Shindaiwa 81719, LE2510 manual Safety Instructions, Properly Equipped Operator

Page 3

Safety Instructions

Work Safely

Shindaiwa Edgers operate at very high speeds and can do serious damage or injury if they are misused or abused. Never allow a person without training or instruction to operate this unit!

WARNING!

Never make unauthorized attach- ment installations. Do not use attachments not approved by Shindaiwa for use on this unit.

Stay Alert

You must be physically and mentally fit to operate this unit safely.

WARNING!

Never operate

 

power equipment of any

 

kind if you are tired or if you

 

are under the influence of alcohol, drugs, medication or any other substance that could affect your ability or judgement.

WARNING!

The engine exhaust from this product contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm.

WARNING!

Minimize the Risk of Fire

NEVER smoke or light fires near the engine.

ALWAYS stop the engine and allow it to cool before refueling. Avoid overfilling and wipe off any fuel that may have spilled.

ALWAYS inspect the unit for fuel leaks before each use. During each refill, check that no fuel leaks from around the fuel cap and/or fuel tank. If fuel leaks are evident, stop using the unit immediately. Fuel leaks must be repaired before using the unit.

ALWAYS move the unit to a place well away from a fuel storage area or other readily flammable materials before starting the engine.

NEVER place flammable material close to the engine muffler.

NEVER operate the engine without the spark arrester screen in place.

 

WARNING!

 

 

Use Good Judgment

 

ALWAYS wear eye protection to shield

ALWAYS use the proper cutting

ALWAYS hold the unit firmly with both

against thrown objects.

attachment.

hands when edging, and maintain control

NEVER run the engine when transporting

ALWAYS stop the engine immediately

at all times.

the unit.

if it suddenly begins to vibrate or shake.

ALWAYS keep the handles clean.

NEVER run the engine indoors! Make sure

Inspect for broken, missing or improperly

ALWAYS disconnect the spark plug wire

there is always good ventilation. Fumes

installed parts or attachments.

before performing any maintenance work.

NEVER use a non-Shindaiwa approved

from engine exhaust can cause serious

 

injury or death.

cutting attachment.

 

ALWAYS clear your work area of trash or

ALWAYS keep the unit as clean as

 

hidden debris that could be thrown back at

practical. Keep it free of loose vegetation,

 

you or toward a bystander.

mud, etc.

 

 

 

 

The Properly Equipped Operator

Wear close-fitting clothing to protect legs and arms. Gloves offer added protection and are strongly recom- mended. Do not wear clothing or jewelry that could get caught in machinery or underbrush. Secure hair so it is above shoulder level. NEVER wear shorts!

Keep a proper footing and do not overreach—main- tain your balance at all times during operation.

Wear appropriate footwear (non-skid boots or shoes): do not wear open-toed shoes or sandals. Never operate the unit while barefoot!

Wear hearing protection devices and a

broad-brimmed hat or helmet.

Always wear eye protection such as goggles or safety glasses.

Always operate with both hands firmly gripping the unit.

Always make sure the appropriate cutting attachment shield is correctly installed and in good condition.

Keep away from the rotating blade at all times, and never lift a moving attachment above waist-high.

Figure 1



Image 3
Contents LE2510 Lawn Edger Introduction ContentsProperly Equipped Operator Safety InstructionsBe Aware of the Working Environment Safety LabelsSpecifications Prior to AssemblyProduct Description Adjust Throttle Lever Free Play Assembly and AdjustmentsMixing Fuel Filling the Fuel TankExamples of 501 mixing quantities Starting the Engine When the Engine StartsChecking Unit Condition Adjusting Engine IdleIdle Speed Adjustment Stopping the EngineGuidelines for Operating the Edger Using a Hand-held EdgerAdjusting the Blade To adjust blade heightGeneral Maintenance Daily MaintenanceHour Maintenance Every 10 to 15 hours of operation 10/15-Hour MaintenanceEvery 50 hours of operation more fre Quently in dusty or dirty conditions139/150-Hour Maintenance Valve AdjustmentInspect the Gearcase Protector Exhaust Port Inspection Spark Arrester Screen MaintenanceReplacing the Edger Blade Long Term StorageEngine does not Start Troubleshooting GuideAdditional Problems Manufacturers Warranty Coverage Telephone 503 731-3167, Japan Fax 81-82-849-2481 8492 Corporation Shindaiwa Com.shindaiwa.www 50 69366962 -FaxOregon Tualatin Rd Herman .W.S Inc Shindaiwa Garantía DE Servicio DE Solicitudes Adicionales Problemas Continuación Diagnostico GuiaPotencia Baja Diagnostico GuiaCilindro del Escape de Inspección Plazo Largo de AlmacenamientoOrilladora la de Cuchilla la Reemplazar Guardachispas Maya la de MantenimientoHoras 139/150 Cada Mantenimiento Continuación Horas 50 Cada MantenimientoEngranajes de Caja la de Protector el Inspeccione Horas 10/15 Cada Mantenimiento Horas 50 Cada MantenimientoHoras-10 Cada Mantenimiento Diario MantenimientoGeneral Mantenimiento Cuchilla La De Ajuste El Mano de Orillador el UtilizandoRecauciónP Unidad la de Condición la Verifique Motor del Mínima Marcha de AjusteMotor del Parada Rápidam jale luego resistencia, sienta Motor del Arranque…motor el arranca Cuando Motor el arrancar para enteCombustible de Tanque el Llenando Combustible de MezclaDe proporción Acelerador del Holgura la Ajuste Ajustes y EnsamblajeSeguridad de tuercas las Apriete Pulgadas 1/4-/163Ensamblar de Antes EspecificacionesTrabajo de Area del Alerta Esté Seguridad de EtiquetasCuidado con Trabaje Equipado Debidamente Operario ElSeguridad de Generales Instrucciones Alerta MantengaseSeguridad de Declaraciones Introducción ContenidoRev 81719 pieza de Número