Land Pride 357-187M manual Uncrating Instructions, Control Lever Assembly, Seat Assembly

Page 10

Table of Contents

Section 1: Assembly & Set-up

NOTE: For correct torque values, refer to “Torque Values Chart” on page 48.

Uncrating Instructions

The crate is assembled with nails and the mower frame is secured to the crate floor with metal bands.

1.First, pry off the top panel and then the side panels and then the end panels.

2.Cut and remove metal bands securing front and rear wheels to the crate floor. Discard bands.

3.Complete assembly instructions and engine preparations below before driving mower off the crate floor.

Control Lever Assembly

Refer to Figure 1-1:

Control levers (#1A & #1B) are factory shipped rotated down and secured with bolts in control levers.

1.Loosen bolt (#3B) on upper right control lever (#1R).

2.Remove bolt (#3A) from lower control lever (#9R).

3.Rotate control lever up until slot in upper control lever aligns with hole in lower control lever.

4.Reinstall 3/8"-16 1 1/2" GR5 hex head bolt (#3A) and 3/8" hex flange lock nut (#2).

5.Repeat steps 1 to 4 for the left control lever (#1L).

6.Align control lever handles with each other and tighten bolts (#3A & #3B) to the correct torque.

NOTE: See "Upper Control Lever Adjustments" on page 22 for final adjustments to the control levers.

Seat Assembly

Refer to Figure 1-1:

Seat (#4) is shipped mounted to hinge platform (#5) and attached to the shipping crate with lag bolts.

IMPORTANT: Be careful not to cut the seat cover when removing packing material around the seat. Cutting the seat cover will void its warranty.

IMPORTANT: The arm rests on the Deluxe Seat must be pivoted up when attaching the seat platform to the mower deck. Leaving arm rests down while attaching the seat platform can cut the arm rest covers and void the warranty.

1.Remove the two lag bolts securing seat (#4) and platform (#5) to the shipping crate.

2.Spread control levers (#1) fully apart and pivot deluxe seat arm rest up.

3.Mount seat platform to hinge tabs at the front with two 5/16”-18 x 5/8” lg. GR5 bolts (#6) and two hex flange locknuts (#7). Tighten nuts snugly to remove all play and then back nuts up one-quarter turn.

4.Locate and connect mower switch wires to the operator pressure switch under the seat.

5.Hinge the seat platform down and secure in place with two 5/16"-18 x 3/4" lg. phillips head machine screws (#8).

6.The seat platform is slotted so the seat can be adjusted to fit the operator. See "Seat Adjustment" on page 22 for positioning.

24896

Control Lever & Seat Assembly

(Standard Seat Assembly Shown)

Figure 1-1

Hitch Plate Assembly

Refer to Figure 1-2:

Hitch plate (#1) is shipped mounted to the mower’s rear bumper ready for use. If not, the plate will need to be removed, turned around and remounted as follows:

1.Remove two 5/16"-18 x 5/8" GR5 hex flange screws (#2) and hitch plate (#1) from under the bumper.

2.Rotate and reinstall hitch plate (#1) as shown with existing 5/16"-18 x 5/8" GR5 hex head flange screws.

3.Tighten 5/16" hex head flange screws (#2) to the correct torque.

23624

Hitch Plate Assembly

Figure 1-2

8

Z44 & Z52 (S/N 526171 & Above) Zero Turning Radius Mowers Riding Mowers Accu-Z Razor® 357-187M

1/12/09

Page 9 Page 11
Image 10
Page 9 Page 11
Contents Riding Mowers Accu-Z Razor Table of Contents Safety at All Times Keep Riders Off Machinery Practice Safe MaintenanceAvoid High Pressure Fluids Hazard Prepare for Emergencies Wear Protective Equipment818-543C 838-303C838-306C 838-307C 838-308C 838-833C 838-310C 838-815C Application Using This ManualOwner Assistance Hitch Plate Assembly Control Lever AssemblySeat Assembly Uncrating InstructionsElectrical Cable Connection Negative Black Negative Post Battery CableConnecting the Negative Cable Engine PreparationsRazor Features Mower FeaturesMuffler Shield Is Located Under Engine Land PrideTable of Contents Control Levers Blade Engagement SwitchLeft/Right Fuel Tank Valve Refer to -4and FigureEngine Starting Safety Start Interlock SystemDeck Height Deck Lift Locking Pin Pedal Indicator Deck Lift PedalTo Start and Increase Speed Driving the MowerTo Decrease Speed and Stop To SteerMoving Mower with Stalled Engine Moving the mower with a good batteryMoving the mower with a bad battery Refer to -6 onSafe Operating Instructions Discharge Chute General Operating Information Blade Engagement SwitchMower Deck Operation BladeControl Lever Steering Adjustments Torque ValuesFan Mounting Hardware 3-Places Control Lever Neutral AdjustmentAdjust Pump Linkage Rods Jam Nuts At This Location Only Steering Control LinkageAdjust Lever Stops to Drive Straight Forward Stop AdjustmentAdjust Lever Stops to Protect Pumps Steering DampenerUpper Control Lever Adjustments Seat AdjustmentHydro-Drive Belt Adjustment Deck Leveling & Height Adjustment Deck Drive Belt AdjustmentEngine RPM Setting Deck Level AdjustmentsRefer to -10& Figure Refer to -11 on Pivot Front Wheels Deck Cutting Height AdjustmentAnti-Scalp Rollers Refer to -13 onMulching Kit Snow PlowLight Kit Armrest for Standard SeatGrass Catcher Deck Bottom View Maintenance LocationsBottom View Drive motors removed for clarity Maintenance Schedule Service at Intervals Indicated Every Refer to HoursMaintenance Tires BatteryWiring Harness Fusses Electrical SystemTransaxle Oil and Filter Change Hydrostatic Drive SystemRefer to -6 & -7 on Left Transaxle View of Oil Filter Left Transaxle Inboard ViewTransaxle Purging Procedures Fuel SystemDraining The Fuel Tank General Engine MaintenanceFuel Filter Engine Air FilterOil Check, Honda Engine Belt ReplacementDeck Belt Replacement Instructions Oil Check, Briggs & Stratton EngineRefer to -12 & Figure Hydro-Drive Belt Replacement InstructionsReference -12 & Figure Hydro-Drive Belt RemovalBlade Sharpening Mower Blade MaintenanceBlade Inspection Refer to -16and FigurePreparation of Engine for Storage StorageNew Season Preparation Center Blade Spindle Lubrication PointsHours Left Blade SpindleFront Axle Center Pivot 100/M HoursCaster Wheel Bearing Zerk Deck Lift Pivot PointsHydrostatic Transmission Specifications Z44 & Z52 Accu-Z Razor S/N 526171+ Engine SpecificationsGeneral Specifications Deck Housing Depth Brake ServiceSafety Features IndicatorsFor the operator Steering levers designed for Features BenefitsZ44 & Z52 Accu-Z Razor S/N 526171+ Oriented for maximumEngine Loss of power or system will not operateEngine cranks but does not start Either directionRunning Mower creeps when steering controlMower creeps when in park High oil consumptionAdditional Torque Values Torque Values ChartTire Inflation Chart In-tpi Ft-lb Mm x pitch · mWarranty Corporate Office P.O. Box Salina, Kansas 67402-5060 USA
Top Page Image Contents