McIntosh C500 owner manual Trigger Selection, Accessory Control

Page 22

10.If no other adjustments are to be made at this time, press the SETUP Push-button to exit the Setup Preamp Mode or proceed to the next desired Setup Preamp Mode for adjustment.

Trigger Selection

The Trigger A and B Power Control Outputs on the C500 Controller are reassignable from their default settings to ac- tivate only when a given Input(s) is selected. To change ei- ther Trigger A or B from the default setting perform the fol- lowing steps:

Note: Power Control Cables coming from the components to be controlled need to be connected to the correct Trigger Jack on the Rear Panel of the C500C to function.

1.Press the SETUP Push-button twice to access the Setup Preamp Mode unless the C500C is already in the Setup Preamp Mode.

2.Rotate the MENU Control until the Alphanumeric Dis- play indicates “TRIG TUN --” . Refer to figure 36.

Figure 36

3.Rotate the SELECT 1 Control until the desired Input Title to be changed appears in the Display, e.g. “TRIG DVD --” .

4.Rotate the SELECT 2 Control until the desired Trigger A or B (in this example the DVD Input will activate the Trigger A Jack) appears in the Display, e.g. “TRIG DVD A”. Refer to figure 37.

Accessory Control

When the Trigger A or B Power Control Outputs on the C500 Controller are used, one of the Triggers may be as- signed to switched On or Off by using the ACCessory Push- button on the supplied Remote Control. To select either Trigger A or B for remote operation, perform the following steps:

1.Press the SETUP Push-button twice to access the Setup Preamp Mode unless the C500C is already in the Setup Preamp Mode.

2.Rotate the MENU Control until the Alphanumeric Dis- play indicates “ACC CONTROL --”. Refer to figure 38.

Figure 38

3.Rotate the SELECT 2 Control until the desired Trigger A or B appears in the Display, e.g. “ACC CONTROL A”. Refer to figure 39.

Figure 39

Note: Devices connected to the Trigger (A or B) Jacks will be effected when Trigger (A or B) in SETUP is changed.

4.If no other adjustments are to be made at this time, press the SETUP Push-button to exit the Setup Preamp Mode or proceed to the next desired Setup Preamp Mode for adjustment.

Figure 37

Note: Additional Inputs may also be assigned in the same manner to also activate Trigger A.

5.If no other adjustments are to be made at this time, press the SETUP Push-button to exit the Setup Preamp Mode or proceed to the next desired Setup Preamp Mode for adjustment.

22

Page 21 Page 23
Image 22
Page 21 Page 23
Contents Controller/Preamplifier/Tube Preamplifier Important Safety Instructions Thank You Customer ServiceTable of Contents Please Take a MomentImportant Information Connector InformationIntroduction Introduction and Performance Features Dimensions Side View of the C500C17-1/2 Dimensions, con’t Installation Page C500 Preamplifier Rear Panel Connections C500 ControllerC500 Tube Preamplifier Data Control Connections How to connect the C500Power Control Connections Audio ConnectionsPower Connections Passthru ConnectionsPage Page How to Operate the Setup Modes Remote Control SetupDefault Settings Firmware VersionVolume Display Trigger a Voltage Power ControlMeter Illumination Triamp Balanced Outputs Setup, con’t Trigger B Voltage Power ControlControl McIntosh MDA1000 Input Selection and Title Reassignment Data Port AssigmentSetup, con’t Trim Level AdjustmentAccessory Control Trigger SelectionListen Processor Record ProcessorMoving Magnet Cartridge Capacitance Passthru ModeMoving Coil Cartridge Resistance Setup, con’t and Setup Settings Charts C500 Preamplifier or C500 Tube PreamplifierRemote Control Push-Buttons Mono VolumeMute TrimPower On How to Operate the C500Source Selection How To Make a Recording Volume ControlSetup Mode Listen and Record External ProcessorsOutput Meters Mono ModeSpeaker Output 1 How to Operate the C500, con’t How to use the Passthru ModeReset of Microprocessors Configuration ChangeSilent Audio Switching How to Operate the C500, con’t and Technical DescriptionVolume Adjustments Fully Balanced Circuitry Logic Controlled Circuitry Technical Description, con’tMoving Coil Preamplifier Meter and CircuitryPower Supply Circuits Block DiagramsSpecifications C500 Preamplifier and C500 Tube Preamplifier Specifications C500 Tube PreamplifierPower Requirements Specifications C500 Controller and GeneralGeneral Specifications Overall DimensionsPacking Instructions McIntosh Laboratory, Inc Chambers Street Binghamton, NY
Top Page Image Contents