Shindaiwa LE2510, 81719 manual 10/15-Hour Maintenance, Every 50 hours of operation more fre

Page 12

10/15-Hour Maintenance

Clean the spark plug and check the gap at

0.024–0.028 inchthe electrode. (0.6–0.7 mm)

Figure 19

50-Hour Maintenance

Every 50 hours of operation (more fre-

Use a hooked wire to extract the fuel filter

quently in dusty or dirty conditions):

from inside the fuel tank. See Figure 22.

n Remove the cylinder cover and clean

Remove and replace the filter element.

Before reinstalling the new filter ele-

grass and dirt from the cover and

ment, inspect the condition of all the

cylinder fins.

fuel system components (fuel pick-up

n Remove the cutting attachment, cutting

line, fuel return line, tank vent line, tank

attachment holder and gear shaft collar.

vent, fuel cap and fuel tank). If damage,

Remove the filler plug from the side

splitting or deterioration is noted, the

of the gearcase and press new grease

unit should be removed from service

into the gearcase until grease is pushed

until it can be inspected or repaired by a

out. Use only lithium-base grease such

Shindaiwa-trained service technician.

as Shindaiwa Gear Case Lubricant or

 

equivalent. See Figure 20.

 

 

Old

 

 

New

 

 

Grease

Grease

 

 

 

 

 

 

 

 

Hooked

 

 

 

Wire

 

 

Blade

Output

 

 

Shaft Collar

 

 

 

Filter Element

Shaft

Bolt

Holder

Holder

Bolt

Guard

A

B

Figure 20

 

Figure21

Every 10 to 15 hours of operation:

nRemove and clean the spark plug. Adjust the spark plug electrode gap to 0.024 0.028 inch (0.6-0.7 mm). If the spark plug must be replaced, use only an NGK CMR5H or equivalent resistor type spark plug of the correct heat range. See Figure 19.

NOTE:

The NGK CMR5H also meets the require- ments for electro magnetic compliance (EMC).

CAUTION!

Before removing the spark plug, clean the area around the plug to prevent dirt and debris from getting into the engine’s internal parts.

Gearcase Index

Screw

Flexible Shaft

Shaft Tube

Figure 22

3.Slide the gearcase and shield assembly from the shaft tube.

4.Pull the flexible shaft from the shaft tube assembly, and clean the shaft thoroughly in solvent.

5.Inspect the shaft carefully, and replace if worn or damaged. If flexible shaft is worn and needs replacement, liner should also be replaced.

6.Coat the entire length of the shaft with Shindaiwa Premium Gearcase Lube (or equivalent), and reinstall the shaft in the shaft tube assembly.

NOTE:

For extended shaft life, the flexible cable should be reversed end-for-end during the

CAUTION!

Make sure you do not pierce the fuel line with the end of the hooked wire. The line is delicate and can be dam- aged easily.

Lubricate the Flexible Shaft.

Lack of lubrication will cause rapid wear to the flexible shaft and also to the shaft tube liner, resulting in increased vibration and greatly decreased service life. Remove and lubricate the flexible shaft as follows:

1.Loosen the gearcase clamp screw.

2.Remove the gearcase index screw.

reinstallation process.

7.Insert the flexible shaft into the female end of the gearcase pinion.

8.Install the gearcase on the shaft tube in the reverse order of removal.

12

Image 12
Contents LE2510 Lawn Edger Contents IntroductionSafety Instructions Properly Equipped OperatorSafety Labels Be Aware of the Working EnvironmentSpecifications Prior to AssemblyProduct Description Assembly and Adjustments Adjust Throttle Lever Free PlayMixing Fuel Filling the Fuel TankExamples of 501 mixing quantities When the Engine Starts Starting the EngineAdjusting Engine Idle Idle Speed AdjustmentStopping the Engine Checking Unit ConditionUsing a Hand-held Edger Adjusting the BladeTo adjust blade height Guidelines for Operating the EdgerGeneral Maintenance Daily MaintenanceHour Maintenance 10/15-Hour Maintenance Every 50 hours of operation more freQuently in dusty or dirty conditions Every 10 to 15 hours of operation139/150-Hour Maintenance Valve AdjustmentInspect the Gearcase Protector Spark Arrester Screen Maintenance Replacing the Edger BladeLong Term Storage Exhaust Port InspectionTroubleshooting Guide Engine does not StartAdditional Problems Manufacturers Warranty Coverage Telephone 503 731-3167, Japan Fax 81-82-849-2481 8492 Corporation Shindaiwa Com.shindaiwa.www 50 69366962 -FaxOregon Tualatin Rd Herman .W.S Inc Shindaiwa Garantía DE Servicio DE Solicitudes Continuación Diagnostico Guia Adicionales ProblemasDiagnostico Guia Potencia BajaPlazo Largo de Almacenamiento Orilladora la de Cuchilla la ReemplazarGuardachispas Maya la de Mantenimiento Cilindro del Escape de InspecciónHoras 139/150 Cada Mantenimiento Continuación Horas 50 Cada MantenimientoEngranajes de Caja la de Protector el Inspeccione Horas 50 Cada Mantenimiento Horas 10/15 Cada MantenimientoHoras-10 Cada Mantenimiento Diario MantenimientoGeneral Mantenimiento Cuchilla La De Ajuste El Mano de Orillador el UtilizandoRecauciónP Unidad la de Condición la Verifique Motor del Mínima Marcha de AjusteMotor del Parada Motor del Arranque …motor el arranca CuandoMotor el arrancar para ente Rápidam jale luego resistencia, sientaCombustible de Tanque el Llenando Combustible de MezclaDe proporción Ajustes y Ensamblaje Seguridad de tuercas las AprietePulgadas 1/4-/163 Acelerador del Holgura la AjusteEspecificaciones Ensamblar de AntesSeguridad de Etiquetas Trabajo de Area del Alerta EstéEquipado Debidamente Operario El Seguridad de Generales InstruccionesAlerta Mantengase Cuidado con TrabajeContenido Seguridad de Declaraciones IntroducciónRev 81719 pieza de Número