Woods Equipment BW126Q-3 manual Install Wing Wheel and Hub Figure, Left Wing Lock-Up Bar Installed

Page 38

2.Slide spacer (17) and lock-up bar (19) over clevis pin (22) on back side of cylinder lug & secure with washer (27) and cotter pins (66).

3.Attach base end of wing cylinder (4) to cylinder links (23 & 24) using clevis pin (18) and cotter pins (66).

4.Remove plug from base end of hydraulic cylinder. Align cylinder rod end with cylinder lug on the wing and insert lock-up pin (26).

5.Slide spacer (25) over lock-up pin (26) on back side of cylinder rod and secure with cotter pins (66).

6.Insert safety pin (45) into the end of lock-up pin (26). The safety pin will secure lock-up bar into position when wing is in the UP position.

7.Extend cylinder fully & replace plug in base end of cylinder. This trapped air will help push wing down.

8.Install bushing (40), elbow, (41) and hose (42) to the rod end of cylinder (4). See Install Hose Kit, page 39 for complete instructions.

9.Repeat procedure for opposite wing.

NOTE: (BW126R has only the right wing installed. BW126L has only the left wing installed.)

23

24

19

 

 

 

22

 

 

 

66

 

17

 

 

 

 

 

DP3

 

 

 

 

17.

Spacer, 1"

23.

Cylinder link

19.

Wing lock-up bar

24.

Cylinder link

22.

Headless pin,

66.

Cotter pin,

 

1 x 4.08

 

1/4 x 1-1/2

Figure 32. Left Wing Lock-Up Bar Installed

Install Wing Wheel and Hub (Figure 33)

1.Insert wheel hub into wing wheel yoke arms (6) and align holes.

2.Secure into position using cap screw (54) and flanged lock nut (55).

3.Attach wheel to hub using five lug nuts. Install the chamfered side of the lug nut toward the inside for steel rim for pneumatic tires and rims. Tighten to 75 lbs-ft. Check that tire air pressure is a maximum of 40 psi.

NOTE: Install the flat side of the nut toward the inside for solid tires and aircraft tires (shown).

4.Install optional dual wheel and hub to inside of wheel yoke arm.

NOTE: Pneumatic (BW180 and BW180Q only), notat, and airplane tires are available for this cutter. See page 63 for parts list.

6.Wing wheel yoke arm, right

21. Wheel and hub

39.1/2 NC x 3 HHCS GR5

40.1/2 NC Flanged lock nut

Figure 33. Wing Wheel and Hub Installation - Right

38 Assembly

MAN0707 (5/30/2008)

 

 

