McIntosh C500 owner manual Remote Control Push-Buttons

Page 26

Remote Control Push-Buttons

LED illuminates during the time a remote com- mand is sent to the C500

Turns AC Power ON or OFF to certain McIntosh Components when connected via the Data Port

Selects Functions for McIntosh Home Controller and as a “shift” key when used with the AM or FM push-buttons to select Output 1 or 2

Switches OFF the entire C500 System except in Passthru Mode

Use to select tuner pre- sets, disc tracks or any numbered operation

Selects Switched Output 1, AM Tuner Operating Func- tions and Disc Selection on certain McIntosh CD Players

Press TRIM and then the LEVEL Push-but- tons to select and ad- just various functions

Mutes the audio

Selects Disc Player, Mu- sic Server or Tape Re- corder Functions and also performs various func- tions on a variety of McIntosh Components

Selects one of the seven

High Level Audio/Video

Sources or Phono Input

Press to listen to the se- lected Record out signal

Press to Power the C500 ON or OFF

Press MODE to switch the

MONO Mode On or Off

Press to Power ON the C500

Press to Power OFF the C500

Selects Switched Output 2, FM Tuner Operating Functions and Track Se- lection on certain McIn- tosh CD Players

Press +10 to Review Tuner Station Presets and select certain functions on McIn- tosh CD Players

Adjusts the volume level up or down

Selects On Screen Func- tions for McIntosh DVD Players and certain CD Players

Selects the FF (Fast For- ward) or REWind Mode on a Disc Player, Music Server or Tape Recorder; tunes Up or Down the AM/FM Dial

Scrolls through the available C500 Inputs and the McIntosh MDA1000 Digital Sources when connected to the D/A Input1

Note: Push-buttons whose function is not indentified above are for use with other McIntosh Products.

1Requires a Data Cable Connection between the C500C and the MDA1000

26

Page 25 Page 27
Image 26
Page 25 Page 27
Contents Controller/Preamplifier/Tube Preamplifier Important Safety Instructions Thank You Customer ServiceTable of Contents Please Take a MomentIntroduction Connector InformationImportant Information Introduction and Performance Features Dimensions Side View of the C500C17-1/2 Dimensions, con’t Installation Page C500 Tube Preamplifier Rear Panel Connections C500 ControllerC500 Preamplifier Data Control Connections How to connect the C500Power Control Connections Audio ConnectionsPower Connections Passthru ConnectionsPage Page How to Operate the Setup Modes Remote Control SetupDefault Settings Firmware VersionMeter Illumination Trigger a Voltage Power ControlVolume Display Control McIntosh MDA1000 Setup, con’t Trigger B Voltage Power ControlTriamp Balanced Outputs Input Selection and Title Reassignment Data Port AssigmentSetup, con’t Trim Level AdjustmentAccessory Control Trigger SelectionListen Processor Record ProcessorMoving Coil Cartridge Resistance Passthru ModeMoving Magnet Cartridge Capacitance Setup, con’t and Setup Settings Charts C500 Preamplifier or C500 Tube PreamplifierRemote Control Push-Buttons Mono VolumeMute TrimSource Selection How to Operate the C500Power On How To Make a Recording Volume ControlSetup Mode Listen and Record External ProcessorsSpeaker Output 1 Mono ModeOutput Meters How to Operate the C500, con’t How to use the Passthru ModeReset of Microprocessors Configuration ChangeVolume Adjustments How to Operate the C500, con’t and Technical DescriptionSilent Audio Switching Fully Balanced Circuitry Logic Controlled Circuitry Technical Description, con’tMoving Coil Preamplifier Meter and CircuitryPower Supply Circuits Block DiagramsSpecifications C500 Preamplifier and C500 Tube Preamplifier Specifications C500 Tube PreamplifierPower Requirements Specifications C500 Controller and GeneralGeneral Specifications Overall DimensionsPacking Instructions McIntosh Laboratory, Inc Chambers Street Binghamton, NY
Top Page Image Contents