McIntosh Specifications C500 Controller and General, General Specifications, Weight

Page 38

Specifications C500 Controller and General

Specifications C500 Controller

Power Requirements

100 Volts, 50/60Hz at 75 watts

110 Volts, 50/60Hz at 75 watts

120 Volts, 50/60Hz at 75 watts

220 Volts, 50/60Hz at 75 watts

230 Volts, 50/60Hz at 75 watts

240 Volts, 50/60Hz at 75 watts

Note: Refer to the rear panel of the C500 Controller for the correct voltage.

General Specifications

Overall Dimensions

C500C:

Width is 17-1/2 inches (44.45cm)

Height is 6 inches (15.24cm) including feet

Depth is 24 inches (61.00cm) including the Front Panel, Knobs and Interconnect Cables1

C500P:

Width is 17-1/2 inches (44.45cm)

Height is 6 inches (15.24cm) including feet

Depth is 23 inches (58.42cm) including the Front Panel and Interconnect Cables1

C500T:

Width is 17-1/2 inches (44.45cm)

Height is 6 inches (15.24cm) including feet

Depth is 23 inches (58.42cm) including the Front Panel and Interconnect Cables1

Weight

C500C - 30.1 pounds (17.7 kg) net

46.5pounds (27.9 kg) in shipping carton C500P - 25.1 pounds (15.0 kg) net

41.5pounds (24.3 kg) in shipping carton C500T - 26.4 pounds (15.4 kg) net

42.8pounds (24.8 kg) in shipping carton

1The Custom Interconnect Cables are supplied with the C500 Preamplifier and C500 Tube Preamplifier. They are the ONLY cables to be used for connecting a C500 Controller to the C500 Preamplifier or C500 Tube Preamplifier.

38

Image 38
Contents Controller/Preamplifier/Tube Preamplifier Important Safety Instructions Thank You Customer ServiceTable of Contents Please Take a MomentIntroduction Connector InformationImportant Information Introduction and Performance Features Dimensions Side View of the C500C17-1/2 Dimensions, con’t Installation Page C500 Tube Preamplifier Rear Panel Connections C500 ControllerC500 Preamplifier Data Control Connections How to connect the C500Power Control Connections Audio ConnectionsPower Connections Passthru ConnectionsPage Page How to Operate the Setup Modes Remote Control SetupDefault Settings Firmware VersionMeter Illumination Trigger a Voltage Power ControlVolume Display Control McIntosh MDA1000 Setup, con’t Trigger B Voltage Power ControlTriamp Balanced Outputs Input Selection and Title Reassignment Data Port AssigmentSetup, con’t Trim Level AdjustmentAccessory Control Trigger SelectionListen Processor Record ProcessorMoving Coil Cartridge Resistance Passthru ModeMoving Magnet Cartridge Capacitance Setup, con’t and Setup Settings Charts C500 Preamplifier or C500 Tube PreamplifierRemote Control Push-Buttons Mono VolumeMute TrimSource Selection How to Operate the C500Power On How To Make a Recording Volume ControlSetup Mode Listen and Record External ProcessorsSpeaker Output 1 Mono ModeOutput Meters How to Operate the C500, con’t How to use the Passthru ModeReset of Microprocessors Configuration ChangeVolume Adjustments How to Operate the C500, con’t and Technical DescriptionSilent Audio Switching Fully Balanced Circuitry Logic Controlled Circuitry Technical Description, con’tMoving Coil Preamplifier Meter and CircuitryPower Supply Circuits Block DiagramsSpecifications C500 Preamplifier and C500 Tube Preamplifier Specifications C500 Tube PreamplifierPower Requirements Specifications C500 Controller and GeneralGeneral Specifications Overall DimensionsPacking Instructions McIntosh Laboratory, Inc Chambers Street Binghamton, NY