Neuton CE 6.2 manual Sharpening the Blade

Page 42

1.Remove the Safety Key and the Battery. If you are charging the Battery in the Mower, first disconnect the Charger from the electrical (wall) outlet.

2.While holding the Handlebar (as if you were mowing) turn the Mower over on its right side to expose the Blade.

3.Place the 36mm Wrench over the Steel Hex Adapter (the large metal piece that holds the Blade in position) and place a 3/4" Socket or Wrench over the Blade Nut (Figure 29).

36mm Wrench

3/4" Wrench Figure 29

4.While holding the Hex Adapter in place, loosen the Blade Nut by turning counterclockwise. Be careful, hold the Hex Adapter firmly in place so that the Blade does not spin and strike your hand.

Hold the Wrenches at a slight angle to each other and squeeze together to avoid spinning the Blade. TIP Squeeze the 3/4" Wrench clockwise to tighten the Nut and counterclockwise to loosen the Nut.

5.Remove the Blade Nut, Steel Hex Adapter, Blade, and Steel Blade Adapter in that order (Figure 30).

6.To install a sharpened Blade or a new Blade, reverse the order of step 5. Be sure to replace all parts exactly as you removed them (Figure 30) and make sure to properly seat the Blade.

NOTE: Be sure that the stamping on the Blade “THIS SIDE TOWARDS MOWER” is facing the Mower. Also, if replacing the Blade with a new one, use the new Nut supplied. If you assemble the Blade more than ten (10) times, replace the Blade Nut with a new one.

7.Place the 36mm Wrench over the Steel Hex Adapter, then place a Torque Wrench with a 3/4" Socket over the Blade Nut (Figure 29) and while holding the Hex Adapter in place, tighten the Blade Nut by turning clockwise to 16.6 Ft-Lbs. Again, be careful, hold the Hex Adapter firmly in place so that the Blade does not spin and strike your hand.

8.Make sure the Blade is firmly attached, and then turn your Mower upright.

Sharpening the Blade

When the Blade is dull, the cut ends of the grass end up ragged and may turn brown soon after mowing. A dull blade also causes the Battery to discharge faster. When this occurs, sharpen the Blade (assuming the Blade is otherwise in good condition).

Tools and Supplies Needed:

•(See list on previous page)

•Fine-Toothed File or NEUTON Blade Sharpener (optional)

•Safety Glasses

•Vise

1.Remove the Blade (see steps 1 thru 5 above).

2.Secure the Blade in a sturdy Vise and while wearing Safety Glasses, carefully file the Cutting Edges of the Blade using even strokes. Be sure to file both sides and both ends equally.

TIP

Simply counting the number of strokes per edge will help to

 

keep the sharpening equal.

3.Check the blade after sharpening to be sure it is still balanced (see next page).

To

Mower

Blade Adapter

Hex Adapter

 

Blade Nut

Figure 30

 

 

 

