Land Pride RC35120 RCM35120 manual Pull-Type Tractor Hook-Up

Page 15

Land Pride

Section 1 Assembly and Setup

Pull-Type Cutter

Refer to Figure 1-10:

1.Back off leveling rod jam nut, (#16) and leveling tube nut (#15) on leveling rod.

2.Raise tongue off the ground manually and support tongue with screw jack.

3.Back the tractor up to the tongue until holes in drawbar and cutter hitch are aligned.

4.Attach cutter with 1 1/4” hitch pin and secure with lock pin. Always use a pin that contains a safety locking de- vice to prevent it from falling out.

5.Place tongue jack in a horizontal position on the jack mount located on the left front of cutter deck.

6.Tighten leveling tube nut until it bottoms out on trun- nion. Turn nut additional 2 or 3 turns and tighten jam nut.

7.Connect cylinder hoses to tractor remote outlets.

8.Attach safety chain on tongue hitch to tractor and lock hook securely on chain. Adjust chain length to remove all slack except what is necessary to permit turning of the cutter.

9.Slide PTO shaft over tractor’s splined shaft and secure with locking device of PTO shaft.

10.Secure chain on PTO around cutter tongue to restrict outer shield of PTO from rotating. Leave adequate length of chain loose for turning.

NOTE: Chain should be attached to PTO at imple- ment end of shaft.

11.PTO should now be moved back and forth to insure that it is secured on the shaft of the tractor and stub shaft on the cutter.

12.Should the PTO shaft require shortening:

Refer back to Figure 1-8:

a.Hold the shafts next to each other in the shortest working position and mark them.

b.Shorten inner and outer guard tubes equally.

c.Shorten inner and outer sliding profiles by the same length as the guard tubes.

d.Proper overlap is a minimum of one-half the length of each tube, with both tubes being of equal length.

e.Round off all sharp edges and remove burrs. Grease sliding profiles.

14262

Pull-Type Tractor Hook-Up

Figure 1-10

11/16/00

RC35120 RCM35120 Rotary Cutter 312-301M

13

Page 14 Page 16
Image 15
Page 14 Page 16
Contents RC35120 RCM35120 Operator’s t ’s Manual lTable of Contents Important Safety Information 818-130C 818-161C818-187C 818-187C 818-229C 818-230C818-240C 818-554C 818-552C818-555C 818-556C 818-557C Owner Assistance Using This ManualHitch & Axle Assembly Tractor RequirementsLift-Type Cutter Refer back to Figure TailwheelTongue Pull-Type CutterLeveling Rod Rear AxleLift-Type Cutter Driveline InstallationSafety Guards Tractor Hook-UpIf check chain kit is purchased, assemble to cutter Pull-Type Tractor Hook-Up Transporting Operating Check ListCutting Instructions Operating Instructions Deck Attitude Adjustment Lift-Type Cutting HeightPull-Type Cutting Height Clutch slipping Problem Cause Solution Oil seal leakingDriveline yoke or cross failing DrivelineProblem Cause Solution Excessive vibration Flex Couplers MaintenanceSkid Shoe Service & Replacement Service Cutting BladesPivoting Upper Hitch StorageClutch Run-In LubricationDriveline U-Joints Lift-Type Tailwheel HubPull-Type Tailwheel Hub Ratchet JackDriveline GearboxBox Assembly Plate Slip Clutch DisassemblySpecifications and Capacities Appendix Torque Values Chart for Common Bolt SizesWarranty Great Plains Manufacturing, Inc

RC35120 RCM35120 specifications

The Land Pride RC35120, part of the RCM35120 series, stands out in the agriculture and landscaping sectors for its robust design and exceptional performance. This remote-controlled mower is engineered to handle a variety of mowing tasks with precision and ease, making it a popular choice among professionals and hobbyists alike.

One of its main features is the powerful engine that drives the RC35120, providing ample horsepower to tackle tough terrain and thick grass. The mower's high-performance engine ensures that it can operate efficiently even in challenging conditions, making it a reliable option for extensive landscaping projects.

The RC35120 is equipped with an advanced remote control system that allows operators to maneuver the mower from a safe distance. This feature is especially beneficial in hazardous or difficult-to-reach areas, as it reduces the risk of injury and increases operational efficiency. The ergonomic remote control design is intuitive, allowing users to adjust speed and direction with ease, enabling precise navigation around obstacles.

Another key characteristic of the RC35120 is its high-quality cutting deck. The mower features a reinforced deck that provides durability and longevity, capable of withstanding the rigors of regular use. The cutting height can be easily adjusted, allowing for flexibility in mowing preferences and different grass types. With a cutting width of 35 inches, the RC35120 allows operators to cover large areas swiftly, ultimately saving time and reducing labor costs.

Additionally, the RC35120 incorporates safety features that enhance both usage and operational peace of mind. The mower is built with protective guards to shield the operator from debris while mowing. Furthermore, automatic shut-off systems are implemented to halt operation in the event of a malfunction, promoting safety during use.

In terms of technology, the RC35120 integrates modern features such as easy maintenance access and an effective cooling system that ensures the engine stays within optimal temperature ranges during operation. These attributes not only prolong the life of the mower but also improve overall performance.

In summary, the Land Pride RC35120 RCM35120 mower is an exceptional tool that combines power, efficiency, and safety. Its innovative design, robust features, and advanced technologies make it an ideal choice for anyone looking to enhance their landscaping capabilities with a top-tier remote-controlled mower. Whether for commercial use or personal landscaping, this model delivers reliability and exceptional results.
Top Page Image Contents