Woods Equipment FZ28K, FZ23B Starting Engine, Starting Mower or Attachment, Practice Operation

Page 12

The PTO control must be in the “OFF” position and the steering handles in the NEUTRAL position before unit can be started.

A safety switch behind the operator’s seat will cause the engine to stop if the operator leaves the seat with the PTO or steering handles engaged. The engine will also stop if the steering handles are moved from NEU- TRAL while the parking brake is engaged or if the deck jumper wire is not connected to the wire harness or the deck safety switch is disengaged.

STARTING ENGINE

„Do not run engine indoors. Exhaust gases con- tain carbon monoxide, an odorless and deadly poi- son.

To enhance starter life, use short starting cycles not exceeding 10 seconds. If engine does not start within 10 seconds, stop cranking for 30 seconds; then repeat starting procedures.

1.Position yourself on the power unit seat.

2.Set parking brake.

3.Place steering control handles in the NEUTRAL position (pivoted outward).

4.Place PTO switch in the “OFF” position (down).

5.Place throttle approximately 1/3 open.

6.Turn key to “START”.

7.Ensure that the alternator and oil pressure lights are off.

8.Warm up engine several minutes at medium throttle.

NOTE: Choke as necessary to start. When engine starts, release key immediately. Pull choke gradually back until choke is off and engine is running smoothly.

NOTE: Allow engine a warm-up period regardless of the season. Loading a cold engine will shorten its life.

Cold Weather Starting Tips

1.Use proper oil grade for temperature expected. (Refer to engine manual for oil grade.)

2.Set throttle half way open.

3.A warm battery has better starting capacity than a cold one.

4.Use fresh fuel, it is better for starting than leftover fuel.

STARTING MOWER OR ATTACHMENT

„Make sure people and objects are clear of attachment and discharge area before engaging PTO.

NOTICE

Never engage PTO if the mower blades are plugged with grass or other material. This may cause damage to the electric clutch.

1.With engine running, position throttle at half speed.

2.Engage PTO by pulling up on the PTO switch.

3.Move throttle to full speed and begin operation.

NOTE: Starting attachment at lower engine speed will help prolong the life of the clutch and transmission components.

Stopping Mower or Attachment

Push down on PTO switch.

NOTE: If attachment does not stop in five seconds, the unit requires service.

PRACTICE OPERATION

„Never allow children or untrained persons to operate equipment.

Operating this unit is not difficult once you are familiar with the use of the controls. Equip the power unit with the attachment you will be using and practice in a flat open area at half throttle setting until you are comfort- able with the controls.

Do not operate attachment until you become proficient with controls.

Uneven Terrain Operation

„Do not operate on slopes greater than 15 degrees (27% grade).

„Do not stop, start, or change directions sud- denly on slopes.

„Use extreme care and reduce ground speed on slopes and rough terrain.

12 Operation

MAN0875 (2/8/2011)

 

 

