MasterCraft 100524-01, CS-120CB owner manual Sharpening Cutters, Filing Cutter Depth Gauges

Page 13

CLEANING AND MAINTENANCE

Continued

Sharpening Cutters

Use file guide for 30° filing.

1.Adjust chain for proper tension (see Saw Chain Tension Adjustment, page 10).

2.Clamp guide bar in vise to hold saw steady. Note: Do not clamp chain.

3.Press four millimeter (5/32") round file (attached to file guide) into groove between top plate and depth gauge on chain. File guide should rest on both top plate and depth gauge (see Figures 20 and 21). Note: File at midpoint of guide bar.

4.Hold file guide level. Make sure 30° mark on file guide is parallel to center of guide bar (see Figure 20). This will insure that you file cutters at 30° angle.

5.File from inside towards outside of cutter until sharp. Only file in this one direction (see Figure 20). Note: Two or three strokes with file should sharpen cutter.

6.After each cutter if sharpened, move chain forward to sharpen next cutter. File all cutters on one side of chain.

7.Move to other side of chain and repeat process.

Filing

Direction

30° Guide

Mark

File Guide

 

Top Plate

Left Side

Groove (right side of chain)

 

of Chain

Depth Gauge

 

 

(left side

 

of chain)

Groove

Top Plate

Depth Gauge

(left side

(right side of chain)

of chain)

 

 

Right Side

 

of Chain

Figure 21 - Chain Part Locations

Filing Cutter Depth Gauges

The cutter depth gauge clearance is reduced as cutters are sharpened. After every second or third sharpening, reset cutter depth gauges.

1.Place depth gauge tool firmly across top of two cutters. Make sure depth gauge enters slot in depth gauge tool (see Figure 22).

2.Use medium flat file. File depth gauge level with depth gauge tool.

3.Remove depth gauge tool. With flat file, round off front corner of cutter depth gauge (see Figure 23).

Depth Gauge

4 mm (5/32") Round File

Note: This illustration shows file guide place- ment and filing direction for

Flat File

Depth

Gauge

Tool

Depth

Gauge

Slot

sharpening cutters on left side of chain.

Figure 20 - File and File Guide Placement On Chain

Figure 22 - Depth Gauge Tool On Chain

Front Corner

ECSp005

Figure 23 - Round Off Front Corner Of Depth Gauge

After several hand filings, have authorized service center or sharpening service machine sharpen chain. This will insure even filing.

100549

13

Continued

 

 

 

