Walker RB6650, SB6670 Assembly Instructions, Setup Instructions, Implement Hitch Installation

Page 23

Assembly Instructions

SETUP INSTRUCTIONS

Walker Implements are shipped partially assem- bled. After uncrating the implement adaptor and/or implement(s), initial setup is required.

NOTE: During the process of unpacking, any dam- aged or missing parts should be noted and reported to the delivering carrier immediately (put in writing within 15 days). The carrier will provide directions for proceeding with a claim to receive compensation for damage.

IMPLEMENT HITCH

Implement Hitch Installation

1.Remove the mower deck from the tractor if nec- essary. Refer to the appropriate Tractor Own- er’s Manual.

2.Lightly grease each tractor support arm (2) on the tractor. Refer to Implement Hitch Installa- tion photo for location of tractor support arms.

3.Engage the hitch frame tube sockets on the tractor support arms. Slide the implement hitch onto the support arms approximately 3 in. (76 mm).

4.Install the hitch pin through the hole on the end of each support arm to lock the hitch in place. Two (2) hitch pins are included in the owner’s packet of materials.

Grease Tractor

Support Arms

Hitch Frame

Tube Sockets

Implement Hitch Installation

IMPORTANT: If the tractor body needs to be raised, the PTO shield must be in the closed or down po- sition and the implement must be in the lowered position. The only time the PTO shield needs to be open or raised is when connecting or disconnecting the driveline for the rotary broom, snowblower, or debris blower.

Hitch Pins Lock Hitch on Support Arms

PTO Shield

in CLOSED

Position

PTO Shield in CLOSED Position

5.Loosen the 3/4-10 jam nut on the end of the im- plement Hitch. Adjust the 3/4-10 x 2 in. hex bolt until it contacts the cross-member of the tractor frame. Securely tighten the 3/4-10 jam nut to prevent the bolt from moving.

3/4 - 10 x 2"

Hex Bolt3/4 - 10 Jam Nut

Implement Hitch Jam Nut Adjustment

IMPORTANT: This adjustment will need to be made only once if the same tractor and hitch are used together. If the hitch will be used on more than one tractor, this adjustment will be required every time the hitch is mounted on a different tractor.

