Land Pride RC35120 RCM35120 Maintenance, Skid Shoe Service & Replacement, Service Cutting Blades

Page 21

Land Pride

Section 5 Maintenance and Lubrication

Section 5 Maintenance and Lubrication

Maintenance

Proper servicing and adjustment is the key to the long life of

any farm implement. With careful and systematic inspec-

! CAUTION!

tion, you can avoid costly maintenance, time and repair.

Engage parking brake, disengage PTO, shut off tractor, and re-

After using your Rotary Cutter for several hours, check all

move key before making any of the following adjustments.

 

bolts to be sure they are tight.

Skid Shoe Service & Replacement

Replace any worn, damaged or illegible safety decals by

1. Check skid runners and skid shoes for wear and re-

obtaining new decals from your Land Pride Dealer.

Service Cutting Blades

place if necessary. Order skid shoe Land Pride part #

312-175D or 312-079A (1 set with hardware).

1. Both blades on each dishpan should be sharpened at

 

the same angle as the original cutting edge and must be replaced or reground at the same time to maintain proper balance in the cutting unit.

NOTE: Replace blades with genuine Land Pride parts only.

NOTE: Care should be taken in order not to remove any more material than necessary when sharpening blades.

2.Both blades on each dishpan should weigh the same after sharpening.

3.When replacing or sharpening the cutter blades, exam- ine bolts for excessive wear and replace if necessary. To replace blades:

a.Order blade bolt Land Pride part # 802-277C, clockwise blade part # 820-076C, and counter- clockwise blade part # 820-075C.

b.Torque blade bolt lock nut to 450 ft. pounds. An ex- tended cheater bar may be required to achieve proper torque.

c.Carefully check the cutting edges of the blades in relation to the blade carrier rotation, below to insure correct blade placement.

4.Blade dishpan replacement:

Refer to Figure 5-1:

a.Blades must be indexed 90˚ to one another to pre- vent blade collision.

b.Dishpan nut on gearbox output shafts should be torqued to 450 ft. pounds and cotter pin installed in nut with legs bent around.

!WARNING!

Excessive wear on skids may cause inadequate operation of cut- ter and create a safety hazard!

2.Plow bolts should be checked for wear and replaced if necessary. Order Land Pride part # 802-020C.

Refer to Figure 5-2:

3.To replace skid shoes:

a.Remove existing skid shoes.

b.Attach skid shoe to cutter, using four 3/8” plow bolts, flat washers and lock nuts.

c.Repeat on opposite side of cutter.

14270

Skid Shoe Replacement

Figure 5-2

Flex Couplers

Refer to Figure 5-3:

1.Disks (#1) and beaded washers (#2) should be re- placed if disassembling flex coupler shaft.

2.When replacing disks; bolts (#3) and nuts (#4) should be tightened evenly with nuts torqued 35 to 40 ft. pounds. Beaded washers (#4) should be imbedded

Blade Rotation

Figure 5-1

11/16/00

RC35120 RCM35120 Rotary Cutter 312-301M

19

Page 20 Page 22
Image 21
Page 20 Page 22
Contents RC35120 RCM35120 Operator’s t ’s Manual lTable of Contents Important Safety Information 818-130C 818-161C818-187C 818-187C 818-229C 818-230C818-240C 818-554C 818-552C818-555C 818-556C 818-557C Owner Assistance Using This ManualHitch & Axle Assembly Tractor RequirementsLift-Type Cutter Refer back to Figure TailwheelTongue Pull-Type CutterLeveling Rod Rear AxleSafety Guards Driveline InstallationTractor Hook-Up Lift-Type CutterIf check chain kit is purchased, assemble to cutter Pull-Type Tractor Hook-Up Transporting Operating Check ListCutting Instructions Operating Instructions Deck Attitude Adjustment Lift-Type Cutting HeightPull-Type Cutting Height Driveline yoke or cross failing Problem Cause Solution Oil seal leakingDriveline Clutch slippingProblem Cause Solution Excessive vibration Skid Shoe Service & Replacement MaintenanceService Cutting Blades Flex CouplersClutch Run-In StorageLubrication Pivoting Upper HitchPull-Type Tailwheel Hub Lift-Type Tailwheel HubRatchet Jack Driveline U-JointsDriveline GearboxBox Assembly Plate Slip Clutch DisassemblySpecifications and Capacities Appendix Torque Values Chart for Common Bolt SizesWarranty Great Plains Manufacturing, Inc

RC35120 RCM35120 specifications

The Land Pride RC35120, part of the RCM35120 series, stands out in the agriculture and landscaping sectors for its robust design and exceptional performance. This remote-controlled mower is engineered to handle a variety of mowing tasks with precision and ease, making it a popular choice among professionals and hobbyists alike.

One of its main features is the powerful engine that drives the RC35120, providing ample horsepower to tackle tough terrain and thick grass. The mower's high-performance engine ensures that it can operate efficiently even in challenging conditions, making it a reliable option for extensive landscaping projects.

The RC35120 is equipped with an advanced remote control system that allows operators to maneuver the mower from a safe distance. This feature is especially beneficial in hazardous or difficult-to-reach areas, as it reduces the risk of injury and increases operational efficiency. The ergonomic remote control design is intuitive, allowing users to adjust speed and direction with ease, enabling precise navigation around obstacles.

Another key characteristic of the RC35120 is its high-quality cutting deck. The mower features a reinforced deck that provides durability and longevity, capable of withstanding the rigors of regular use. The cutting height can be easily adjusted, allowing for flexibility in mowing preferences and different grass types. With a cutting width of 35 inches, the RC35120 allows operators to cover large areas swiftly, ultimately saving time and reducing labor costs.

Additionally, the RC35120 incorporates safety features that enhance both usage and operational peace of mind. The mower is built with protective guards to shield the operator from debris while mowing. Furthermore, automatic shut-off systems are implemented to halt operation in the event of a malfunction, promoting safety during use.

In terms of technology, the RC35120 integrates modern features such as easy maintenance access and an effective cooling system that ensures the engine stays within optimal temperature ranges during operation. These attributes not only prolong the life of the mower but also improve overall performance.

In summary, the Land Pride RC35120 RCM35120 mower is an exceptional tool that combines power, efficiency, and safety. Its innovative design, robust features, and advanced technologies make it an ideal choice for anyone looking to enhance their landscaping capabilities with a top-tier remote-controlled mower. Whether for commercial use or personal landscaping, this model delivers reliability and exceptional results.
Top Page Image Contents