Woods Equipment BW126-3, BW180Q-3, BW126Q-3, BW180-3 manual Maintenance

Page 9

SAFETY RULES

ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED!

Do not operate or transport equipment while under the influence of alcohol or drugs.

Operate only in daylight or good artificial light.

Keep hands, feet, hair, and clothing away from equipment while engine is running. Stay clear of all moving parts.

Always comply with all state and local lighting and marking requirements.

Never allow riders on power unit or attachment.

Power unit must be equipped with ROPS or ROPS cab and seat belt. Keep seat belt securely fastened. Falling off power unit can result in death from being run over or crushed. Keep foldable ROPS system in “locked up” position at all times.

Always sit in power unit seat when operating controls or starting engine. Securely fasten seat belt, place transmission in neutral, engage brake, and ensure all other controls are disengaged before starting power unit engine.

Operate tractor PTO at 540 RPM (1000 RPM on Q Series cutters). Do not exceed.

Raise or lower wings slowly to prevent personal injury or damage to cutter.

Connect PTO driveline directly to power unit PTO shaft. Never use adapter sleeves or adapter shafts. Adapters can cause driveline failures due to incorrect spline or incorrect operating length and can result in personal injury or death.

Look down and to the rear and make sure area is clear before operating in reverse.

Do not operate or transport on steep slopes.

Do not stop, start, or change directions sud- denly on slopes.

Watch for hidden hazards on the terrain during operation.

Stop power unit and equipment immediately upon striking an obstruction. Turn off engine, remove key, inspect, and repair any damage before resuming operation.

Continuous operation while the clutch is slip- ping could cause heat build-up resulting in fire. Adjust slip clutch pressure by tightening springs to the dimension shown in the “Owner Service” sec- tion. If clutch is set to minimum spring length, replace the friction disks as shown.

On pull-type or semi-mounted units with optional hydraulic cutting height adjustment, use a single-acting cylinder with a maximum extended

length of 28-1/4" (718 mm) from attaching point center to center.

MAINTENANCE

Before servicing, adjusting, repairing or unplug- ging, stop tractor engine, place all controls in neu- tral, set park brake, remove ignition key, and wait for all moving parts to stop.

Before dismounting power unit or performing any service or maintenance, follow these steps: disengage power to equipment, lower the 3-point hitch and all raised components to the ground, operate valve levers to release any hydraulic pres- sure, set parking brake, stop engine, remove key, and unfasten seat belt.

Before working underneath, disconnect driveline from tractor, lower wings to ground, raise cutter, and pin transport bar in raised position. Attach park- ing jack and lower to ground. Securely block all four corners of center section and each wing with jack- stands. Blocking up prevents the cutter from drop- ping due to hydraulic leak down, hydraulic system failure, or mechanical component failure.

Do not modify or alter or permit anyone else to modify or alter the equipment or any of its compo- nents in any way.

Your dealer can supply original equipment hydraulic accessories and repair parts. Substitute parts may not meet original equipment specifica- tions and may be dangerous.

To prevent contamination during maintenance and storage, clean and then cover hose ends, fit- tings, and hydraulic ports with tape.

Do not allow bystanders in the area when oper- ating, attaching, removing, assembling, or servic- ing equipment.

Never go underneath equipment (lowered to the ground or raised) unless it is properly blocked and secured. Never place any part of the body under- neath equipment or between moveable parts even when the engine has been turned off. Hydraulic system leak down, hydraulic system failures, mechanical failures, or movement of control levers can cause equipment to drop or rotate unexpect- edly and cause severe injury or death. Follow Oper- ator's Manual instructions for working underneath and blocking requirements or have work done by a qualified dealer.

(Safety Rules continued on next page)

BW180_ SR (Rev. 12/10/2007)

