Woods Equipment BW126Q-3, BW180Q-3, BW126-3 manual PRE-OPERATION Check List, Owners Responsibility

Page 18

STORAGE

Follow these steps when storing your cutter:

1.Clean cutter before storing. See page 23 for cleaning instructions. Store on level, solid ground.

2.Disconnect driveline and secure up off the ground.

3.Lower wings to ground.

4.Raise cutter center section and pin transport bar in raised position.

5.Attach parking jack and raise tongue weight off tractor drawbar.

6.Place wedge blocks at front and rear of wheels on center section and each wing to prevent wheel rotation.

7.Securely block all four corners of center section and each wing with jack stands.

8.Remove hydraulic hoses after tractor is turned off and all system pressure is released by operating valve levers several times.

9.Remove safety tow chain.

10.Remove retainer pin and high strength drawbar pin.

11.Keep children and bystanders away from storage area.

PRE-OPERATION CHECK LIST

(OWNER'S RESPONSIBILITY)

___ Review and follow all safety rules and safety decal instructions on page 7 through page 13.

___ Check that all safety decals are installed and in good condition. Replace if damaged.

___ Check that equipment is properly and securely attached to tractor.

___ Make sure driveline spring-activated locking pin or collar slides freely and is seated firmly in trac- tor PTO spline groove.

___ Check all lubrication points and grease as instructed in lubrication information. Make sure

 

the PTO slip joint is lubricated and that the gear-

 

box fluid levels are correct.

___

Set tractor PTO at correct rpm for your equip-

 

ment.

___

Lubricate all grease fitting locations. Make sure

 

PTO shaft slip joint is lubricated.

___

Check that all hydraulic hoses and fittings are in

 

good condition and not leaking before starting

 

tractor. Check that hoses are not twisted, bent

 

sharply, kinked, frayed, or pulled tight. Replace

 

any damaged hoses immediately.

___

Check that all hardware is properly installed and

 

secured.

___

Check cutting height and attitude adjustment.

___

Raise and lower equipment to make sure air is

 

purged from hydraulic cylinders and hoses. Raise

 

and lower equipment to make sure air is purged

 

from hydraulic cylinders and hoses.

___

Check that blades are sharp and secure and cut-

 

ting edge is positioned to lead in a counterclock-

 

wise rotation.

___

Make sure tractor ROPS or ROPS cab and seat

 

belt are in good condition. Keep seat belt

 

securely fastened during operation.

___ Check that shields and guards are properly installed and in good condition. Replace if dam- aged.

___ Before starting engine, operator must be in trac- tor seat with seat belt fastened. Place transmis- sion in neutral or park, engage brake and disengage tractor PTO.

___ Inspect area to be cut and remove stones, branches, or other hard objects that might be

 

thrown and cause injury or damage.

___

Inspect rubber or chain shielding and replace any

 

damaged rubber shield or missing links.

___

Make sure tractor 3-point lift links do not interfere

 

with hydraulic hoses or driveline throughout full

 

turning range.

18 Operation

MAN0707 (5/30/2008)

 