Page 37 Page 39
Image 38
Page 37 Page 39
Contents Batwing Introduction To the DealerTable of Contents LEA EL InstructivoBW180-3 / BW180Q-3 BW126-3 / BW126Q-3 SpecificationsGeneral Information BW180-3 BW180Q-3 BW126-3 BW126Q-3Free Mower Safety Video SafetyTraining Package for Rotary Mowers/Cutters-English Training Package for Rotary Mowers/Cutters-English/SpanishTraining Safety RulesInstallation PreparationTransportation OperationMaintenance Storage PN 1006348 Located on Wheel Rims Safety & Instructional DecalsBe Careful 1000 RPM PN 15922 1000 RPM PN 18866 540 RPMSafety Operation Connecting Cutter to TractorOperation Hydraulic ConnectionCV Driveline Turning Limits Cutting Height AdjustmentInterference Check Tractor OperationShredding Cutter OperationMowing Tips Wing Lock-Up TransportingLock-Up Center Section Lock-UpPRE-OPERATION Check List Owners ResponsibilityBlocking Method Owner ServiceOwner Service Driveline Lubrication LubricationGearbox Lubrication Blades Blade Installation FigureSeasonal Lubrication Blade Removal FigureSlip Clutch Adjustment Figure Blade SharpeningServicing Tires Safely CleaningShielding Repair Troubleshooting TroubleshootingGearbox Maintenance Dealer ServiceDealer Service Seal Replacement FigureRemoval from Cutter Figure Disassembly FigureGearbox Repair Reinstallation GearboxSplitter Gearbox Repair Figure Removal from Cutter DisassemblyAssembly Reinstallation on Cutter Check GearboxCrossbar Removal Crossbar RemovalUniversal Joint Repair Crossbar InstallationJoint Disassembly Joint Assembly Dealer SET-UP Instructions AssemblyAssembly Instructions Install Height Adjustment Cylinder Install SMV EmblemInstall Wheel and Hub Install TongueInstall 3-Joint Drive 540 RPM Only Joint Drive InstallationInstall Wing Cylinder & Lock-up Bar Install CV Drive OptionalInstall Wing Install Wing Wheel and Hub Figure Left Wing Lock-Up Bar InstalledInstall Hose Kit Install Wing Wheel Yoke Adjustment LinkInstall Wing Driveline Install Chain or Belt Shielding Chain Shielding Installation Center SectionChain Shielding Installation Right Wing Shown Belt Shielding Installation Right Wing BW126 and BW126L Counterweight Installation Refer to FigureWinch Kit Installation Optional PRE-DELIVERY Check List Dealer Check ListsDealer Check Lists Delivery Check ListMAN0707 5/30/2008 Parts Index PartsMain Frame Assembly Front Section Part QTY Description Main Frame Assembly Rear Section Tire & hub see Wing Assembly See Splitter Gearbox Assembly Gear, 540 rpm Wing & Center Gearbox Assembly 540 RPM 1000 RPM Center Deck Drive Assembly BW180 & BW126 Front Drive Assembly Equal Angle BW180 & BW126 Rear Drive Assembly Equal Angle RPM & 1000 RPM Front CV Drive Wing Drive Assembly Bolt Wheel & Tire Assembly 1027468 1028590 Chain Shielding Center Section Front & Rear Single ROW Double ROWChain Shielding Wing Front & Rear Single ROWHydraulic Cylinders Crossbar Puller Optional Hydraulic Cylinder Stroke Control KITBW126 / BW126Q Weight BOX Assembly Optional Winch Kit Operation Winch Kit InstallationWinch KIT Optional Appendix Bolt Torque ChartSAE Series Torque Chart Metric SeriesBolt Size Chart AbbreviationsIndex IndexWarranty Warranty

BW180-3, BW126Q-3, BW126-3, BW180Q-3 specifications

Woods Equipment Company has long been a leader in manufacturing innovative agricultural and landscape maintenance products. Among its popular offerings are the BW180-3, BW180Q-3, BW126-3, and BW126Q-3 models, which are designed to meet the needs of both professional and amateur users.

The BW180-3 is an impressive rotary cutter with a cutting width of 60 inches, making it ideal for tackling overgrown fields, pastures, and other large mowing areas. It features a rugged, all-steel construction that ensures durability and longevity, even in the toughest of conditions. The cutter is equipped with a heavy-duty gearbox, ensuring efficient power transfer while minimizing wear and tear. The innovative design of the BW180-3 also includes an adjustable tail wheel that provides stability and ease of maneuverability.

For those seeking advanced functionality, the BW180Q-3 model introduces quick-attach capabilities, allowing users to easily connect and disconnect the cutter from the tractor without the need for additional tools. This feature not only saves time but also enhances user convenience, making it an excellent choice for busy farms and landscaping operations. With a similar cutting width as the BW180-3, this model maintains the robust construction and drivetrain specifications that make Woods Equipment cutters a trusted choice.

On the smaller side, the BW126-3 offers a 48-inch cutting width, perfect for maintaining smaller fields and lawn areas. Designed with the same enduring quality, it is lightweight yet powerful enough to handle tough mowing tasks. The BW126-3 comes with a versatile hitch design that makes it compatible with a wide range of tractors.

The BW126Q-3 shares the core features of the BW126-3 but incorporates the quick-attach technology for enhanced user efficiency. This model combines flexibility with reliability and is particularly suited for operators who need to switch quickly between attachments throughout their workday.

Overall, the Woods Equipment BW180-3, BW180Q-3, BW126-3, and BW126Q-3 models provide a variety of features and technologies that make them indispensable for anyone looking to efficiently manage land. Whether you need the extra cutting width and power of the BW180 series or the nimble ease of the BW126 series, Woods Equipment offers versatile solutions for diverse agricultural and landscaping needs.
Top Page Image Contents