38

1-866-NEUTON1 (638-8661) www.neutonpower.com

Page 41 Page 43
Image 42
Page 41 Page 43
Contents Battery-Powered Mower Safety & Operating InstructionsDirector, Customer Relations NEUTON→ Power EquipmentThank You Toll-Free phone 1-866-NEUTON1Table of Contents Optional MA 3.6 Trimmer and MA 5.6 Striper Roller About this Manual Introducing the Neuton Mower CEConventions used in this Manual Safety and Information Labels Important Safety ConsiderationsBattery Operating Tips Label Battery Insertion Label Protecting Yourself and Those around You Dressing AppropriatelyPreparing to Use Your Mower or Trimmer Operating Your Mower or Trimmer Safely Handling the Battery Safely Neuton Mower Package Checklist Setting Up Your Neuton MowerNEUTON1 Safety Key Read the Safety & Operating Instructions before proceeding Assembling Your Neuton MowerAdjust the Handlebar Height Remove the BatteryCharge the Battery before Your First Use Mulching Plug Rear Bagger Assembling the Bag to the Bag FrameInstalling the Bagger Removing and Emptying the BaggerInsert the Battery after Being Fully Charged Your Fully Assembled Neuton Mower ⇒ Power/Mode Switch Controls and Features⇒ Safety Key ⇒ Analog Voltage Gauge⇒ Status Indicator Light ⇒ Cutting Height LeverAnalog Voltage Gauge Neuton CE 6.2 Product Specifications Page Pre-Start Checks Operating Your Neuton MowerAdjusting the Cutting Height Mowing on SlopesCut Height Starting the Motor and Engaging the Blade Starting the MowerWhen Finished Mowing Stopping the Motor and BladeMowing and Lawn Care Tips Battery Charging and Caring for the BatteryCharging the Battery Charging the Battery in the MowerCharging with the Battery out of the Mower Disconnecting the ChargerRecharging after each use of the Mower Storage Temperature Range Recharging to Full Charge for Off-Season StorageCaring for the Battery Recycling your Used BatteryPage Striper Roller Spare BatteryNeuton Trimmer Spare Aero Cutting BladeBlade Sharpener Servicing Your Mower Servicing and Storing Your Neuton MowerCleaning Your Mower Cleaning the HandlebarSupplies Needed Removing and Attaching the Blade Tools and Supplies NeededSharpening the Blade Balancing the Blade Storing Your Neuton Mower Troubleshooting Table Troubleshooting TipsNEUTON1 638-8661 for assistance Mower is hard to push Optional MA 3.6 Trimmer and MA 5.6 Striper Roller Using the Neuton Trimmer Operating Your Trimmer SafelyTrimming on Slopes Safely Attaching, Removing and Using the Trimmer Attaching the TrimmerRemoving the Trimmer Adjusting the Trimmer Head Starting the Trimmer Stopping the TrimmerSafety Tips for using the Trimmer Advancing the CordReplacing the Spool Housing Maintaining and Storing the Neuton TrimmerReplacing the Spool Cleaning the Trimmer Attaching and Using the Striper RollerTool and Supplies Needed Page Parts List Neuton CE 6.2 Mower Parts Lists, Schematic Diagrams, and WarrantyDescription Qty Item # Description Qty Axle, Front 101 Washer, Lock w/Cap 120 Mesh, Bagger Schematic Diagrams Neuton CE 6.2 Mower 080111 Parts List Optional MA 3.6 Trimmer Schematic Diagram Optional MA 3.6 TrimmerItem # Description Qty Page Year Limited Warranty Terms and ConditionsTechnical Support Hotline Daily Checklist for your Neuton Mower At 1-866-NEUTON1

CE 6.2 specifications

The Neuton CE 6.2 is a cutting-edge electric lawn mower designed for home gardeners who value efficiency, eco-friendliness, and ease of use. This mower exemplifies modern landscaping technology, combining innovative features with user-friendly design elements to enhance the mowing experience.

One of the standout characteristics of the Neuton CE 6.2 is its impressive power-to-weight ratio. Weighing in at around 40 pounds, this electric mower strikes a balance between portability and performance. The lightweight design allows for effortless maneuverability, particularly in tight spaces and uneven terrains.

Equipped with a powerful 24-volt electric motor, the Neuton CE 6.2 delivers exceptional cutting performance while minimizing noise pollution and emissions. This makes it an excellent choice for eco-conscious users. The mower operates quietly, allowing users to mow at any time without disturbing neighbors or disrupting the peaceful environment of residential areas.

The Neuton CE 6.2 features an adjustable cutting deck, allowing users to customize the grass height settings. With cutting heights ranging from 1 inch to 3.5 inches, garden enthusiasts can achieve their desired lawn aesthetics with ease. The 16-inch cutting width provides ample coverage, enabling users to complete their mowing tasks efficiently while navigating around obstacles smoothly.

One of the most appealing aspects of the Neuton CE 6.2 is its cordless design. Powered by a rechargeable battery, this mower offers the convenience of not being tethered to a power outlet. The battery provides a substantial runtime, allowing users to mow larger lawns without frequent recharging interruptions. Additionally, the battery can be replenished quickly, ensuring that the mower is always ready for action.

The Neuton CE 6.2 also boasts a mulching capability, which allows users to recycle grass clippings back into the lawn. This practice not only nourishes the soil but also reduces the need for extensive bagging, presenting a more environmentally friendly option for yard maintenance.

In conclusion, the Neuton CE 6.2 electric lawn mower is an exceptional tool for modern gardeners seeking efficiency, performance, and sustainability. With its powerful yet quiet motor, adjustable cutting heights, cordless design, and mulching capabilities, it represents a significant step forward in lawn care technology, making it a valuable addition to any home's gardening arsenal.
Top Page Image Contents