Stow manual Stow G-2.9R Maintenance Engine, Cleaning the Fuel Strainer

Page 29

STOW G-2.9R — MAINTENANCE (ENGINE)

Maintenance

Perform the scheduled maintenance procedures as defined by Table 6 and below:

DAILY

■Thoroughly remove dirt and oil from the engine and control area.Clean or replace the air cleaner elements as necessary. Check and retighten all fasteners as necessary. Check the gearbox for oil leaks. Repair or replace as needed.

WEEKLY

■Remove the fuel filter cap and clean the inside of the fuel tank.

■Remove or clean the filter at the bottom of the tank.

■Remove and clean the spark plug (Figure 22), then adjust the spark gap to 0.024 ~0.028 inch (0.6~0.7 mm).This unit has electronic ignition, which requires no adjustments.

Cleaning the Fuel Strainer

Clean the fuel strainer if it contains dust or water. Remove dust or water in the strainer cap and wash it in gasoline. Securely fasten the fuel strainer cap so that fuel will not leak. Check the fuel strainer every 200 hours of operation or once a month.

DANGER

DO NOT use gasoline as a cleaning solvent, because that would create a risk of fire or explosion.

ENGINEAIRCLEANER

1.Remove the air cleaner cover and foam filter element as shown in Figure 24.

2.Tap the paper filter element (Figure 24) several times on a hard surface to remove dirt, or blow compressed air [not exceeding 30 psi (207 kPa, 2.1 kgf/cm2)] through the filter elementfromtheaircleanercaseside.NEVER brushoffdirt. Brushingwillforcedirtintothefibers.Replacethepaperfilter element if it is excessively dirty.

Figure 22. Spark Plug Gap

ENGINE OIL

1.Drain the engine oil when the oil is warm as shown in Figure 21.

2.Remove the oil drain bolt and sealing washer and allow the oil to drain into a suitable container.

3.Replace engine oil with recommended type oil as listed in Table 4. For engine oil capacity, see Table 2 (engine specifications). DO NOT overfill.

4.Install drain bolt with sealing washer and tighten se- curely.

Figure 24. Engine Air Cleaner

Figure 23. Engine Oil (Draining)

