MasterCraft 100524-01, CS-120CB owner manual Bucking a LOG, Log Supported On One End

Page 9

OPERATING CHAIN SAW

Continued

BUCKING A LOG

!WARNING

Avoid kickback. Kickback can result in severe injury or death. See Kickback, page 3 to avoid risk of kickback.

!WARNING

•If on slope, make sure log will not roll down hill. Secure log by using wooden stakes. Drive wooden stakes into ground on downhill side of log. Stand on uphill side of log while cutting. Log may roll after cutting.

•Never try cutting through two logs at same time. This could increase the risk of kickback.

•While cutting log, never hold log with your hand, leg, or foot.

•While cutting log, never allow another person to hold log.

•Turn off and unplug saw before moving from one place to another.

Log Supported On One End

1.Make first cut on underside of log (see Figure 12). Use top of guide bar to make this cut. Cut 1/3 through diameter of log. This cut will keep section from splintering when cut.

2.Make second cut directly above first cut. Cut down to meet first cut. This cut will keep log from pinching guide bar and chain.

2nd Cut

1st Cut

Figure 12 - Bucking Log When Log Is Supported

On One End

!CAUTION

Seek professional help if facing conditions beyond your ability.

Bucking a log is cutting a log into sections. Make sure your footing is firm. Keep feet apart. Divide your weight evenly on both feet. Stand slightly to left of saw. This keeps your body from being in direct line with chain. When possible, raise log or section off ground. Do this by using limbs, logs, chocks, etc.

When cutting through log, maintain control by reducing cutting pressure near end of cut. Do not relax your grip on chain saw handles. Do not let moving chain touch ground. Ground will dull moving chain. After cutting through log, release trigger to turn saw off before moving saw.

Follow directions below to buck a log.

Entire Length Of Log On Ground

Cut log from top (see Figure 11).

Figure 11 - Bucking Log With Entire Length On Ground

Log Supported On Both Ends

1.Make first cut from above log (see Figure 13). Cut 1/3 through diameter of log. This cut will keep section from splintering when cut.

2.Make second cut on underside of log, directly under first cut. Use top of guide bar to make this cut. Cut up to meet first cut. This will keep log from pinching guide bar and chain.

1st Cut

2nd Cut

Figure 13 - Bucking Log When Log Is Supported

On Both Ends

100549

9

 

