Woods Equipment BW180-3, BW180Q-3, BW126-3, BW126Q-3 manual Owner Service, Blocking Method

Page 19

OWNER SERVICE

The information in this section is written for operators who possess basic mechanical skills. If you need help, your dealer has trained service technicians available. For your protection, read and follow the safety informa- tion in this manual.

Keep all persons away from operator control area while performing adjustments, service, or maintenance.

Before working underneath, disconnect drive- line from tractor, lower wings to ground, raise cut- ter, and pin transport bar in raised position. Attach parking jack and lower to ground. Securely block all four corners of center section and each wing with jack stands. Blocking up prevents the cutter from dropping due to hydraulic leak down, hydrau- lic system failure, or mechanical component fail- ure.

Service and maintenance work not covered in OWNER SERVICE must be done by a qualified dealership. Special skills, tools, and safety proce- dures may be required. Failure to follow these instructions can result in serious injury or death.

Before servicing, adjusting, repairing or unplug- ging, stop tractor engine, place all controls in neu- tral, set park brake, remove ignition key, and wait for all moving parts to stop.

Never perform service or maintenance with engine running.

CAUTION

If you do not understand any part of this manual and need assistance, see your dealer.

Always wear relatively tight and belted clothing to avoid entanglement in moving parts. Wear sturdy, rough-soled work shoes and protective equipment for eyes, hair, hands, hearing, and head; and respirator or filter mask where appropriate.

BLOCKING METHOD

To minimize the potential hazards of working under- neath the cutter, follow these procedures:

Before performing any service or maintenance, lower equipment to ground or block securely, turn off engine, remove key, and disconnect driveline from tractor PTO.

Never go underneath equipment (lowered to the ground or raised) unless it is properly blocked and secured. Never place any part of the body under- neath equipment or between moveable parts even when the engine has been turned off. Hydraulic system leak down, hydraulic system failures, mechanical failures, or movement of control levers can cause equipment to drop or rotate unexpect- edly and cause severe injury or death. Follow Oper- ator's Manual instructions for working underneath and blocking requirements or have work done by a qualified dealer.

Do not position jackstands under wheels, axles, or wheel supports. Components can rotate and cause cut- ter to fall.

1.Jackstands with a load rating of 1000 lbs. or more are the only approved blocking device for this cutter. Install jackstands (shown by Xs in Figure 5) under the cutter before working underneath unit.

2.Consider the overall stability of the blocked unit. Just placing jackstands underneath will not ensure your safety.

The working surface must be level and solid to support the weight on the jackstands. Make sure jackstands are stable, both top and bottom. Make sure cutter is approximately level.

3.With full cutter weight lowered onto jackstands, test blocking stability before working underneath.

4.If cutter is attached to tractor when blocking, set the brakes, remove key, and block cutter before working underneath.

5.Securely block rear tractor wheels, in front and behind. Tighten tractor lower 3-point arm anti-sway mechanism to prevent side-to-side movement.

MAN0707 (5/30/2008)

Owner Service 19

 

 

