Jonsered FC 2145S manual Bevel gear, Drive shaft, Spark plug, Cleaning the air filter

Page 29

MAINTENANCE

Cleaning the air filter

Remove the air filter cover and take out the filter. Wash it clean in warm, soapy water.

An oiled foam plastic filter (available as an accessory) must be used if the machine is operated in extremely dusty conditions. See instructions under the heading Oiling the air filter.

Oiling the air filter

Always use special filter oil. Filter oil contains a solvent to make it spread evenly through the filter. You should therefore avoid skin contact.

Put the filter in a plastic bag and pour the filter oil over it. Knead the plastic bag to distribute the oil. Squeeze the excess oil out of the filter inside the plastic bag and pour off the excess before fitting the filter to the machine. Never use common engine oil. This would drain through the filter quite quickly and collect in the bottom.

An air filter that has been in use for a long time cannot be cleaned completely. The filter must therefore be replaced with a new one at regular intervals. A damaged air filter must always be replaced.

Bevel gear

The bevel gear is filled with the right amount of grease at the factory. However, before using the machine you should check that the bevel gear is filled 3/4 full with grease. Use JONSERED special grease.

The grease in the bevel gear does not normally need to be changed except if repairs are carried out.

Drive shaft

The drive shaft must be greased every three months during full-time use. Contact your dealer if you are uncertain about the procedure.

Spark plug

The spark plug condition is influenced by:

Incorrect carburetor adjustment.

An incorrect fuel mixture (too much or incorrect type of oil).

A dirty air filter.

These factors cause deposits on the spark plug electrodes, which may result in operating problems and starting difficulties.

If the machine is low on power, difficult to start or runs poorly at idle speed: always check the spark plug first before taking any further action. If the spark plug is dirty, clean it and check that the electrode gap is 0.5 mm (0,020"). The spark plug should be replaced after about a month in operation or earlier if necessary.

CAUTION! Always use the recommended spark plug type! Use of the wrong spark plug can damage the piston/cylinder. Check that the spark plug is fitted with a suppressor.

English – 29

Image 29
Contents Operator’s manual EPA Symbols KEY to SymbolsContents Dear customer IntroductionWhat is what on the clearing saw? BC What is WHAT?What is what on the clearing saw? FC 2145, FC 2145 S Personal protective equipment General Safety PrecautionsThrottle lock Machine′s safety equipmentStop switch Vibration damping system Cutting attachment guardQuick release MufflerLocking screw Locking nutSharpening grass cutters and grass blades Cutting equipmentCutting equipment Trimmer head Sharpening the saw bladeAssembling the handlebar and throttle AssemblyTransport position, handlebar FC 2145, FC 2145 SFitting blades and trimmer heads Fitting the trimmer guard and trimmer head Trimmy SII Fitting the blade guard and saw bladeStandard harness Adjusting the harness and clearing sawFitting other guards and cutting attachments Vector harness Adjusting the harnessCorrect balance Grass clearingFuel Fuel safetyFuel Handling Mixing FuelingCheck before starting Starting and StoppingStarting and stopping Cold engineStopping StartingWorking Techniques Basic safety rulesGeneral working instructions ABC of clearingWorking methods Forestry clearing using a saw bladeBrush cutting with a saw blade Grass clearing using a grass bladeTrimming Grass trimming with a trimmer headCarburetor MaintenanceCorrectly adjusted carburetor Fine adjustment of the idle speed TAdjusting the start throttle speed BC High speed jet HAir filter MufflerCooling system Bevel gear Cleaning the air filterDrive shaft Spark plugWinter use Temperature 0C 32F or colderMaintenance Daily Weekly Monthly Maintenance scheduleTechnical data Technical DataApproved accessories Type Cutting attachment guard, Art. no Your Warranty Rights and Obligations Federal Emission Control Warranty StatementPoly Trim Clic 35-50 NM 095-.130Page Mm 9,0 m Mm 7,5 m Mm 6,0 m 15 cm 10 m 10 cm 15 cm Clic 1088930-95 ´z*x¶5¢¨ ´z*x¶5¢¨