Land Pride 357-187M manual Left Transaxle View of Oil Filter, Left Transaxle Inboard View

Page 36

Table of Contents

Section 5: Maintenance & Lubrication

Land Pride

5.Clean transaxle exterior and expansion tank of any debris. A degreaser may be needed.

NOTE: Drain old oil filters of all free flowing oil prior to disposal. Place used oil and oil filter in appropriate containers and deliver to an approved collection facility.

6.Move actuator arm (#2) out of the way and unscrew the used oil filter (#5). Be sure to properly dispose the filter.

7.Remove expansion tank cover (#11) to facilitate drainage.

8.Allow oil to drain until it has slowed to a slow drip. Be sure to properly dispose the oil.

9.After oil has completely drained, install a new oil filter per instructions below:

a.With a clean rag, clean the mounting surface that the filter seats against.

Park Brake

Lever Arm

24900

Left Transaxle (View of Oil Filter)

Figure 5-6

b.Apply a thin coat of oil on the rubber seal surface of the new filter (#5).

c.Screw filter on until it makes contact with the surface it seats against.

d.Tighten filter an additional 3/4 to 1 full turn more.

e.Install filter guard (#6) with three 1/4" screws (#7). Torque screws to 65 in-lbs.

f.Reattach actuator arm (#2) with clevis pin (#1), flat washer (#3) and hair pin cotter (#4) as shown.

10.Remove top port plug (#8). This will allow the transaxles to vent during oil fill.

11.Fill transaxle with oil by adding oil to the expansion tank (#10) until oil appears at the top port opening (approximately 2 qts.). See page 43 for transaxle oil specifications.

12.Install top port plug (#8). Tighten plug to 180 in-lbs. of torque.

13.Continue to add oil to the expansion tank until oil reaches the full cold line (approximately 1/2" up from the bottom of the tank).

NOTE: The fill tube (#9) should be hand squeezed several times to burp out air and to drain oil from the expansion tank into the tube. Be careful not to damage the tube while squeezing it. Use a protective cloth wrapped around the tube if using a tool to squeeze such as a pair of pliers.

14.Reinstall expansion tank cap (#11) by hand. Be careful to not overtighten.

15.Wipe off all excess oil. A degreaser may be needed to remove excess oil.

16.Repeat steps 1 thru 15 for the right side.

24900

Left Transaxle (Inboard View)

Figure 5-7

34 Z44 & Z52 (S/N 526171 & Above) Zero Turning Radius Mowers Riding Mowers Accu-Z Razor® 357-187M

1/12/09

Image 36

Contents Riding Mowers Accu-Z Razor Table of Contents Safety at All Times Practice Safe Maintenance Keep Riders Off MachineryAvoid High Pressure Fluids Hazard Prepare for Emergencies Wear Protective Equipment838-303C 818-543C838-306C 838-307C 838-308C 838-833C 838-310C 838-815C Using This Manual ApplicationOwner Assistance Control Lever Assembly Seat AssemblyHitch Plate Assembly Uncrating InstructionsNegative Black Negative Post Battery Cable Connecting the Negative CableElectrical Cable Connection Engine PreparationsMower Features Razor FeaturesMufﬂer Shield Is Located Under Engine Land PrideTable of Contents Blade Engagement Switch Left/Right Fuel Tank ValveControl Levers Refer to -4and FigureSafety Start Interlock System Deck Height Deck Lift Locking Pin Pedal IndicatorEngine Starting Deck Lift PedalDriving the Mower To Decrease Speed and StopTo Start and Increase Speed To SteerMoving the mower with a good battery Moving the mower with a bad batteryMoving Mower with Stalled Engine Refer to -6 onSafe Operating Instructions Discharge Chute Blade Engagement Switch Mower Deck OperationGeneral Operating Information BladeControl Lever Steering Adjustments Torque ValuesControl Lever Neutral Adjustment Adjust Pump Linkage Rods Jam Nuts At This Location OnlyFan Mounting Hardware 3-Places Steering Control LinkageForward Stop Adjustment Adjust Lever Stops to Protect PumpsAdjust Lever Stops to Drive Straight Steering DampenerSeat Adjustment Upper Control Lever AdjustmentsHydro-Drive Belt Adjustment Deck Drive Belt Adjustment Engine RPM SettingDeck Leveling & Height Adjustment Deck Level AdjustmentsRefer to -10& Figure Refer to -11 on Deck Cutting Height Adjustment Anti-Scalp RollersPivot Front Wheels Refer to -13 onSnow Plow Light KitMulching Kit Armrest for Standard SeatGrass Catcher Maintenance Locations Deck Bottom ViewBottom View Drive motors removed for clarity Maintenance Schedule Service at Intervals Indicated Every Refer to HoursMaintenance Battery Wiring Harness FussesTires Electrical SystemHydrostatic Drive System Transaxle Oil and Filter ChangeRefer to -6 & -7 on Left Transaxle View of Oil Filter Left Transaxle Inboard ViewTransaxle Purging Procedures Fuel SystemGeneral Engine Maintenance Fuel FilterDraining The Fuel Tank Engine Air FilterBelt Replacement Deck Belt Replacement InstructionsOil Check, Honda Engine Oil Check, Briggs & Stratton EngineHydro-Drive Belt Replacement Instructions Reference -12 & FigureRefer to -12 & Figure Hydro-Drive Belt RemovalMower Blade Maintenance Blade InspectionBlade Sharpening Refer to -16and FigureStorage Preparation of Engine for StorageNew Season Preparation Lubrication Points HoursCenter Blade Spindle Left Blade Spindle100/M Hours Caster Wheel Bearing ZerkFront Axle Center Pivot Deck Lift Pivot PointsZ44 & Z52 Accu-Z Razor S/N 526171+ Engine Specifications Hydrostatic Transmission SpecificationsGeneral Specifications Brake Service Safety FeaturesDeck Housing Depth IndicatorsFeatures Benefits Z44 & Z52 Accu-Z Razor S/N 526171+For the operator Steering levers designed for Oriented for maximumLoss of power or system will not operate Engine cranks but does not startEngine Either directionMower creeps when steering control Mower creeps when in parkRunning High oil consumptionTorque Values Chart Tire Inflation ChartAdditional Torque Values In-tpi Ft-lb Mm x pitch · mWarranty Corporate Ofﬁce P.O. Box Salina, Kansas 67402-5060 USA