Page 18 Page 20
Image 19
Page 18 Page 20
Contents Batwing To the Dealer IntroductionLEA EL Instructivo Table of ContentsBW180-3 BW180Q-3 BW126-3 BW126Q-3 SpecificationsGeneral Information BW180-3 / BW180Q-3 BW126-3 / BW126Q-3Safety Free Mower Safety VideoTraining Package for Rotary Mowers/Cutters-English/Spanish Training Package for Rotary Mowers/Cutters-EnglishPreparation Safety RulesInstallation TrainingOperation TransportationMaintenance Storage Be Careful Safety & Instructional DecalsPN 1006348 Located on Wheel Rims PN 15922 1000 RPM PN 18866 540 RPM 1000 RPMSafety Hydraulic Connection Connecting Cutter to TractorOperation OperationTractor Operation Cutting Height AdjustmentInterference Check CV Driveline Turning LimitsMowing Tips Cutter OperationShredding Center Section Lock-Up TransportingLock-Up Wing Lock-UpOwners Responsibility PRE-OPERATION Check ListOwner Service Owner ServiceBlocking Method Gearbox Lubrication LubricationDriveline Lubrication Blade Removal Figure Blade Installation FigureSeasonal Lubrication BladesBlade Sharpening Slip Clutch Adjustment FigureShielding Repair CleaningServicing Tires Safely Troubleshooting TroubleshootingSeal Replacement Figure Dealer ServiceDealer Service Gearbox MaintenanceGearbox Repair Disassembly FigureRemoval from Cutter Figure Gearbox ReinstallationAssembly DisassemblySplitter Gearbox Repair Figure Removal from Cutter Check Gearbox Reinstallation on CutterCrossbar Removal Crossbar RemovalJoint Disassembly Crossbar InstallationUniversal Joint Repair Joint Assembly Assembly Instructions AssemblyDealer SET-UP Instructions Install SMV Emblem Install Height Adjustment CylinderInstall Tongue Install Wheel and HubJoint Drive Installation Install 3-Joint Drive 540 RPM OnlyInstall Wing Install CV Drive OptionalInstall Wing Cylinder & Lock-up Bar Left Wing Lock-Up Bar Installed Install Wing Wheel and Hub FigureInstall Wing Driveline Install Wing Wheel Yoke Adjustment LinkInstall Hose Kit Chain Shielding Installation Center Section Install Chain or Belt ShieldingChain Shielding Installation Right Wing Shown Belt Shielding Installation Right Wing Refer to Figure BW126 and BW126L Counterweight InstallationWinch Kit Installation Optional Delivery Check List Dealer Check ListsDealer Check Lists PRE-DELIVERY Check ListMAN0707 5/30/2008 Parts Parts IndexMain Frame Assembly Front Section Part QTY Description Main Frame Assembly Rear Section Tire & hub see Wing Assembly See Splitter Gearbox Assembly Gear, 540 rpm Wing & Center Gearbox Assembly 540 RPM 1000 RPM Center Deck Drive Assembly BW180 & BW126 Front Drive Assembly Equal Angle BW180 & BW126 Rear Drive Assembly Equal Angle RPM & 1000 RPM Front CV Drive Wing Drive Assembly Bolt Wheel & Tire Assembly 1027468 1028590 Single ROW Double ROW Chain Shielding Center Section Front & RearSingle ROW Chain Shielding Wing Front & RearHydraulic Cylinders Hydraulic Cylinder Stroke Control KIT Crossbar Puller OptionalBW126 / BW126Q Weight BOX Assembly Optional Winch KIT Optional Winch Kit InstallationWinch Kit Operation Metric Series Bolt Torque ChartSAE Series Torque Chart AppendixAbbreviations Bolt Size ChartIndex IndexWarranty Warranty

BW180-3, BW126Q-3, BW126-3, BW180Q-3 specifications

Woods Equipment Company has long been a leader in manufacturing innovative agricultural and landscape maintenance products. Among its popular offerings are the BW180-3, BW180Q-3, BW126-3, and BW126Q-3 models, which are designed to meet the needs of both professional and amateur users.

The BW180-3 is an impressive rotary cutter with a cutting width of 60 inches, making it ideal for tackling overgrown fields, pastures, and other large mowing areas. It features a rugged, all-steel construction that ensures durability and longevity, even in the toughest of conditions. The cutter is equipped with a heavy-duty gearbox, ensuring efficient power transfer while minimizing wear and tear. The innovative design of the BW180-3 also includes an adjustable tail wheel that provides stability and ease of maneuverability.

For those seeking advanced functionality, the BW180Q-3 model introduces quick-attach capabilities, allowing users to easily connect and disconnect the cutter from the tractor without the need for additional tools. This feature not only saves time but also enhances user convenience, making it an excellent choice for busy farms and landscaping operations. With a similar cutting width as the BW180-3, this model maintains the robust construction and drivetrain specifications that make Woods Equipment cutters a trusted choice.

On the smaller side, the BW126-3 offers a 48-inch cutting width, perfect for maintaining smaller fields and lawn areas. Designed with the same enduring quality, it is lightweight yet powerful enough to handle tough mowing tasks. The BW126-3 comes with a versatile hitch design that makes it compatible with a wide range of tractors.

The BW126Q-3 shares the core features of the BW126-3 but incorporates the quick-attach technology for enhanced user efficiency. This model combines flexibility with reliability and is particularly suited for operators who need to switch quickly between attachments throughout their workday.

Overall, the Woods Equipment BW180-3, BW180Q-3, BW126-3, and BW126Q-3 models provide a variety of features and technologies that make them indispensable for anyone looking to efficiently manage land. Whether you need the extra cutting width and power of the BW180 series or the nimble ease of the BW126 series, Woods Equipment offers versatile solutions for diverse agricultural and landscaping needs.
Top Page Image Contents