McIntosh C500 owner manual Reset of Microprocessors, Configuration Change

Page 32
Figure 86

Reset of Microprocessors

In the event that the controls of the C500 stop functioning press and hold the STANDBY/ON Push-button. Three to four seconds later the Front Panel Alphanumeric Display will indicate “DETECT SYSTEM”; at this point release the STANDBY/ON Push-button. This will reset the C500 microprocessors. Refer to figure 85.

Figure 85

Note: The above condition is usually caused by either interruptions in AC power and/or major changes in voltage.

Configuration Change

When a change is made to a C500 System (Controller and Preamplifier) by changing the current Preamplifier type (C500P or C500T) , the Front Panel Alphanumeric Display will indicate “CONFIG CHANGE” and the LED indicators above the SETUP and REC MONITOR Push-buttons will be flashing. Refer to figures 86

and 87. If there is not to be any

changes to the C500 System, but rather reconnecting a

Preamplifier that was previ- ously connected to the C500 Controller perform the follow- ing:

Figure 87

1.Remove the AC Power Cord from the Rear Panel of the C500 Controller.

2.Reconnect the previously connected Preamplifier.

3.Reattach the AC Power Cord.

4.The C500 System will automatically reset itself and will retain any changes that where previously made in the SETUP Mode.

If the change to the C500 System is a result of changing Preamplifier Types (C500P or C500T) then perform the fol- lowing steps:

1.Remove the AC Power Cord from the Rear Panel of C500 Controller.

2.Connected the Preamplifier(s) to the C500 Controller.

3.Reteach the AC Power Cord.

4.Press and hold the SETUP and REC MONITOR Front Panel Push-buttons until the Alphanumeric Display in- dicates “DETECT SYSTEM”, then release the two Push-buttons. At this point several messages will ap- pear on the Alphanumeric Display depending on the C500 System makeup. Refer to figures 88 thru 91.

Figure 88

Figure 89

Figure 90

Figure 91

5.For any changes from the default settings that are de- sired go to page 16 SETUP to perform them at this time.

32

Image 32
Contents Controller/Preamplifier/Tube Preamplifier Important Safety Instructions Customer Service Table of ContentsThank You Please Take a MomentIntroduction Connector InformationImportant Information Introduction and Performance Features Dimensions Side View of the C500C17-1/2 Dimensions, con’t Installation Page C500 Tube Preamplifier Rear Panel Connections C500 ControllerC500 Preamplifier How to connect the C500 Power Control ConnectionsData Control Connections Audio ConnectionsPower Connections Passthru ConnectionsPage Page How to Operate the Setup Modes Setup Default SettingsRemote Control Firmware VersionMeter Illumination Trigger a Voltage Power ControlVolume Display Control McIntosh MDA1000 Setup, con’t Trigger B Voltage Power ControlTriamp Balanced Outputs Input Selection and Title Reassignment Data Port AssigmentSetup, con’t Trim Level AdjustmentAccessory Control Trigger SelectionListen Processor Record ProcessorMoving Coil Cartridge Resistance Passthru ModeMoving Magnet Cartridge Capacitance Setup, con’t and Setup Settings Charts C500 Preamplifier or C500 Tube PreamplifierRemote Control Push-Buttons Volume MuteMono TrimSource Selection How to Operate the C500Power On Volume Control Setup ModeHow To Make a Recording Listen and Record External ProcessorsSpeaker Output 1 Mono ModeOutput Meters How to Operate the C500, con’t How to use the Passthru ModeReset of Microprocessors Configuration ChangeVolume Adjustments How to Operate the C500, con’t and Technical DescriptionSilent Audio Switching Fully Balanced Circuitry Technical Description, con’t Moving Coil PreamplifierLogic Controlled Circuitry Meter and CircuitryPower Supply Circuits Block DiagramsSpecifications C500 Preamplifier and C500 Tube Preamplifier Specifications C500 Tube PreamplifierSpecifications C500 Controller and General General SpecificationsPower Requirements Overall DimensionsPacking Instructions McIntosh Laboratory, Inc Chambers Street Binghamton, NY