| SVENSKA | NEDERLANDS |
|
|
|
Setting items | Setting details |
|
Distance |
|
(Continued) | • The speakers that can be selected differ depending on the “Amp Assign” |
| |
| (vpage 61) and “Speaker Config.” (vpage 61) settings. |
| • Default settings : |
| Front L / Front R / Center / Subwoofer / F.Height L / F.Height R : |
| 12.0 ft (3.6 m) |
| Surround L / Surround R / S.Back L / S.Back R : 10.0 ft (3.0 m) |
| • Set the difference in the distance between the speakers to less than 20 |
| ft (6.0 m). |
NOTE
Speakerssetto“None”in“SpeakerConfig.” (vpage61)arenotdisplayed.
Default : The “Distance” settings are returned to the default settings.
•Yes : Reset to the defaults.
•No : Do not reset to the defaults.
| When you select “Default” and press ENTER, the “Default Setting?” |
| prompt is displayed. Select either “Yes” or “No”, and press ENTER. |
Channel Level | Test Tone Start : Output test tone. |
Set the volume of the test | • Front L / F.Height L / Center / F.Height R / Front R / Surround R / |
tone to be the same when it S.Back Rz / S.Back Lz / Surround L / Subwoofer : Select the speaker. is output from each speaker. zz When the “Speaker Config.” – “S.Back” setting (vpage 62) is set to
“1spkr”, “S.Back” is displayed.
•–12.0dB – +12.0dB (0.0dB) : Adjust the volume.
•When o is pressed while the subwoofer volume is set to
•When “Channel Level” is adjusted, the adjusted values are set for all the surround modes. To adjust the channel level separately for the different surround modes, use the operation see page 43.
•When you press TEST TONE on the remote control unit, you can enter this setting item immediately.
NOTE
•Speakers set to “None” in the “Speaker Config.” (vpage 61) settings are not displayed.
•When a headphones jack is inserted in the PHONES jack of this unit, the “Channel Level” is not displayed.
Default : The “Channel Level” settings are returned to the default settings.
•Yes : Reset to the defaults.
•No : Do not reset to the defaults.
When you select “Default” and press ENTER, the “Default Setting?” prompt is displayed. Select either “Yes” or “No”, and press ENTER.
ESPAÑOL | ITALIANO | FRANÇAIS | DEUTSCH | ENGLISH | |
|
|
|
|
| Manual Setup |
|
|
|
|
|
|
Setting items |
|
|
| Setting details |
|
|
|
|
| ||
Crossover Frequency |
| Crossover : Set the crossover frequency. |
| ||
Set the maximum frequency | • 40Hz / 60Hz / 80Hz / 90Hz / 100Hz / 110Hz / 120Hz / 150Hz / 200Hz / | ||||
of the bass signal output | 250Hz |
|
|
|
from each channel to | Advanced : Specify crossover frequency for each speaker. | |||||
the subwoofer. Set the | ||||||
• Front / Center / Surround | / S.Back | / F.Height : Select the speaker. | ||||
Crossover Frequency to | ||||||
• 40Hz | / 60Hz | / 80Hz / 90Hz | / 100Hz | / 110Hz / 120Hz / 150Hz / 200Hz / | ||
suit the bass reproduction |
capability of the speaker | 250Hz : Set the crossover frequency. |
| |
being used. |
|
•“Crossover Frequency” can be set when the “Bass Setting” – “Subwoofer Mode” (vpage 62) setting is “LFE+Main”, or when you have a speaker that is set to “Small”.
•Always set the crossover frequency to “80Hz”. When using small speakers, however, we recommend setting the crossover frequency to a higher frequency.
•For speakers set to “Small”, sound below the crossover frequency is cut from the sound output. The cut bass sound is output from the subwoofer or front speakers.
•The speakers that can be set when “Advanced” is selected differ depending on to the “Subwoofer Mode” setting (vpage 62).
•When “LFE” is selected, speakers set to “Small” at “Speaker Config.” can be set. If the speakers are set to “Large”, “Full Band” is displayed and the setting cannot be made.
•If set to “LFE+Main”, this setting can be made regardless of the speaker size.
Simple version
Basic version
Advanced version
Information
Remote control operation | Move the cursor | Confirm the setting | Return to previous menu | 63 |
buttons | (Up/Down/Left/Right) |
| ||
|
|
|