Land Pride 357-187M manual Hydro-Drive Belt Replacement Instructions, Reference -12 & Figure

Page 40

Table of Contents

Section 5: Maintenance & Lubrication

Land Pride

9.Re-tension idler pulley (#4) by turning the over- center-release bolt (#9) clockwise. Tension belt per “Deck Drive Belt Adjustment” section on page 23.

10.Re-install hitch pin (#10).

11.Re-install deck belt covers.

12.Re-attach the negative battery cable and floor panel.

Hydro-Drive Belt Replacement Instructions

Refer to Figure 5-12 & Figure 5-13:

1.Park unit on a flat surface. Stop engine and remove ignition key. Make sure blade engagement switch is in the down (OFF) position. Spread control levers fully apart.

!WARNING

Make sure engine and muffler are completely cooled before working on and around the hydro-drive belt. Server burns to the body could result if engine and muffler have not cooled.

2.Disconnect negative battery cable.

3.Place deck height in the lowest position.

NOTE: Do not remove deck belt from the mower. Only remove it from the electric clutch pulley.

4.Remove deck drive belt (#8) from electric clutch pulley (#3) as outlined in steps 3 to 7 on page 37 under “Deck Belt Replacement Instructions”.

5.Release hydro-drive belt tension by loosening one of the two idler pulley bolts (#5) and moving that idler pulley (#4) completely back.

6.Slide hydro-drive belt off of idler pulleys (#4) and transaxle pulleys (#7).

7.Remove hydro-drive belt from the engine pulley (#2) and then from the mower.

8.Install new hydro-drive belt by first sliding the belt onto both transaxles pulleys (#7) and then onto the engine pulley (#2).

9.Position the belt over the idler pulleys (#4) and slide the loosened idler pulley forward to take out any slack in the belt.

10.Check to make sure the hydro-drive belt (#1) is routed properly on all five pulleys.

NOTE: Belt tension can be checked with a Belt Tension Gauge available at most auto parts stores.

11.Tighten the loose idler pulley (#4) until belt (#1) has 30-50 lbs of tension. With drive belt properly tensioned, tighten idler bolts (#5) to the correct torque.

12.Re-tension deck drive belt per following steps 8 to 11 on page 37 under “Deck Belt Replacement Instructions”.

13.Re-attach the negative battery cable and floor panel.

 

7

 

 

 

6

1

5

4

 

2

3

 

 

24901

Hydro-Drive Belt Viewed from the Bottom (Transaxles with pulleys removed for clarity) Figure 5-12

 

Drive Belt (#1) on

 

Engine Pulley (#2)

 

Deck Belt (#8) on

 

Clutch Pulley (#3)

3

2

 

 

1

 

8

 

24905

Hydro-Drive Belt Removal

Figure 5-13

Reference Figure 5-12 & Figure 5-13

1.

Hydro-drive belt

6.

Access hole to idler

2.

Engine pulley

 

pulleys

7.

Pump pulleys location

3.

Electric clutch pulley

 

(Not shown for clarity)

4.

Pump idler pulleys

 

8.

Deck drive belt

5.

Mounting bolts,

 

 

idler pulley

38 Z44 & Z52 (S/N 526171 & Above) Zero Turning Radius Mowers Riding Mowers Accu-Z Razor® 357-187M

1/12/09

Page 39 Page 41
Image 40
Page 39 Page 41
Contents Riding Mowers Accu-Z Razor Table of Contents Safety at All Times Keep Riders Off Machinery Practice Safe MaintenanceAvoid High Pressure Fluids Hazard Prepare for Emergencies Wear Protective Equipment818-543C 838-303C838-306C 838-307C 838-308C 838-833C 838-310C 838-815C Application Using This ManualOwner Assistance Control Lever Assembly Seat AssemblyHitch Plate Assembly Uncrating InstructionsNegative Black Negative Post Battery Cable Connecting the Negative CableElectrical Cable Connection Engine PreparationsRazor Features Mower FeaturesMuffler Shield Is Located Under Engine Land PrideTable of Contents Blade Engagement Switch Left/Right Fuel Tank ValveControl Levers Refer to -4and FigureSafety Start Interlock System Deck Height Deck Lift Locking Pin Pedal IndicatorEngine Starting Deck Lift PedalDriving the Mower To Decrease Speed and StopTo Start and Increase Speed To SteerMoving the mower with a good battery Moving the mower with a bad batteryMoving Mower with Stalled Engine Refer to -6 onSafe Operating Instructions Discharge Chute Blade Engagement Switch Mower Deck OperationGeneral Operating Information BladeControl Lever Steering Adjustments Torque ValuesControl Lever Neutral Adjustment Adjust Pump Linkage Rods Jam Nuts At This Location OnlyFan Mounting Hardware 3-Places Steering Control LinkageForward Stop Adjustment Adjust Lever Stops to Protect PumpsAdjust Lever Stops to Drive Straight Steering DampenerUpper Control Lever Adjustments Seat AdjustmentHydro-Drive Belt Adjustment Deck Drive Belt Adjustment Engine RPM SettingDeck Leveling & Height Adjustment Deck Level AdjustmentsRefer to -10& Figure Refer to -11 on Deck Cutting Height Adjustment Anti-Scalp RollersPivot Front Wheels Refer to -13 onSnow Plow Light KitMulching Kit Armrest for Standard SeatGrass Catcher Deck Bottom View Maintenance LocationsBottom View Drive motors removed for clarity Maintenance Schedule Service at Intervals Indicated Every Refer to HoursMaintenance Battery Wiring Harness FussesTires Electrical SystemTransaxle Oil and Filter Change Hydrostatic Drive SystemRefer to -6 & -7 on Left Transaxle View of Oil Filter Left Transaxle Inboard ViewTransaxle Purging Procedures Fuel SystemGeneral Engine Maintenance Fuel FilterDraining The Fuel Tank Engine Air FilterBelt Replacement Deck Belt Replacement InstructionsOil Check, Honda Engine Oil Check, Briggs & Stratton EngineHydro-Drive Belt Replacement Instructions Reference -12 & FigureRefer to -12 & Figure Hydro-Drive Belt RemovalMower Blade Maintenance Blade InspectionBlade Sharpening Refer to -16and FigurePreparation of Engine for Storage StorageNew Season Preparation Lubrication Points HoursCenter Blade Spindle Left Blade Spindle100/M Hours Caster Wheel Bearing ZerkFront Axle Center Pivot Deck Lift Pivot PointsHydrostatic Transmission Specifications Z44 & Z52 Accu-Z Razor S/N 526171+ Engine SpecificationsGeneral Specifications Brake Service Safety FeaturesDeck Housing Depth IndicatorsFeatures Benefits Z44 & Z52 Accu-Z Razor S/N 526171+For the operator Steering levers designed for Oriented for maximumLoss of power or system will not operate Engine cranks but does not startEngine Either directionMower creeps when steering control Mower creeps when in parkRunning High oil consumptionTorque Values Chart Tire Inflation ChartAdditional Torque Values In-tpi Ft-lb Mm x pitch · mWarranty Corporate Office P.O. Box Salina, Kansas 67402-5060 USA
Top Page Image Contents