Page 17 Page 19
Image 18
Page 17 Page 19
Contents Batwing Introduction To the DealerTable of Contents LEA EL InstructivoBW180-3 / BW180Q-3 BW126-3 / BW126Q-3 SpecificationsGeneral Information BW180-3 BW180Q-3 BW126-3 BW126Q-3Free Mower Safety Video SafetyTraining Package for Rotary Mowers/Cutters-English Training Package for Rotary Mowers/Cutters-English/SpanishTraining Safety RulesInstallation PreparationTransportation OperationMaintenance Storage Safety & Instructional Decals Be CarefulPN 1006348 Located on Wheel Rims 1000 RPM PN 15922 1000 RPM PN 18866 540 RPMSafety Operation Connecting Cutter to TractorOperation Hydraulic ConnectionCV Driveline Turning Limits Cutting Height AdjustmentInterference Check Tractor OperationCutter Operation Mowing TipsShredding Wing Lock-Up TransportingLock-Up Center Section Lock-UpPRE-OPERATION Check List Owners ResponsibilityOwner Service Owner ServiceBlocking Method Lubrication Gearbox LubricationDriveline Lubrication Blades Blade Installation FigureSeasonal Lubrication Blade Removal FigureSlip Clutch Adjustment Figure Blade SharpeningCleaning Shielding RepairServicing Tires Safely Troubleshooting TroubleshootingGearbox Maintenance Dealer ServiceDealer Service Seal Replacement FigureDisassembly Figure Gearbox RepairRemoval from Cutter Figure Reinstallation GearboxDisassembly AssemblySplitter Gearbox Repair Figure Removal from Cutter Reinstallation on Cutter Check GearboxCrossbar Removal Crossbar RemovalCrossbar Installation Joint DisassemblyUniversal Joint Repair Joint Assembly Assembly Assembly InstructionsDealer SET-UP Instructions Install Height Adjustment Cylinder Install SMV EmblemInstall Wheel and Hub Install TongueInstall 3-Joint Drive 540 RPM Only Joint Drive InstallationInstall CV Drive Optional Install WingInstall Wing Cylinder & Lock-up Bar Install Wing Wheel and Hub Figure Left Wing Lock-Up Bar InstalledInstall Wing Wheel Yoke Adjustment Link Install Wing DrivelineInstall Hose Kit Install Chain or Belt Shielding Chain Shielding Installation Center SectionChain Shielding Installation Right Wing Shown Belt Shielding Installation Right Wing BW126 and BW126L Counterweight Installation Refer to FigureWinch Kit Installation Optional PRE-DELIVERY Check List Dealer Check ListsDealer Check Lists Delivery Check ListMAN0707 5/30/2008 Parts Index PartsMain Frame Assembly Front Section Part QTY Description Main Frame Assembly Rear Section Tire & hub see Wing Assembly See Splitter Gearbox Assembly Gear, 540 rpm Wing & Center Gearbox Assembly 540 RPM 1000 RPM Center Deck Drive Assembly BW180 & BW126 Front Drive Assembly Equal Angle BW180 & BW126 Rear Drive Assembly Equal Angle RPM & 1000 RPM Front CV Drive Wing Drive Assembly Bolt Wheel & Tire Assembly 1027468 1028590 Chain Shielding Center Section Front & Rear Single ROW Double ROWChain Shielding Wing Front & Rear Single ROWHydraulic Cylinders Crossbar Puller Optional Hydraulic Cylinder Stroke Control KITBW126 / BW126Q Weight BOX Assembly Optional Winch Kit Installation Winch KIT OptionalWinch Kit Operation Appendix Bolt Torque ChartSAE Series Torque Chart Metric SeriesBolt Size Chart AbbreviationsIndex IndexWarranty Warranty

BW180-3, BW126Q-3, BW126-3, BW180Q-3 specifications

Woods Equipment Company has long been a leader in manufacturing innovative agricultural and landscape maintenance products. Among its popular offerings are the BW180-3, BW180Q-3, BW126-3, and BW126Q-3 models, which are designed to meet the needs of both professional and amateur users.

The BW180-3 is an impressive rotary cutter with a cutting width of 60 inches, making it ideal for tackling overgrown fields, pastures, and other large mowing areas. It features a rugged, all-steel construction that ensures durability and longevity, even in the toughest of conditions. The cutter is equipped with a heavy-duty gearbox, ensuring efficient power transfer while minimizing wear and tear. The innovative design of the BW180-3 also includes an adjustable tail wheel that provides stability and ease of maneuverability.

For those seeking advanced functionality, the BW180Q-3 model introduces quick-attach capabilities, allowing users to easily connect and disconnect the cutter from the tractor without the need for additional tools. This feature not only saves time but also enhances user convenience, making it an excellent choice for busy farms and landscaping operations. With a similar cutting width as the BW180-3, this model maintains the robust construction and drivetrain specifications that make Woods Equipment cutters a trusted choice.

On the smaller side, the BW126-3 offers a 48-inch cutting width, perfect for maintaining smaller fields and lawn areas. Designed with the same enduring quality, it is lightweight yet powerful enough to handle tough mowing tasks. The BW126-3 comes with a versatile hitch design that makes it compatible with a wide range of tractors.

The BW126Q-3 shares the core features of the BW126-3 but incorporates the quick-attach technology for enhanced user efficiency. This model combines flexibility with reliability and is particularly suited for operators who need to switch quickly between attachments throughout their workday.

Overall, the Woods Equipment BW180-3, BW180Q-3, BW126-3, and BW126Q-3 models provide a variety of features and technologies that make them indispensable for anyone looking to efficiently manage land. Whether you need the extra cutting width and power of the BW180 series or the nimble ease of the BW126 series, Woods Equipment offers versatile solutions for diverse agricultural and landscaping needs.
Top Page Image Contents