STOW G-2.9R A.C. GENERATOR — OPERATION & PARTS MANUAL — REV. #1 (10/28/04) — PAGE 29

Page 28 Page 30
Image 29
Page 28 Page 30
Contents Model G-2.9R Page Heres HOW to GET Help Table of Contents When ordering parts Please supply the following information Parts Ordering ProceduresDimensions Stow G-2.9R DimensionsEffects of Altitude and Heat SpecificationsRespiratory Hazards Stow G-2.9R Safety Message Alert SymbolsBurn Hazards Rotating Parts Hazards Equipment DamageRead this manual Stow G-2.9R Rules for Safe OperationStow G-2.9R Rules for Safe Operation Emergencies Stow G-2.9R Rules for Safe OperationPage Machine Safety Decals Operation and Safety Decals S/N 5497956 and belowOperation and Safety Decals S/N 5497957 and Above Stow G-2.9R Familarization Stow G-2.9R General InformationControl Panel Excitation SystemExtension Cables Single Phase LoadStow G-2.9R Load Application Generator Controls and Components Stow G-2.9R Controls and IndicatorsStow G-2.9R Controls and Indicators Generator Refueling Stow G-2.9R Generator RefuelingOutdoor Installation Stow G-2.9R InstallationIndoor Installation MountingConnecting the Ground Stow G-2.9R InstallationStow G-2.9R PRE-INSPECTION General Inspection Prior to Operation Ground Power ToolsExtension Cable Main Circuit BreakerBefore Starting Stow G-2.9R PRE-INSPECTION EngineEngine Oil Check Fuel CheckBefore Starting the Engine Stow G-2.9R Initial START-UP EngineStopping The Engine Connecting the LoadStow G-2.9R Initial START-UP ENGINE/OPERATION Generator Storage Stow G-2.9R Preparation for Long -TERM StorageEngine Maintenance Schedule Stow G-2.9R Maintenance EngineMaintenance Stow G-2.9R Maintenance EngineCleaning the Fuel Strainer Generator/Engine Wiring Diagram S/N 5497956 and Below Stow G-2.9R Wiring Diagram S/N 5497956 and belowStow G-2.9R Wiring Diagram S/N 5497957 and Above Engine Troubleshooting Stow G-2.9R -TROUBLESHOOTING EngineStow G-2.9R -TROUBLESHOOTING Engine Generator Troubleshooting Stow G-2.9R -TROUBLESHOOTING GeneratorPage Items Found In the Items Number Column How to read the marks and remarks used in this parts bookStow G-2.9R Explanation of Code in Remarks Column To 3 Units Stow G-2.9R Suggested Spare PartsStow G-2.9R Name Plate and Decals S/N 5497956 and below Stow G-2.9R Name Plate and Decals S/N 5497956 and below Stow G-2.9R Name Plate and Decals S/N 5497957 and Above Part Name QTY Remarks Stow G-2.9R Generator Assy SET BOLT, Rotor Stow G-2.9R Control BOX ASSY. S/N 5497956 and below Stow G-2.9R Control BOX ASSY. S/N 5497956 and below Stow G-2.9R Control BOX ASSY. S/N 5497957 and Above Stow G-2.9R Control BOX ASSY. S/N 5497957 and Above Stow G-2.9R Pipe Frame ASSY. S/N 5497956 and below Fuel GAUGE, CJ- 58A Stow G-2.9R Pipe Frame ASSY. S/N 5497956 and belowStow G-2.9R Pipe Frame ASSY. S/N 5497956 and Above A2417000302 Robin EX170D20210 Crankcase Assy Robin EX170D20210- Crankcase Assy Robin EX170D20210 Crankshaft and Piston Assy Crankshaft Assy Robin EX170D20210 Governor Assy Part Name QTY. Remarks Robin EX170D20210 Intake and Exhaust Assy PIN, CAM Shaft Robin EX170D20210 AIR Cleaner Assy Robin EX170D20210 AIR Cleaner Assy Robin EX170D20210 Cooling Starting Assy Blower Housing CP, Yellow Robin EX170D20210 -CARBURETOR Assy Robin EX170D20210 Carburetor Assy Robin EX170D20210 Flywheel Assy Part Name QTY Robin EX170D20210 Electric Device Assy OIL Sensor CP Terms and Conditions of Sale Parts Terms and Conditions of Sale Stow Construction EquipmentPage Your Local Dealer is

G-2.9R specifications

The Stow G-2.9R is an innovative and highly versatile piece of equipment designed for a variety of applications, making it a valuable asset in various industries. This unit stands out for its unique combination of power, efficiency, and user-friendly features, ensuring that it meets the demands of both professionals and casual users alike.

One of the main features of the Stow G-2.9R is its robust engine, which is designed to deliver reliable performance. With a powerful output, the engine allows users to tackle demanding tasks with ease, whether it’s in landscaping, construction, or maintenance jobs. The efficient fuel consumption of the G-2.9R not only reduces operational costs but also minimizes environmental impact, making it an eco-friendly choice for users conscious of their carbon footprint.

The Stow G-2.9R is equipped with advanced technologies that enhance its performance and usability. The integrated electronic controls provide precise management of operations, allowing users to finely tune the machine's settings according to specific requirements. This level of precision is particularly beneficial in applications such as turf management or industrial cleaning, where different surfaces and conditions may require specific adjustments.

Another noteworthy characteristic of the Stow G-2.9R is its compact design. Built for maneuverability, this machine can easily navigate tight spaces without sacrificing power or efficiency. The lightweight construction allows for easy transportation, making it suitable for different job sites. Its geometrically designed chassis ensures stability and balance during operation, enhancing safety for the user.

Furthermore, the G-2.9R also boasts ergonomic controls and comfortable handling features. The adjustable components allow users to customize their experience, which contributes to reduced fatigue during extended use. Safety features are also a priority, with mechanisms in place to protect the operator and nearby workers from potential hazards.

Durability is another key aspect of the Stow G-2.9R, as it is built with high-quality materials that withstand wear and tear in challenging working environments. The machine is designed for longevity, making it a cost-effective investment for users.

In summary, the Stow G-2.9R combines power, efficiency, advanced technology, and user-centered design to deliver exceptional performance across a wide range of applications. Its adaptable nature ensures that it meets the varying needs of users, positioning it as a reliable choice in the marketplace.
Top Page Image Contents