Safety 9

Image 9
Contents Batwing To the Dealer IntroductionLEA EL Instructivo Table of ContentsGeneral Information SpecificationsBW180-3 / BW180Q-3 BW126-3 / BW126Q-3 BW180-3 BW180Q-3 BW126-3 BW126Q-3Safety Free Mower Safety VideoTraining Package for Rotary Mowers/Cutters-English/Spanish Training Package for Rotary Mowers/Cutters-EnglishInstallation Safety RulesTraining PreparationOperation TransportationMaintenance Storage Safety & Instructional Decals Be CarefulPN 1006348 Located on Wheel Rims PN 15922 1000 RPM PN 18866 540 RPM 1000 RPMSafety Operation Connecting Cutter to TractorOperation Hydraulic ConnectionInterference Check Cutting Height AdjustmentCV Driveline Turning Limits Tractor OperationCutter Operation Mowing TipsShredding Lock-Up TransportingWing Lock-Up Center Section Lock-UpOwners Responsibility PRE-OPERATION Check ListOwner Service Owner ServiceBlocking Method Lubrication Gearbox LubricationDriveline Lubrication Seasonal Lubrication Blade Installation FigureBlades Blade Removal FigureBlade Sharpening Slip Clutch Adjustment FigureCleaning Shielding RepairServicing Tires Safely Troubleshooting TroubleshootingDealer Service Dealer ServiceGearbox Maintenance Seal Replacement FigureDisassembly Figure Gearbox RepairRemoval from Cutter Figure Gearbox ReinstallationDisassembly AssemblySplitter Gearbox Repair Figure Removal from Cutter Check Gearbox Reinstallation on CutterCrossbar Removal Crossbar RemovalCrossbar Installation Joint DisassemblyUniversal Joint Repair Joint Assembly Assembly Assembly InstructionsDealer SET-UP Instructions Install SMV Emblem Install Height Adjustment CylinderInstall Tongue Install Wheel and HubJoint Drive Installation Install 3-Joint Drive 540 RPM OnlyInstall CV Drive Optional Install WingInstall Wing Cylinder & Lock-up Bar Left Wing Lock-Up Bar Installed Install Wing Wheel and Hub FigureInstall Wing Wheel Yoke Adjustment Link Install Wing DrivelineInstall Hose Kit Chain Shielding Installation Center Section Install Chain or Belt ShieldingChain Shielding Installation Right Wing Shown Belt Shielding Installation Right Wing Refer to Figure BW126 and BW126L Counterweight InstallationWinch Kit Installation Optional Dealer Check Lists Dealer Check ListsPRE-DELIVERY Check List Delivery Check ListMAN0707 5/30/2008 Parts Parts IndexMain Frame Assembly Front Section Part QTY Description Main Frame Assembly Rear Section Tire & hub see Wing Assembly See Splitter Gearbox Assembly Gear, 540 rpm Wing & Center Gearbox Assembly 540 RPM 1000 RPM Center Deck Drive Assembly BW180 & BW126 Front Drive Assembly Equal Angle BW180 & BW126 Rear Drive Assembly Equal Angle RPM & 1000 RPM Front CV Drive Wing Drive Assembly Bolt Wheel & Tire Assembly 1027468 1028590 Single ROW Double ROW Chain Shielding Center Section Front & RearSingle ROW Chain Shielding Wing Front & RearHydraulic Cylinders Hydraulic Cylinder Stroke Control KIT Crossbar Puller OptionalBW126 / BW126Q Weight BOX Assembly Optional Winch Kit Installation Winch KIT OptionalWinch Kit Operation SAE Series Torque Chart Bolt Torque ChartAppendix Metric SeriesAbbreviations Bolt Size ChartIndex IndexWarranty Warranty

BW180-3, BW126Q-3, BW126-3, BW180Q-3 specifications

Woods Equipment Company has long been a leader in manufacturing innovative agricultural and landscape maintenance products. Among its popular offerings are the BW180-3, BW180Q-3, BW126-3, and BW126Q-3 models, which are designed to meet the needs of both professional and amateur users.

The BW180-3 is an impressive rotary cutter with a cutting width of 60 inches, making it ideal for tackling overgrown fields, pastures, and other large mowing areas. It features a rugged, all-steel construction that ensures durability and longevity, even in the toughest of conditions. The cutter is equipped with a heavy-duty gearbox, ensuring efficient power transfer while minimizing wear and tear. The innovative design of the BW180-3 also includes an adjustable tail wheel that provides stability and ease of maneuverability.

For those seeking advanced functionality, the BW180Q-3 model introduces quick-attach capabilities, allowing users to easily connect and disconnect the cutter from the tractor without the need for additional tools. This feature not only saves time but also enhances user convenience, making it an excellent choice for busy farms and landscaping operations. With a similar cutting width as the BW180-3, this model maintains the robust construction and drivetrain specifications that make Woods Equipment cutters a trusted choice.

On the smaller side, the BW126-3 offers a 48-inch cutting width, perfect for maintaining smaller fields and lawn areas. Designed with the same enduring quality, it is lightweight yet powerful enough to handle tough mowing tasks. The BW126-3 comes with a versatile hitch design that makes it compatible with a wide range of tractors.

The BW126Q-3 shares the core features of the BW126-3 but incorporates the quick-attach technology for enhanced user efficiency. This model combines flexibility with reliability and is particularly suited for operators who need to switch quickly between attachments throughout their workday.

Overall, the Woods Equipment BW180-3, BW180Q-3, BW126-3, and BW126Q-3 models provide a variety of features and technologies that make them indispensable for anyone looking to efficiently manage land. Whether you need the extra cutting width and power of the BW180 series or the nimble ease of the BW126 series, Woods Equipment offers versatile solutions for diverse agricultural and landscaping needs.