Image 12
Contents MOW’N Machinetm Introduction To the DealerTable of Contents Specifications General InformationSafety Safety RulesTraining PreparationTransportation OperationMaintenance Storage Safety & Instructional Decals Replace Immediately If DamagedBe Careful Controls and Switches OperationOperation Starting Engine Starting Mower or AttachmentPractice Operation Steering Handle Operation Steering Handle Positions„ Watch for hidden hazards on the terrain during operation Moving Disabled Power Unit Weight Transfer SystemStopping Engine Owner PRE-OPERATION Check List Owners ResponsibilityOwner Service Owner ServiceService Engine Lubrication InformationTailwheel Maintenance Lubrication DiagramHydrostatic Transmission Service Service BatteryHydraulic Transmission Change OIL & Filter Refer to FigureCleaning Burnish ClutchReturn to Operation After Each UseDealer Service Dealer ServiceTroubleshooting Hydrostatic Pump No Positive Neutral PositionTroubleshooting Engine Engine Dies When Steering Handles are EngagedEngine will not crank Engine cranks but will not startTroubleshooting Deck Safety Switch Hydrostatic Pump InstallationHydrostatic Pump Removal Belt RemovalParking Brake Adjustment Clutch RepairRemove Components Refer to & FigureInstall Clutch Align BeltReassemble Components Clutch & Drive Components Reassembled Assembly AssemblyInstall Drive Tires Adjust Steering HandlesInstall Single Tailwheel Optional Single Tailwheel InstallationDealer Check Lists Dealer Check ListsPRE-DELIVERY Check List Delivery Check ListParts Index Mow’n Machine FZ23B, FZ28K PartsFZ23B, FZ28K Frame Assembly FZ23B, FZ28K Frame Assembly Parts List Part QTY DescriptionFZ23B Engine Assembly FZ23B Engine Assembly Parts List FZ28K Engine Assembly FZ28K Engine Assembly Parts List Hydraulic Reservoir & Hoses Hydraulic Reservoir & Hoses Parts List Hydraulic DiagramPTO, Clutch & Pump Assembly PTO Clutch & Pump Assembly Parts List GR5Seat & Hood Assembly Tailwheel Assembly Single Tailwheel AssemblyWide Stance Tailwheel Assembly Brake Assembly Brake Assembly Parts List Headlight KIT OptionalCounterweight Mount KIT Steering Assembly Diagram FZ23B Wiring FZ23B Wiring Diagram Parts List SN 1177489 & UPFZ28K Wiring Diagram SN 1177489 & UP FZ28K Wiring Diagram Parts List Bolt Torque Chart SAE Series Torque ChartMetric Series Torque Chart AppendixBolt Size Chart AbbreviationsIndex IndexLimited Warranty Mow’n MachineTM Zero-Turn Mowers

FZ23B, FZ28K specifications

Woods Equipment has established itself as a leader in the manufacturing of high-quality agricultural and landscape maintenance equipment. Among its notable innovations are the FZ28K and FZ23B models, designed for immense versatility and efficiency in various applications.

The Woods FZ28K is known for its robust construction and powerful performance. This model features a 28-inch cutting deck, making it ideal for large-scale mowing tasks. The FZ28K is equipped with a high-performance engine designed for durability and reliability, allowing operators to tackle tough terrain with ease. Its advanced cutting technology ensures a clean and even cut, promoting healthier grass growth. Enhanced maneuverability is achieved through its compact design, allowing users to navigate tight spaces effortlessly.

On the other hand, the FZ23B model is built for versatility and ease of use in a multitude of applications. With a 23-inch cutting deck, it is perfect for both residential and commercial properties. The FZ23B prioritizes user comfort, featuring an ergonomic design and intuitive controls that reduce operator fatigue during extended use. Its lightweight structure does not compromise strength, making it nimble enough for intricate mowing tasks while remaining sturdy for larger areas.

Both models utilize cutting-edge technology that optimizes power and efficiency. Featuring adjustable cutting heights, operators can customize their mowing experience, ensuring the best results for their specific lawn conditions. The advanced engine technology in both the FZ28K and FZ23B models ensures reduced emissions, contributing to environmentally friendly operation while still delivering excellent performance.

Another key characteristic of Woods Equipment’s offerings is their ease of maintenance. Both models come with accessible service points, allowing users to perform routine maintenance with minimal effort. This focus on user experience extends to the design of the mower decks, which are constructed for easy cleaning and upkeep.

In conclusion, the Woods Equipment FZ28K and FZ23B mowers represent the perfect blend of power, efficiency, and user-centric design. Their advanced features and technologies empower operators to achieve professional-grade results while ensuring comfort and ease of use. Whether mowing large pastures or manicuring residential lawns, the Woods FZ series stands ready to meet diverse landscaping needs, solidifying Woods Equipment’s reputation for excellence in outdoor power tools.