Stow STR46SP manual Trowel Arm Adjustment Setup, Re-Assembly

Page 37

STR46SP — MAINTENANCE

Figure 38. Trowel Arm Adjustment Setup

3.Unscrew the locking bolts on the adjustment tool and place the trowel arm into the fixture channel as shown in Figure 39 A thin shim may be required to cover the blade holes on the trowelarm. Makesuretoalignthetroweladjustmentboltwith the fixture adjustment bolt.

1Arm

2Trowel Arm Lever

3Fixture Arm

4Adjustment Bolt

5Distance = .010 Inch

6Adjustment Bolt

7Trowel Arm Adjustment Fixture

8Locking Bolts

9Shim

Figure 39. Trowel Arm Adjustment Fixture Components

4.Use an allen wrench to tighten the locking bolts securing the trowel arm in place.

5.Adjust the bolt "distance" shown in Figure 37 to match one of the arms. The other arms will be adjusted to match this distance.

6.Loosen the locking nut on the trowel arm lever, then turn the trowel arm adjusting bolt until it barely touches (.010") the fixture adjusting bolt.

7.Once the correct adjustment is made, tighten the lock nut on the trowel arm to lock in place.

8.Loosen locking nuts on the adjustment fixture, and remove trowel arm.

9.Repeat steps for the remaining trowel arms.

Re-Assembly

1.Clean and examine the upper/lower wear plates and thrust collar.Examine the entire spider assembly.Wire brush any concreteorrustbuild-up.Ifanyofthespider componentsare found to be damaged or out of round, replace them.

2.Makesurethatthebronzetrowelarmbushingisnotdamage or out of round.Clean the bushing if necessary.If the bronze bushing is damaged or worn, replace it.

3.Reinstall bronze bushing onto trowel arm.

4.Repeat steps 2 -3 for each trowel arm.

5.Make sure that the spring tensioner is in the correct position to exert tension on the trowel arm.

6.Insertalltrowelarmswithleversintospiderplate(withbronze bushingalreadyinstalled)usingcaretoaligngreaseholeon bronze bushing with grease hole fitting on spider plate.

7.Locktrowelarmsinplacebytighteningthehexheadboltwith zerk grease fitting and jam nut.

8.Re-install the blades onto the trowel arms.

9.Install stabilizer ring onto spider assembly.

10.Lubricate all grease points (zerk fittings) with premium "Lithum 12" based grease, conforming to NLG1 Grade #2 consistency.