Page 8 Page 10
Image 9
Page 8 Page 10
Contents Chain Brake ContentsInformation SymbolsKickback Safety Devices On This Saw Safety WarningsBefore Operating Chain SAW Cause Of KickbackMaintenance and Storage of Chain SAW Saw Maintenance and Kickback SafetyPushback and PULL-IN Cause Of Pushback and Pull-InChain SAW Names and Terms Product IdentificationUnpacking Filling OIL TankExtension Cords Operating Chain SAWOiling Chain Cutting with the Chain SAWFelling a Tree Cutting Down a Tree Trimming a Tree PruningBefore Felling a Tree Retreat Path Direction of Fall TreeLimbing a Tree Felling Procedure1st Cut Inches Lower Notch CutLog Supported On One End Bucking a LOGEntire Length Of Log On Ground Log Supported On Both EndsGuide Bar Nuts Correct Tension Gap Incorrect Tension SAW Chain Tension AdjustmentSprocket Support Adjusting Block Plate Screw Guide Bar Nuts Sprocket Support Adjusting HoleReplacing Guide BAR / SAW Chain Saw Drive Chain Sprocket Guide Bar BoltsCleaning SAW Body Cleaning and MaintenanceCare of Guide BAR Sharpening Your SAW ChainFiling Cutter Depth Gauges Sharpening CuttersReplacement Parts StorageReplacing Saw Chain Observed Fault Possible Cause Remedy TroubleshootingWarranty Information Keep this WarrantyMastercraft Electric Chain SAW Warranty Table DES Matières Frein DE ChaîneDescription SymbolesAvant D’UTILISER LA Tronçonneuse AvertissementRecul Cause du reculCauses de la poussé e et de la traction Poussé E ET TractionEntretien de la tronç onneuse et protection contre le recul Utilisation DE LA Tronç OnneuseEntretien ET Remisage DE LA Tronç Onneuse Vocabulaire DE LA Tronç Onneuse Nomenclature DES PIÈ CESDÉ Ballage Remplissageduré SERVOIRD’HUILEUtilisation DE LA Tronç Onneuse Avertissement Utilisation DE LA Tronç Onneuse Frein DE ChaîneTaille D’UN Arbre É lagage Avant d’abattre un arbre Abattage D’UN ArbreProcé dure d’abattage Sifflet d’abattage Trait d’abattageBranchage Direction de laChute La bille est soutenue à une extré mité Tronç Onnage D’UNE BilleToute la bille repose au sol La bille est soutenue aux deux extré mité sRÉ Glage DE LA Tension DE LA Chaîne Avertissement Crous de lame-guide Lame-guideLame-guide Correcte Tension incorrecte Support de pignon Bloc de Plaque de Réglage Vis de réglage Remplacement DE L’ENSEMBLE LAME-GUIDE/CHAÎNENettoyage DU Carter DE Tronç Onneuse Nettoyage ET Entretien AvisEntretien normal de la lame-guide Entretien DE LA LAME-GUIDEAffû Tage DE LA Chaîne Nettoyage ET EntretienOutils né cessaires pour affû ter la chaîne Affû tage des taillantsRemisage Remplacement de la chaînePIÈ CES DE Rechange Avertissement Limage des limiteurs de profondeur des taillantsDÉ Faillance Observé E Cause Possible Remè DE DÉ Pannage Avertissement100549 100549 Information SUR LA Garantie Conserver Cette GarantieGarantie DE LA Tronç Onneuse É Lectrique Mastercraft

100524-01, CS-120CB specifications

The MasterCraft 100524-01, CS-120CB is a cutting-edge, high-performance machine tool designed for precision cutting and machining of various materials. This advanced equipment is particularly favored in the manufacturing and fabrication industries due to its reliability, efficiency, and exceptional quality of output.

One of the primary features of the CS-120CB is its robust construction. Built with high-grade materials, the machine offers impressive stability and durability, making it suitable for continuous operation in demanding environments. This stability reduces vibrations, ensuring that the cutting process remains precise, which is crucial for producing high-quality parts.

Another standout characteristic of the CS-120CB is its powerful motor. With a strong, energy-efficient motor, the machine can easily tackle tough materials such as metals, plastics, and composites. This versatility allows operators to expand their capabilities and produce an array of products, from intricate components to larger workpieces.

The MasterCraft 100524-01 is also equipped with sophisticated control technologies. Its user-friendly interface allows for easy programming and operation, ensuring that both experienced and novice operators can utilize the machine effectively. The advanced numerical control system enhances accuracy by allowing for intricate designs and repeatable precision results.

Another innovative feature of the CS-120CB is its automated tool changers. This technology significantly reduces downtime, as the machine can switch between various tools on its own without requiring manual intervention. This capability is particularly advantageous in high-volume production settings, where time savings can directly impact profitability.

Additionally, the MasterCraft 100524-01 incorporates safety features to protect the operator and the work environment. Emergency stop buttons, protective guards, and safety interlocks are standard, ensuring that the machine is not only efficient but also safe for continual use.

In summary, the MasterCraft 100524-01, CS-120CB is a premier choice for industries that demand precision machining and cutting capabilities. With its robust construction, powerful motor, advanced control technologies, automated tool changers, and extensive safety features, this machine stands as a reliable asset for enhancing productivity and quality in manufacturing processes. Its adaptability to various materials further solidifies its position as a leading machine tool in the market.
Top Page Image Contents