WASHER
MAINTENANCE
PREVENTATIVE MAINTENANCE |
| compressed air is available, an air fitting can be | ||
screwed into the float tank by removing the float tank | ||||
1. | Check to see that water pump is properly lubricated. | strainer and fitting. Then inject the compressed air. | ||
Water will be blown out of the machine when the trig- | ||||
2. | Follow winterizing instructions to prevent freeze | |||
ger on the spray gun is opened. | ||||
| damage to pump and coils. | |||
|
| |||
OPERATOR’S MANUAL PRESSURE
12
3.Always neutralize and flush detergent from sys- tem after use.
4.If water is known to have high mineral content, use a water softener in your water system, or
5.Do not allow acidic, caustic or abrasive fluids to be pumped through system.
6.Always use high grade quality cleaning products.
7.Never run pump dry for extended periods of time.
8.Use clean fuel: kerosene, No. 1 fuel oil, or diesel. Clean or replace fuel filter every 100 hours of op- eration. Avoid water contaminated fuel as it will damage the fuel pump.
9.If machine is operated with smoky or eye burning exhaust, coils will soot up, not letting water reach maximum operating temperature.
10.Never allow water to be sprayed on or near engine or burner assembly or any electrical component.
11.Periodically delime coils as per instructions.
12.Check to see that engine is properly lubricated.
It is advisable, periodically, to visually inspect the burner. Check air inlet to make sure it is not clogged or blocked. Wipe off any oil spills and keep equipment clean and dry.
The flow of combustion and ventilating air to the burner must not be blocked or obstructed in any manner.
The area around the pressure washer should be kept clean and free of combustible materials, gasoline and other flammable vapors and liquids.
MAINTENANCE AND SERVICE
Unloader Valves:
Unloader valves are preset and tested at the factory before shipping. Occasional adjustment of the unloader may be necessary to maintain correct pressure.
Winterizing Procedure:
Damage due to freezing is not covered by warranty. Adhere to the following cold weather procedures when- ever the washer must be stored or operated outdoors under freezing conditions.
During winter months, when temperatures drop below 32°F, protecting your machine against freezing is nec- essary. Store the machine in a heated room. If this is not possible then mix a 50/50 solution of
High Limit Hot Water Thermostat:
For safety, each machine is equipped with a tempera- ture sensitive high limit control switch. In the event that the water should exceed its operating temperature, the high limit control will turn the burner off until the water cools then it will automatically reset itself. The thermostat sensor is located on the discharge side of the heating coil. The thermostat control dial is located on the control panel.
Pumps:
Before running the pump check the pump crankcase for a proper oil level. A proper oil level is indicated by the red dot in the sightglass or between the high and low marks on the dipstick. Use only SAE 30
When draining oil, clean inside of crankcase to remove all impurities. CAUTION: When operating in damp places or with high temperature fluctuations oil must be changed immediately.
Cleaning of Coils:
In alkaline water areas, lime deposits can accumulate rapidly inside the heating coil.This growth is increased by the extreme heat build up in the coil. The best pre- ventative for liming conditions is to use high quality cleaning detergents. In areas where alkaline water is an extreme problem, periodic use of Coil Conditioner will remove lime and other deposits before coil be- comes plugged. (See Deliming instructions for use of Coil Conditioner.)
Deliming Coils:
Periodic flushing of coils or optional float tank is rec- ommended.
Step 1 Fill a container with 4 gallons of water, then add 1 lb. of deliming powder. Mix thoroughly. Pour mixture into float tank.
Step 2 Remove wand assembly from spray gun and put spray gun into float tank. Secure the trig- ger on the spray gun into the open position.
Step 3 Turn engine on, allowing solution to be pumped through coils back into the float tank. The solution should be allowed to circulate 2- 4 hours or until the color changes.
Step 4 After circulating solution, flush the entire sys- tem with fresh water. Clean out float tank and then reinstall wand assembly to spray gun.
SHARK SSG •