19

Image 23
Contents Illustrated Parts Manual Foreword Table of Contents KEY to Abbreviations Used in Illustrated Parts List Maintenance Schedule ChartTorque Specifications Implement Hitch Assembly Electrical ComponentsFill In By Purchaser General InformationGlossary Identifying Number LocationsSerial Number Rotary Broom Serial Number Location Serial NumberUnit Descriptions Rotary Broom SpecificationsImplement Hitch Dozer BladeTWO-STAGE Snowblower Debris Blower Component Identification Implement Hitch Top View Not InstalledDozer Blade Rear View and Right Side View Not Installed Rotary Broom Rear View and Right Side View Not Installed TWO-STAGE Snowblower Two-Stage Snowblower Rear View Not Installed Debris Blower Front View and Left Side View Not Installed Debris Blower Rear View and Right Side View Not Installed Do not operate with bystanders in the area Safety InstructionsBefore Operating Operating Maintenance PTO Shield Walker P/N Attaching Hitch Hitch Mount Adjust SAFETY, CONTROL, and Instruction DecalsSAFETY, CONTROL, and Instruction Decals Implement Hitch Jam Nut Adjustment Assembly InstructionsSetup Instructions Implement Hitch InstallationConnect Harness Wire to Circuit Breaker Drill Holes for Implement Hitch WiringAttach Toggle Switch Mounting Bracket Attach Wiring Harness and Toggle SwitchComplete Implement Hitch Wiring Implement Hitch Wiring Diagram Insert Female Hitch into Blade Attachment Attach Spring to Blade AssemblyInsert Adjustment Pin and Set Blade Angle Attach Blade to Tractor Install Skid ShoesRotary Boom Installation Connect Broom Driveline to Tractor PTO Shaft Prepare Rotary Broom for InstallationAssemble Rotary Broom Driveline Attach Broom to Implement HitchGHS Blower Intake Cover Adjust Brush to Ground ContactLock Stopper Pin in Place Install Plastic Insert over Chute Base Lip Install Hand Guard on ChuteInstall Skid Shoes Snowblower Installation Install Rotation Worm AssemblyInstall Chute over Plastic Insert Mount Female Hitch to Snowblower Install Bolt in Reduction BoxInstall Reduction Box Cover Attach Drive Shaft Yoke to Reduction ShaftInsert Rotation Handle into Rotation Worm Attach Snowblower to Implement HitchConnect Driveline Coupler to Tractor PTO Attach Parallel Bar to Female HitchAttach Debris Blower to Implement Hitch Attach Tractor PTO to Debris Blower Input ShaftRefer to Hitch Locking Lever in Operating Instruc Refer to Angle Adjustment Pin in OperatingRefer to Ground Contact Knob in Operating Refer to Angle Adjustment Lever in OperatingTWO-STAGE Snowblower Operation Operating InstructionsTWO-STAGE Snowblower Controls PTO Clutch Engaged Engaging the SnowblowerThrow Snow to One Side Throw Snow to Both Sides Clogging ChecklistRaising and Lowering the Debris Blower Stopping the Machine Engaging the Debris BlowerTools should be performed by a trained technician Maintenance InstructionsMaintenance procedures requiring special training or Model Service Item Daily HoursRemove Chain Guard Cover LubricationRotary Broom Gearbox Rotary Broom Gearbox with Cover RemovedGrease Fitting and Oil Point Lubrication Snowblower Lubricant Plug LocationTwo-Stage Snowblower Reduction Chain Remove Reduction Box CoverLubrication Implement Hitch Lubrication Points Angle Adjustment Pin Oil Dozer Blade Lubrication Points Ident Rotary Broom Lubrication Points Location Type Two-Stage Snowblower Lubrication Points Ident Lubrication Location Type Debris Blower Lubrication Points Support Rear of Broom Housing REPLACING/REPAIRINGDozer Blade Cutting Edge Replacement Rotary Broom Brush Replace Rotary Broom Gearbox Rotary Broom Drive Chain Remove Brush from Broom HousingLoosen Chain Idler and Set Screws Sprocket Wear Remove Chain Guard Loosen Chain TensionReplace Drive Chain Rotary Broom Drive SprocketAlign Sprockets Check Sprocket Alignment with Chain InstalledRemove and Replace Sprocket Replace Snowblower Gearbox Debris Blower Drive Belt Replace Reduction ChainTwo-Stage Snowblower Reduction Sprocket Reduction Sprocket WearDozer Blade Skid Shoes AdjustmentsGauge Wheel Height Adjustment Skid Shoe Height Adjustment Rotary Broom Brush LevelingSide to Side Level Adjustment Rotary Broom Gauge Wheels Surface. On uneven or gravel surfaces, allow 1/2 Loosen Chain Idler NutProper Drive Chain Tension Two-Stage Snowblower Skid Shoes Ance under the blade. On level, paved surfacesProper Drive Belt Deflection Debris Blower Rotation Pinions Handle Adjustment Drive Belt Tension Adjustment Debris Blower Rotation PinionsTorque Specifications Detach Blade from Implement Hitch Removal and Storage InstructionsRemoval Detach Snowblower from Implement Hitch Detach Rotary Broom from Implement HitchEND of Season Storage Detach Implement Hitch from TractorRotary Broom Fasteners Implement Hitch AssemblyUse only genuine Walker replacement parts RAD Technologies Inc Implement Hitch Electrical ComponentsImplement Hitch Electrical Components Fasteners Implement Hitch Electrical Components Dozer Blade Assembly Dozer Blade Assembly Kit I391 Side Caster Wheels Kit Rotary Broom AssemblyRotary Broom Assembly Rotary Broom Assembly Rotary Broom Drive Components Gearbox AssemblyDriveline and Sprockets Assembly Fasteners Rotary Broom Drive Components Reduction Box Assembly Snowblower Housing ComponentsChute Rotation Assembly Snowblower Mount AssemblySnowblower Housing Components Driveline and Auger Components Snowblower Drive ComponentsSnowblower Drive Components Debris Blower Components Debris Blower ComponentsDebris Blower Components Debris Blower Manual Rotation Components Debris Blower Manual Rotation ComponentsDebris Blower Manual Rotation Components KEY to Abbreviations Used in Illustrated Parts Manual Limited Warranty For Walker Commercial Rider Mower Walker MFG. CO E. Harmony ROAD, Fort COLLINS, CO 80528 970