Briggs & Stratton Achieve a Perfect Straight Take: Operation Guide for Zero Turn Mowers

Page 20

Operation

Operation

ZERO TURN

DRIVING PRACTICE

The lever controls of the Zero Turn rider are responsive, and learning to gain a smooth and efficient control of the rider’s forward, reverse, and turning movements will take some practice.

Spending some time going through the maneuvers shown and becoming familiar with how the unit accelerates, travels, and steers — before you begin mowing —is absolutely essential to getting the most out of the Zero Turn rider.

Locate a smooth, flat area of your lawn — one with plenty of room to maneuver. (Clear the area of objects, people and animals before you begin.) Operate the unit at mid-throttle during this practice session (ALWAYS operate at full throttle when mowing), and turn slowly to prevent tire slippage and damage to your lawn.

We suggest you begin with the Smooth Travel procedure to the right, and then advance through the forward, reverse, and turning maneuvers.

You must release the parking brake prior to moving the control levers inward.

Smooth Travel

The lever controls of the Zero Turn rider are

responsive.

The BEST method of handling the ground speed control levers is in three steps — as shown in Figure 3.

FIRST place your hands onto the levers as shown.

SECOND, to go forward gradually push the levers forward with your palms.

THIRD, to speed up move the levers farther forward. To slow down smoothly, slowly move the levers toward neutral.

Figure 3. Move Control

Levers Gradually

BASIC DRIVING

Forward Travel Practice

Gradually move both ground speed control levers — evenly FORWARD from neutral. Slow down and repeat.

NOTE: Straight forward travel takes practice. If necessary, top speed can be balance-adjusted — see the Speed Balancing Adjustment in the Adjustments section near the back of this manual.

Forward

Travel

Reverse Travel Practice

LOOK DOWN & BEHIND, then gradually move both ground speed control levers evenly BACK from neutral. Slow down and repeat.

NOTE: Practice backing up for several minutes before attempting to do so near objects. The rider turns sharply in reverse as well as forward, and backing up straight takes practice.

Reverse

Travel

Figure 4. Forward Travel

Figure 5. Reverse Travel

18

www.ferrisindustries.com

Image 20
Contents Model Number Briggs & Stratton Power Products Group, LLC 5100806Description Date Purchased Table of Contents Operating Safety Slope Operation Roll Bar Use Fuel and Maintenance Preparation OperationTraining Slope Operation Towed Equipment RIDE-ON UnitsChildren EmissionsService and Maintenance Ignition System Gasoline ModelsRoll BAR Instructions Operational WarningsInspection and Maintenance of the Roll BAR Seat Belt Identification Numbers Identification TagSafety Decals Operational Safety Checks Safety Interlock SystemNorth American Safety Icons Seat Adjustment Lever Ignition SwitchControl Functions Ground Speed LeversPTO Power Take Off Switch Hour Meter / Maintenance ReminderWater Temperature Gauge Throttle ControlGeneral Operating Safety Checks Before StartingPushing the Rider by Hand Starting the EngineStopping the Rider Zero Turn Driving Practice Smooth TravelForward Travel Practice Reverse Travel PracticePractice Turning Around a Corner Practice Turning In Place Executing an End-Of-Row Zero TurnExecuting Turns TurningMowing Mowing RecommendationsHeight of Grass Tall Grass Requires Incremental CuttingWhen and How Often to Mow Mowing MethodsMowing Patterns Proper Broadcast MowingAttaching a Trailer Proper MulchingRaise & Lower the Roll BAR To lower the roll barTo raise the roll bar Keep roll bar in the raised position and use seat beltStorage Starting After Long Term StorageTemporary Storage 30 Days Or Less Long Term Storage Longer Than 30 DaysSafety Items Rider MaintenanceEngine Maintenance Before Every Spring Each 100 250 Fall Use HoursCheck Tire Pressures Checking / Adding FuelFuel Filter Change OIL & FilterChange Interval Every 500 Hours Filter Part Number Check Hydraulic OIL LevelHydraulic OIL Filter Change Pressurized System Change Engine Coolant Clean Radiator & ScreenCheck Engine Coolant Level Oil LubricationGrease ANTI-SCALP Deck Casters Battery MaintenanceCleaning the Battery and Cables Servicing the Mower Blades Removing the BladeRegular Maintenance Troubleshooting Warning Troubleshooting the RiderTroubleshooting the Mower Rider TroubleshootingTroubleshooting Common Cutting Problems StreakingGround Speed Control Lever Adjustment Seat AdjustmentSeat Adjustment Suspension Seat To Reduce the Speed of the Faster Wheel Speed Balancing AdjustmentNeutral Adjustment RETURN-TO-NEUTRAL Adjustment Parking Brake AdjustmentSuspension Adjustment To adjust the spring pre-loadPTO Clutch Adjustment Blade Brake CheckTo adjust pedal position Cutting Height AdjustmentFoot Pedal Adjustment Deck Lift ROD Timing Adjustment Outer Rod . Adjust the Inner & Outer Lift RodsInner Rod Outer RodDeck Leveling Adjustment Deck Lift SpringHydraulic Pump Drive Belt Replacement Mower Belt Replacement Mower PTO Belt 72 Mower Deck Nut Stationary Idler PulleyBattery Service Checking Battery VoltageCharging a Completely Discharged Battery Jump Starting With Auxiliary Booster BatteryThis HOOK-UP for Negative Ground Vehicles Make Certain Vehicles do not TouchDimensions EngineChassis TransmissionsFerris Limited Warranty Mower Deck Belts and BladesTractor

5900612, 5900613, 5900611, 5900716, 5900752 specifications

Briggs & Stratton is a leading manufacturer of small engines, known for their reliability and performance in a variety of applications. Among their extensive range of products, the model numbers 5900752, 5901184, 5900753, 5900611, and 5900613 represent a collection of essential components designed to enhance engine efficiency and user experience.

The Briggs & Stratton 5900752 is recognized for its high-quality air filter. This filter is engineered to trap dust and dirt effectively, ensuring that only clean air enters the engine. A clean air intake is crucial for optimal performance and longevity of the engine, as it prevents wear and tear on internal components. Its design allows for easy installation and maintenance, making it user-friendly for homeowners and professionals alike.

The 5901184 is a fuel tank assembly designed for enhanced durability and a consistent fuel supply. This component is vital for maintaining stable engine performance, minimizing fuel leakage, and ensuring the integrity of the engine system. The material used in its construction is resistant to corrosion, which is critical for longevity, especially in outdoor equipment exposed to various environmental conditions.

The 5900753 represents a high-performance carburetor that plays a significant role in the mixture of air and fuel. Its precision-engineered design allows for efficient combustion, resulting in robust engine performance. This carburetor is built to handle fluctuations in load, ensuring that the engine runs smoothly under different operating conditions.

The Briggs & Stratton 5900611 and 5900613 series are vital components known for their ignition systems. These components contribute to reliable spark generation, which is essential for engine starting and operation. The enhanced ignition efficiency not only boosts engine starts but also promotes fuel efficiency and reduces emissions, aligning with the growing demand for environmentally conscious products.

Overall, the features and technologies present in the Briggs & Stratton 5900752, 5901184, 5900753, 5900611, and 5900613 highlight the company’s commitment to quality, performance, and user-centered design. With a focus on reliability and ease of use, these components are engineered to meet the needs of various applications, from residential lawn care to commercial landscaping. As part of Briggs & Stratton's extensive catalog, these components are essential for maintaining optimal engine performance and ensuring a seamless user experience in the field.