach Broom to Implement Hitch Connect Broom Driveline to Tractor PTO ShaftGHS Blower Intake Cover Adjust Brush to Ground ContactLock Stopper Pin in Place Install Plastic Insert over Chute Base Lip Install Hand Guard on ChuteInstall Skid Shoes Snowblower Installation Install Rotation Worm AssemblyInstall Chute over Plastic Insert Install Reduction Box Cover Install Bolt in Reduction BoxAttach Drive Shaft Yoke to Reduction Shaft Mount Female Hitch to SnowblowerConnect Driveline Coupler to Tractor PTO Attach Snowblower to Implement HitchAttach Parallel Bar to Female Hitch Insert Rotation Handle into Rotation WormAttach Debris Blower to Implement Hitch Attach Tractor PTO to Debris Blower Input ShaftRefer to Hitch Locking Lever in Operating Instruc Refer to Angle Adjustment Pin in OperatingRefer to Ground Contact Knob in Operating Refer to Angle Adjustment Lever in OperatingTWO-STAGE Snowblower Operation Operating InstructionsTWO-STAGE Snowblower Controls PTO Clutch Engaged Engaging the SnowblowerThrow Snow to One Side Throw Snow to Both Sides Clogging ChecklistRaising and Lowering the Debris Blower Stopping the Machine Engaging the Debris BlowerMaintenance procedures requiring special training or Maintenance InstructionsModel Service Item Daily Hours Tools should be performed by a trained technicianRotary Broom Gearbox LubricationRotary Broom Gearbox with Cover Removed Remove Chain Guard CoverTwo-Stage Snowblower Reduction Chain Snowblower Lubricant Plug LocationRemove Reduction Box Cover Grease Fitting and Oil Point LubricationLubrication Implement Hitch Lubrication Points Angle Adjustment Pin Oil Dozer Blade Lubrication Points Ident Rotary Broom Lubrication Points Location Type Two-Stage Snowblower Lubrication Points Ident Lubrication Location Type Debris Blower Lubrication Points Support Rear of Broom Housing REPLACING/REPAIRINGDozer Blade Cutting Edge Replacement Rotary Broom Brush Replace Rotary Broom Gearbox Rotary Broom Drive Chain Remove Brush from Broom HousingLoosen Chain Idler and Set Screws Replace Drive Chain Remove Chain Guard Loosen Chain TensionRotary Broom Drive Sprocket Sprocket WearAlign Sprockets Check Sprocket Alignment with Chain InstalledRemove and Replace Sprocket Replace Snowblower Gearbox Two-Stage Snowblower Reduction Sprocket Replace Reduction ChainReduction Sprocket Wear Debris Blower Drive BeltDozer Blade Skid Shoes AdjustmentsGauge Wheel Height Adjustment Skid Shoe Height Adjustment Rotary Broom Brush LevelingSide to Side Level Adjustment Rotary Broom Gauge Wheels Proper Drive Chain Tension Two-Stage Snowblower Skid Shoes Loosen Chain Idler NutAnce under the blade. On level, paved surfaces Surface. On uneven or gravel surfaces, allow 1/2Proper Drive Belt Deflection Debris Blower Rotation Pinions Handle Adjustment Drive Belt Tension Adjustment Debris Blower Rotation PinionsTorque Specifications Detach Blade from Implement Hitch Removal and Storage InstructionsRemoval Detach Snowblower from Implement Hitch Detach Rotary Broom from Implement HitchEND of Season Storage Detach Implement Hitch from TractorRotary Broom Fasteners Implement Hitch AssemblyUse only genuine Walker replacement parts RAD Technologies Inc Implement Hitch Electrical ComponentsImplement Hitch Electrical Components Fasteners Implement Hitch Electrical Components Dozer Blade Assembly Dozer Blade Assembly Kit I391 Side Caster Wheels Kit Rotary Broom AssemblyRotary Broom Assembly Rotary Broom Assembly Rotary Broom Drive Components Gearbox AssemblyDriveline and Sprockets Assembly Fasteners Rotary Broom Drive Components Chute Rotation Assembly Snowblower Housing ComponentsSnowblower Mount Assembly Reduction Box AssemblySnowblower Housing Components Driveline and Auger Components Snowblower Drive ComponentsSnowblower Drive Components Debris Blower Components Debris Blower ComponentsDebris Blower Components Debris Blower Manual Rotation Components Debris Blower Manual Rotation ComponentsDebris Blower Manual Rotation Components KEY to Abbreviations Used in Illustrated Parts Manual Limited Warranty For Walker Commercial Rider Mower Walker MFG. CO E. Harmony ROAD, Fort COLLINS, CO 80528 970