Page 12 Page 14
Image 13
Page 12 Page 14
Contents Chain Brake ContentsInformation SymbolsKickback Safety Devices On This Saw Safety WarningsBefore Operating Chain SAW Cause Of KickbackMaintenance and Storage of Chain SAW Saw Maintenance and Kickback SafetyPushback and PULL-IN Cause Of Pushback and Pull-InChain SAW Names and Terms Product IdentificationUnpacking Filling OIL TankExtension Cords Operating Chain SAWOiling Chain Cutting with the Chain SAWFelling a Tree Cutting Down a Tree Trimming a Tree PruningBefore Felling a Tree Retreat Path Direction of Fall TreeLimbing a Tree Felling Procedure1st Cut Inches Lower Notch CutLog Supported On One End Bucking a LOGEntire Length Of Log On Ground Log Supported On Both EndsGuide Bar Nuts Correct Tension Gap Incorrect Tension SAW Chain Tension AdjustmentSprocket Support Adjusting Block Plate Screw Guide Bar Nuts Sprocket Support Adjusting HoleReplacing Guide BAR / SAW Chain Saw Drive Chain Sprocket Guide Bar BoltsCleaning SAW Body Cleaning and MaintenanceCare of Guide BAR Sharpening Your SAW ChainFiling Cutter Depth Gauges Sharpening CuttersStorage Replacement PartsReplacing Saw Chain Observed Fault Possible Cause Remedy TroubleshootingKeep this Warranty Warranty InformationMastercraft Electric Chain SAW Warranty Table DES Matières Frein DE ChaîneDescription SymbolesAvant D’UTILISER LA Tronçonneuse AvertissementRecul Cause du reculCauses de la poussé e et de la traction Poussé E ET TractionEntretien de la tronç onneuse et protection contre le recul Utilisation DE LA Tronç OnneuseEntretien ET Remisage DE LA Tronç Onneuse Vocabulaire DE LA Tronç Onneuse Nomenclature DES PIÈ CESRemplissageduré SERVOIRD’HUILE DÉ BallageUtilisation DE LA Tronç Onneuse Avertissement Frein DE Chaîne Utilisation DE LA Tronç OnneuseTaille D’UN Arbre É lagage Avant d’abattre un arbre Abattage D’UN ArbreProcé dure d’abattage Sifflet d’abattage Trait d’abattageDirection de la BranchageChute La bille est soutenue à une extré mité Tronç Onnage D’UNE BilleToute la bille repose au sol La bille est soutenue aux deux extré mité sCrous de lame-guide Lame-guide RÉ Glage DE LA Tension DE LA Chaîne AvertissementLame-guide Correcte Tension incorrecte Support de pignon Bloc de Plaque de Réglage Vis de réglage Remplacement DE L’ENSEMBLE LAME-GUIDE/CHAÎNENettoyage DU Carter DE Tronç Onneuse Nettoyage ET Entretien AvisEntretien normal de la lame-guide Entretien DE LA LAME-GUIDEAffû Tage DE LA Chaîne Nettoyage ET EntretienOutils né cessaires pour affû ter la chaîne Affû tage des taillantsRemisage Remplacement de la chaînePIÈ CES DE Rechange Avertissement Limage des limiteurs de profondeur des taillantsDÉ Faillance Observé E Cause Possible Remè DE DÉ Pannage Avertissement100549 100549 Conserver Cette Garantie Information SUR LA GarantieGarantie DE LA Tronç Onneuse É Lectrique Mastercraft

100524-01, CS-120CB specifications

The MasterCraft 100524-01, CS-120CB is a cutting-edge, high-performance machine tool designed for precision cutting and machining of various materials. This advanced equipment is particularly favored in the manufacturing and fabrication industries due to its reliability, efficiency, and exceptional quality of output.

One of the primary features of the CS-120CB is its robust construction. Built with high-grade materials, the machine offers impressive stability and durability, making it suitable for continuous operation in demanding environments. This stability reduces vibrations, ensuring that the cutting process remains precise, which is crucial for producing high-quality parts.

Another standout characteristic of the CS-120CB is its powerful motor. With a strong, energy-efficient motor, the machine can easily tackle tough materials such as metals, plastics, and composites. This versatility allows operators to expand their capabilities and produce an array of products, from intricate components to larger workpieces.

The MasterCraft 100524-01 is also equipped with sophisticated control technologies. Its user-friendly interface allows for easy programming and operation, ensuring that both experienced and novice operators can utilize the machine effectively. The advanced numerical control system enhances accuracy by allowing for intricate designs and repeatable precision results.

Another innovative feature of the CS-120CB is its automated tool changers. This technology significantly reduces downtime, as the machine can switch between various tools on its own without requiring manual intervention. This capability is particularly advantageous in high-volume production settings, where time savings can directly impact profitability.

Additionally, the MasterCraft 100524-01 incorporates safety features to protect the operator and the work environment. Emergency stop buttons, protective guards, and safety interlocks are standard, ensuring that the machine is not only efficient but also safe for continual use.

In summary, the MasterCraft 100524-01, CS-120CB is a premier choice for industries that demand precision machining and cutting capabilities. With its robust construction, powerful motor, advanced control technologies, automated tool changers, and extensive safety features, this machine stands as a reliable asset for enhancing productivity and quality in manufacturing processes. Its adaptability to various materials further solidifies its position as a leading machine tool in the market.
Top Page Image Contents