Marantz SR-18EX manual Do not Remove Cover or Back, No USER-SERVICEABLE Parts Inside

Page 5

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,

DO NOT REMOVE COVER (OR BACK)

NO USER-SERVICEABLE PARTS INSIDE

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL

The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of suffi-cient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

WARNING

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK,

DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.

CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE

BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.

ATTENTION: POUR ÉVITER LES CHOCS ÉLECTRIQUES,

INTRODUIRE LA LAME LA PLUS LARGE DE LA FICHE DANS LA

BORNE CORRESPONDANTE DE LA PRISE ET POUSSER

JUSQU’AU FOND.

NOTE TO CATV SYSTEM INSTALLER:

This reminder is provided to call the CATV (Cable-TV) system installer’s attention to Article 820-40 of the NEC, that provides guidelines for proper grounding and, in particular, specified that the cable ground shall be connected to the grounding system of the building, as close to the point of cable entry as practical.

NOTE:

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communica- tions. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by tuning the equipment off and on, the user is encouraged to try to

correct the interference by one or more of the following measures:

-Reorient or relocate the receiving antenna.

-Increase the separation between the equipment and receiver.

-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

-Consult the dealer or an experienced radio/TV technician for help.

NOTE:

Changes or modifications may cause this unit to fail to comply with Part 15 of the FCC Rules and may void the user’s authority to operate the equipment.

Image 5
Contents Model SR-18EX User Guide AUX Input Video Video OUTVideo Audio OUT OUT OUT OUT OUT Digital Audio Video S-VIDEO Video CameraCenter Speaker CD Player Subwoofer Speaker System AmplifierOutput DigitalOther Connections Power AmprifirOther Multi Channel Processor MA700Do not Remove Cover or Back No USER-SERVICEABLE Parts InsideRefer Servicing to Qualified Service Personnel AC Polarized Plug Read Before Operating EquipmentNEC Section @2@0 I !0 O !1!2!3 Table of Contents Description IntroductionFeatures Button Front Panel Features see8PRESET Button Display Rear Panel Connections AC Inlet AC Outlets⁄2TEN Keypad Remote Control Unit RC-18SR⁄1VOLUME UP + and Down No Good Operation of Remote Control UnitOn Screen Display Menu System SetupSpeakers Setup Speakers Setup and Levels SetupSpkrs Setup 1/2 Speaker Size OSD Menu SystemLevels Setup 1/2 Test Tone Generator Spkrs Setup 2/2 Speaker DistanceLevels Setup 2/2 Bass Peak Level Limit L U M ES T E M S E T U P 2 System Setup 2/2 Assignable Digital InputA L O G P E A L O GGeneral Information On Screen Display InfomationListening to the Tuner Basic OperationPlayback Operation Station Name PresetDirect Frequency Call Normal PlaybackOther Functions Setting the Sleep Timer only Remote Control UnitMulti Room Selector TV Auto ON/OFF FunctionFunction and Operation Operation⁄4CLEAR Function⁄3MEMO ⁄7MUTE Liquid Crystal Display LCD Window⁄8GUIDE ⁄9LIGHTINGRC-18SR Basic Operation Programming the Direct mode buttons mHow to re-write the Direct function button names How to re-write the Status nameHow to clear erase the memorized codes Any re-written names Erasing the memory assigned to a particular buttonAdvanced Programming Techniques Macro modeErasing the memory assigned to a Direct buttons Complete erasureProgramming a macro under a function selector key Would not normally be included in a macro sequence, and areTherefore not available for inclusion in a macro Clone mode Using the macro functions you have programmedRC-18SR RC2000MKII ALL OK Table of cloning relationsVER Other FunctionsDirect Command Functions Listing DVD MODE1 Angl Tape Mode TP-BSubt MenuPIP2/REC VCR1 ModeRest SLPAUX VCD/PHI Mode ProgRest OSD VCD/PHI PBCSurround Modes DSP THX EXDigital Stereo Surround Mode CH status 5ch StereoDigital Mono 6ch InputSymptom Cause Remedy TroubleshootingMemory backup Error MessagesHOW to Reset the Unit General MalfunctionFM Tuner Section Technical SpecificationsAM Tuner Section Audio SectionIs a registered trademark