STR46SP • RIDE-ON POWER TROWEL — OPERATION MANUAL — REV. #1 (08/01/06) — PAGE 37

Page 36 Page 38
Image 37
Page 36 Page 38
Contents STR46SP Page Silicosis Warning STR46SP -TABLE of Contents Wilmington Ave Carson, CA STR46SP Parts Ordering ProceduresMachine layout, location of components, checking of engine STR46SP Training ChecklistDaily PRE-OPERATION Checklist STR46SP Daily PRE-OPERATION ChecklistYou can be Injured if you do not follow these directions STR46SP Safety Message Alert SymbolsAlways wear approved eye and hearing protection Always wear approved respiratory protectionFatigue, illness or taking medicine Do not operate or service thisAlways keep the work area well organized STR46SP Rules for Safe OperationLifting the Ride-On Trowel Secure portable power cables in cable tray with tie wraps Towing Safety PrecautionsBattery Always keep the battery charged. IfEmergencies Maintenance SafetyAlways know the location of the nearest first aid kit Machine Safety Decals STR46SP Operation and Safety DecalsTBD STR46SP Specifications TrowelSTR46 Engine Specifications STR46SP Specifications EngineSTR46SP General Information STR46SP Controls and Indicators STR46SP Controls and Indicators Kohler 27 HP Engine STR46SP Basic EngineMuffler Used to reduce noise and emissions Oil Filler Cap Remove to add engine oilControl Handle Assembly Trowel Pre-Set Up InstructionsSeat Assembly Battery SetupEngine Oil Level Always check engine oil Before Each USE STR46SP Initial START-UPGearbox Oil Level Fuel Gauge Important Information Before You Start STR46SP OperationLeft and Right Control Levers SteeringDaily 8-10 Hours MaintenanceWeekly 30-40 Hours Monthly 100-125 HoursAir Cleaner Daily STR46SP MaintenanceReinstall the air cleaner cover and secure the latches Disassembly and Reassembly Standard Type Air Cleaner Components to CheckMake sure the cooling shrouds are reinstalled Make sure the correct depth airSTR46SP Maintenance Removing the Drive Belt Checking The Drive BeltHave a 3/4 X 1 X 3-1/4 inch wooden block available Installing the Drive Belt Using Replacement Drive Belt Reinstall the spare belt carrier and the drive belt guardWooden Block Spare Drive Belt Replacement Torque Converter/Variable Pitch Pulley Drive Pulley Drive System Theory of OperationClutch How It Works Figure Condition a z Engine IdlingBlade Pitch Matching Blade Pitch for Both Sets of BladesStabilizer Ring Removal Trowel Arm adjustment ProcedureRemove the trowel arm from the spider plate Trowel Arm RemovalTrowel Blade Removal Spider Plate Hex Head Bolt Zerk FittingChecking Trowel Arm Straightness Trowel Arm AdjustmentRe-Assembly Trowel Arm Adjustment SetupDecommissioning Trowel/Components Installing Pans Onto Finisher BladesSTR46SP -TROUBLESHOOTING Engine Engine Lacks PowerEngine Overheats Engine Will NotTroubleshooting STR46SP -TROUBLESHOOTING TrowelSTR46SP -TROUBLESHOOTING Trowel STR46SP Notes NO. Column STR46SP Explanation of Code in Remarks ColumnPart NO. Column QTY. Column2829 2149511903 11904Nameplate and Decals STR46SP Nameplate and DecalsDECAL, Powder Coated DECAL, Spring SafetyDECAL, Stow DECAL, AL Pitch RHPivot ASSY. RIGHT/LEFT STR46SP Pivot ASSY. RIGHT/LEFTRocker Block with Bushing WASHER, LOCK, 3/8 MEDPIVOT, Double Rocker ARM, Pivot RightSteering Handles ASSY. RIGHT/LEFT STR46SP Steering Handles ASSY. RIGHT/LEFTHANDLE, Tube GRIP, Handle LTHANDLE, STEERING, Lower SPACER, ROD ENDSteering Assist Control ASSY. RIGHT/LEFT STR46SP Steering Assist Control ASSY. RIGHT/LEFTLEVER, Steering Control Steering Assist AssemblySTR46SP Gearbox ASSY. Right SHAFT, Gearbox Input W/FAN Housing onlyWASHER, FLAT, 1/4 SAE SHROUD, GB FIN COVER, RightSTR46SP Gearbox ASSY. Left Left Hand Worm SHROUD, GB FIN COVER, LeftFAN, Left CCW LEFT-SIDE FAN CoverSingle Pitch Handle ASSY. RIGHT/LEFT STR46SP Single Pitch Handle ASSY. RIGHT/LEFTCrank Knob Cable AssemblySpacer Crank LeverDrive Assy STR46SP Drive AssyBOOT, CV Joint GASKET, CV Joint BootPLATE, Bearing Mount KEY, Woodruff #9ENGINE/MUFFLER/BELT Assy STR46SP ENGINE/MUFFLER/BELT AssyGASKET, Exhaust Manifold NUT, Flange MufflerSTUD, Exhaust SCREW, HEX FlangeAIR CLEANER/OIL FILTER/COOLER Assy STR46SP AIR CLEANER/OIL FILTER/OILCOOLER AssyCOVER, AIR Cleaner KNOB, AIR Cleaner CoverCOVER, Inner AIR Cleaner ELEMENT, PRE-CLEANERBelt COVER/OUTER Muffler Shield Assy STR46SP -V-BELT COVER/OUTER Muffler Shield AssyGUARD, Belt Rear SHIELD, Muffler OuterGUARD, Belt Spider ASSY. Right STR46SP Spider ASSY. RightSCREW, Trowel Adjustment Screw ASSEMBLY, ARM RetainingAccessory Item PLATE, Wear Thrust CollarSpider ASSY, Left STR46SP Spider ASSY. LeftSPRING, Left Trowel ARM Lever Spider ASSY. LeftLEVER, Trowel ARM Left Side ARM, Trowel L.SYoke Assy STR46SP -YOKE AssyPIN, Yoke YokeThrottle CABLE/FOOT Pedals Assy STR46SP -THROTTLE CABLE/FOOT Pedals AssySPRING, Throttle Return CABLE, Control RTROD END, 10 32 Female RH RISER, Left FootControl Panel Assy STR46SP Control Panel AssyBOOT, Toggle Switch SWITCH, Light ToggleIgnition SWITCH, W/KEY HARNESS, Wire EngineFuel Assy STR46SP Fuel AssyFuel CAP/GAUGE TANK, Fuel Five GallonBUSHING, Rubber Fuel VALVE, Screened DapcoBattery Assy STR46SP Battery AssyBracket Battery BOX BOX, Battery GR UIWing NUT, Plated WASHER,LOCK, 1/4 MediumSeat Frame Assy STR46SP Seat Frame AssyCONNECTOR, Relay WIRE, Relay GroundSWITCH, Kill COLE- HER #90036 TERMINAL, WireTerms and Conditions of Sale Stow Construction Equipment STR46SP Notes Your Local Dealer is Heres HOW to GET Help

STR46SP specifications

The Stow STR46SP is a premium storage solution designed for efficiency and functionality, perfect for various applications in both residential and commercial settings. With a focus on durability and ease of use, the STR46SP is an excellent addition to any home or workspace needing effective organization.

One of the standout features of the Stow STR46SP is its robust construction. Made from high-quality materials, this storage unit is designed to withstand the rigors of daily use while maintaining a sleek and modern aesthetic. The frame is constructed from heavy-duty steel, providing stability and strength, while the shelving is crafted from high-density polyethylene that is resistant to impacts, stains, and scratches.

The storage unit boasts a generous capacity, with ample space to accommodate a wide variety of items. With its multiple shelves, the STR46SP allows for efficient categorization and storage, whether you are organizing tools in a garage, files in an office, or supplies in a workshop. Its adjustable shelving system ensures that you can customize the storage dimensions to meet your specific needs, allowing for both tall and short items to be stored without inconvenience.

Another key characteristic of the Stow STR46SP is its mobility. Equipped with heavy-duty wheels, the storage unit can be easily moved from one location to another, allowing for flexible usage in any environment. This feature is particularly beneficial in settings where space is at a premium, enabling users to reposition the unit as required.

The Stow STR46SP also integrates smart design technologies, such as a lockable door mechanism. This provides added security for stored items, ensuring that valuable tools and documents are protected. The unit's ventilation design prevents moisture build-up, prolonging the life of stored materials and keeping everything fresh.

In conclusion, the Stow STR46SP is a versatile and durable storage solution ideal for anyone looking to maximize their space efficiency. With its high-quality construction, ample storage capacity, adjustable shelving, and mobility features, this unit is designed to cater to a wide range of storage needs. Whether in a home garage, office, or workshop, the STR46SP proves to be a reliable and practical investment for effective organization and convenience.
Top Page Image Contents