Jonsered FC 2145S manual Fitting other guards and cutting attachments, Standard harness

Page 16

ASSEMBLY

Fitting other guards and cutting attachments

Fit the trimmer guard/combination guard (A) intended for use with the trimmer head/plastic blades. Hang the trimmer guard/combination guard (A) on the two hooks on the plate holder (M). Bend the guard around the shaft and tighten it with the bolt (L) on the opposite side of the shaft. Use the locking pin (C). Place the locking pin in the groove on the screw head and tighten. See diagram.

H

P

BA

ML

•Fit the drive disc (B) on the output shaft.

•Centre the metal cup (P) on the drive disc’s blade guide.

•Turn the blade shaft until one of the holes in the drive disc aligns with the corresponding hole in the gear housing.

•Insert the locking pin (C) in the hole to lock the shaft.

L

M C

A

•Screw on the trimmer head/plastic blades (H) in the opposite direction to the direction of rotation.

•To dismantle, follow the instructions in the reverse order.

Adjusting the harness and clearing saw

WARNING! When using a clearing saw it

!must always be hooked securely to the harness. Otherwise you will be unable to control the clearing saw safely and this can result in injury to yourself or others. Never use a harness with a defective quick release.

Standard harness

Safety release

At the front is an easily accessible, quick release. Use this if the engine catches fire or in any other emergency situation that requires you to free yourself from the machine and harness.

Spreading the load on your shoulders

A well-adjusted harness and machine makes work much easier. Adjust the harness for the best working position. Tension the side straps so that the weight is evenly distributed across both shoulders.

Correct height

1Forestry clearing

The machine should be supported in a harness when forestry clearing so that the cutting equipment is angled slightly forwards in relation to the ground. Adjust the height using the strap on the harness for the support hook.

16 – English

Page 15 Page 17
Image 16
Page 15 Page 17
Contents Operator’s manual EPA KEY to Symbols SymbolsContents Introduction Dear customerWhat is WHAT? What is what on the clearing saw? BCWhat is what on the clearing saw? FC 2145, FC 2145 S General Safety Precautions Personal protective equipmentStop switch Machine′s safety equipmentThrottle lock Cutting attachment guard Vibration damping systemQuick release MufflerLocking nut Locking screwCutting equipment Cutting equipmentSharpening grass cutters and grass blades Sharpening the saw blade Trimmer headAssembly Assembling the handlebar and throttleTransport position, handlebar FC 2145, FC 2145 SFitting blades and trimmer heads Fitting the blade guard and saw blade Fitting the trimmer guard and trimmer head Trimmy SIIFitting other guards and cutting attachments Adjusting the harness and clearing sawStandard harness Adjusting the harness Vector harnessCorrect balance Grass clearingFuel Handling Fuel safetyFuel Fueling MixingStarting and Stopping Check before startingStarting and stopping Cold engineStarting StoppingBasic safety rules Working TechniquesGeneral working instructions ABC of clearingForestry clearing using a saw blade Working methodsGrass clearing using a grass blade Brush cutting with a saw bladeGrass trimming with a trimmer head TrimmingMaintenance CarburetorFine adjustment of the idle speed T Correctly adjusted carburetorAdjusting the start throttle speed BC High speed jet HCooling system MufflerAir filter Cleaning the air filter Bevel gearDrive shaft Spark plugTemperature 0C 32F or colder Winter useMaintenance schedule Maintenance Daily Weekly MonthlyTechnical Data Technical dataApproved accessories Type Cutting attachment guard, Art. no Federal Emission Control Warranty Statement Your Warranty Rights and ObligationsPoly Trim 095-.130 Clic 35-50 NMPage Mm 9,0 m Mm 7,5 m Mm 6,0 m 15 cm 10 m 10 cm 15 cm Clic 1088930-95 ´z*x¶5¢¨ ´z*x¶5¢¨
Top Page Image Contents