Jonsered FC 2145 Assembly, Assembling the handlebar and throttle, Transport position, handlebar

Page 13

ASSEMBLY

Assembling the handlebar and throttle

(BC 2145)

•Remove the screw at the rear of the throttle handle.

•Slide the throttle handle onto the right side of the handlebar, (see diagram).

•Align the screw hole in the throttle handle with the hole in the handlebar.

•Reﬁt the screw in the hole in the rear of the throttle handle.

•Screw the screw through the handle and handlebar. Tighten it.

•Unscrew the knob from the handlebar mounting.

•Position the handlebar as shown. Fit the mounting components and tighten the knob lightly.

•Put on the harness and hang the machine from the support hook. Now make a ﬁnal adjustment so that the machine is in a comfortable working position when it hangs from the harness.

•Tighten the knob.

Assembling the handlebar and throttle

(FC 2145, FC 2145 S)

•Unscrew the knob from the handlebar mounting.

•Position the handlebar as shown. Fit the mounting components and tighten the knob lightly.

Fit the right handle to the handlebar using the screw, washer, sleeve and nut as shown. Tighten.

Put on the harness and hang the machine from the support hook. Now make a ﬁnal adjustment so that the machine is in a comfortable working position when it hangs from the harness.

Transport position, handlebar

•The handlebar can easily be turned to ﬁt along the shaft for easier transportation and storage.

•Loosen the knob.Turn the handlebar clockwise so that the throttle handle rests against the engine.

•Now twist the handlebar around the shaft. Tighten the knob.

•Fit the transport guard to the cutting attachment.

English – 13

Image 13

Contents Operator’s manual EPA Symbols KEY to SymbolsContents Dear customer IntroductionWhat is what on the clearing saw? BC What is WHAT?What is what on the clearing saw? FC 2145, FC 2145 S Personal protective equipment General Safety PrecautionsStop switch Machine′s safety equipmentThrottle lock Vibration damping system Cutting attachment guardQuick release MufﬂerLocking screw Locking nutCutting equipment Cutting equipmentSharpening grass cutters and grass blades Trimmer head Sharpening the saw bladeAssembling the handlebar and throttle AssemblyTransport position, handlebar FC 2145, FC 2145 SFitting blades and trimmer heads Fitting the trimmer guard and trimmer head Trimmy SII Fitting the blade guard and saw bladeFitting other guards and cutting attachments Adjusting the harness and clearing sawStandard harness Vector harness Adjusting the harnessCorrect balance Grass clearingFuel Handling Fuel safetyFuel Mixing FuelingCheck before starting Starting and StoppingStarting and stopping Cold engineStopping StartingWorking Techniques Basic safety rulesGeneral working instructions ABC of clearingWorking methods Forestry clearing using a saw bladeBrush cutting with a saw blade Grass clearing using a grass bladeTrimming Grass trimming with a trimmer headCarburetor MaintenanceCorrectly adjusted carburetor Fine adjustment of the idle speed TAdjusting the start throttle speed BC High speed jet HCooling system MufﬂerAir ﬁlter Bevel gear Cleaning the air ﬁlterDrive shaft Spark plugWinter use Temperature 0C 32F or colderMaintenance Daily Weekly Monthly Maintenance scheduleTechnical data Technical DataApproved accessories Type Cutting attachment guard, Art. no Your Warranty Rights and Obligations Federal Emission Control Warranty StatementPoly Trim Clic 35-50 NM 095-.130Page Mm 9,0 m Mm 7,5 m Mm 6,0 m 15 cm 10 m 10 cm 15 cm Clic 1088930-95 ´z*x¶5¢¨ ´z*x¶5¢¨