Marantz SR6005 Preparation, Speaker Detection, When performing Audyssey Auto Setup over again

SVENSKA NEDERLANDS ESPAÑOL ITALIANO FRANÇAIS DEUTSCH ENGLISH

Set up speakers (Audyssey® Auto Setup)

STEP 1

Preparation

4 Connect the setup microphone to the SETUP MIC jack of this unit.

STEP 2

Speaker Detection

•In STEP 2, you will perform measurements at the main listening position.

•This step automatically checks the speaker configuration and speaker size, and calculates the channel level, distance, and crossover frequency. It also corrects distortion in the listening area.

NOTE

If “Caution” is displayed:

Go to “Error messages” (vpage 11), check any related items, and perform the necessary procedures.

If the problem is resolved, return and restart

STEP 3

Measurement

•In STEP 2, you will perform measurements at multiple positions (two to six positions) other than the main listening position.

•You can achieve a more effective correction of distortion within the listening area by performing measurements at multiple positions.

Simple version

Basic

When the setup microphone is connected, the following screen is displayed.

6 Select “Measure” and then press

ENTER.

When measuring begins, a test tone is output from each speaker.

• Measurement requires several minutes.

7 The detected speakers are displayed.

“Audyssey Auto Setup”.

When performing Audyssey Auto Setup over again

Press uito select “Retry”, and then press ENTER.

When measuring has stopped

Press RETURN, to the “Cancel Auto Setup?”

9 Move the setup microphone to position 2, use ui to select “Measure”, and then press ENTER.

The measurement of the second position starts. Measurements can be made in up to six positions.

AUTO SETUP
AUDYSSEY AUTO SETUP	MultEQ

version

AUTO SETUP
AUDYSSEY AUTO SETUP		MultEQ	AUTO SETUP
STEP1 Preparation		[1/6]	AUDYSSEY AUTO SETUP				MultEQ
Connect the speakers			STEP2 Spkr Detect Check					[2/6]
and place them accord-
			Front		Yes
ing to the recommenda-
			Center		Yes
tions in the manual.
			Subwoofer		Yes
Set the following
			Surround		Yes
items if necessary.
			S.Back		2spkrs
Amp Assign
Channel Select
Auto Setup Start			Retry
ENTER	Enter	RETURN Cancel	Next	Measurement
Start Auto Setup					ENTER	Enter	RETURN Cancel
This screen provides	the	method for setting	Go to Step 3 (Measurement) after speaker check
up 7.1-channel playback using surround back			NOTE
speakers. For the method of setting up speakers
			If a connected speaker is not displayed, the
other than the 7.1-channel system, select “Amp
Assign” and perform step 3 and 4 of “Set up			speaker may not be connected correctly. Check
“Amp Assign”” (vpage 39).			the speaker connection.
If unused channels are set with “Channel			Use	ui to		select		“Next	1
Select”, measuring time can be shortened. For
setting, perform steps 5 to 9 of “Set up “Channel			8 Measurement” and then press ENTER.
Select”” (vpage 39).

5 Use uito select “Auto Setup Start” and then press ENTER.

prompt is displayed.

Press o to select “Yes”, then press ENTER.

Setting up the speakers again

Repeat the operation from step 4 of STEP1 Preparation .

STEP3 Measurement	[3/6]
Please place the mic-
rophone at ear height
at 2nd listening
position.
Measure
Next Calculation
ENTER Enter		RETURN Cancel

Start next measurement. Test Tone will start

If you want to omit measurements from the next position onward, select “Next 1 Calculation”.

(Go to STEP4 Calculation )

10Repeatto 6. step 9, measuring positions 3

When measurement of position 6 is completed, a “Measurements finished.” message is displayed.

AUTO SETUP
AUDYSSEY AUTO SETUP	MultEQ

STEP3 Measurement	[3/6]
Measurements finished.
Retry
Next Calculation
ENTER Enter		RETURN Cancel
Proceed to Step 4 (Analyze)

Advanced version

Information

Remote control operation	Move the cursor	Confirm the setting	Return to previous menu	9
buttons	(Up/Down/Left/Right)