Briggs & Stratton 5900753, 5901186, 5901183, 5901184, 5900717, 5900718, 5900736 manual Slope Operation

Page 5

Operator Safety

Slope Operation

Operation on slopes can be dangerous. Using the unit on a slope that is too steep where you do not have adequate wheel traction (and control) can cause sliding, loss of steering, control, and possible rollover. You should not operate on a slope greater than a 5.4 foot rise over a 20 foot length (15 degrees).

Always mow across slopes, not up and down (to maintain traction on the wheels) and avoid sudden turns or rapid speed changes. Reduce speed and use extreme caution on ALL slopes.

Also, note that the surface condition you are on can greatly impact your ability to safely operate this machine. Operating on wet or slippery slopes can cause sliding and loss of steering and control. Do not operate on slopes that are slippery, wet, or have soft soil conditions.

If you feel unsure about operating the unit on a slope, don’t do it.

It’s not worth the risk.

Thrown Objects

This unit has spinning mower blades. These blades can pick up and throw debris that could seriously injure a bystander. Be sure to clean up the area to be mowed and remove objects that could be thrown by the blade BEFORE you start mowing.

Do not operate this unit without the entire grass catcher or discharge guard (deflector) in place.

Also, do not allow anyone in the area while the unit is running! If someone does enter the area, shut the unit off immediately until they leave.

Moving Parts

This equipment has many moving parts that can injure you or someone else. However, if you stay in the operator zone (stay seated in the seat), and follow the safety rules in this operator’s manual, the unit is safe to operate.

The mower deck has spinning mower blades that can amputate hands and feet. Do not allow anyone near the unit while it is running! Keep safety devices (guards, shields, and switches) in place and working.

To help you, the operator, use this equipment safely, it is equipped with an operator-present safety system. Do NOT attempt to alter or bypass the system. See your dealer immediately if the system does not pass all the safety interlock system tests found in this manual.

Safety

3

Image 5
Contents Model Number Briggs & Stratton Power Products Group, LLC 5100806Description Date Purchased Table of Contents Operating Safety Slope Operation Roll Bar Use Fuel and Maintenance Preparation OperationTraining Towed Equipment RIDE-ON Units Slope OperationChildren EmissionsIgnition System Gasoline Models Service and MaintenanceOperational Warnings Roll BAR InstructionsInspection and Maintenance of the Roll BAR Seat Belt Identification Tag Identification NumbersSafety Decals Operational Safety Checks Safety Interlock SystemNorth American Safety Icons Ignition Switch Seat Adjustment LeverControl Functions Ground Speed LeversHour Meter / Maintenance Reminder PTO Power Take Off SwitchWater Temperature Gauge Throttle ControlChecks Before Starting General Operating SafetyPushing the Rider by Hand Starting the EngineStopping the Rider Smooth Travel Zero Turn Driving PracticeForward Travel Practice Reverse Travel PracticeExecuting an End-Of-Row Zero Turn Practice Turning Around a Corner Practice Turning In PlaceExecuting Turns TurningMowing Recommendations MowingHeight of Grass Tall Grass Requires Incremental CuttingMowing Methods When and How Often to MowMowing Patterns Proper Broadcast MowingProper Mulching Attaching a TrailerTo lower the roll bar Raise & Lower the Roll BARTo raise the roll bar Keep roll bar in the raised position and use seat beltStarting After Long Term Storage StorageTemporary Storage 30 Days Or Less Long Term Storage Longer Than 30 DaysRider Maintenance Safety ItemsEngine Maintenance Before Every Spring Each 100 250 Fall Use HoursChecking / Adding Fuel Check Tire PressuresFuel Filter Change OIL & FilterChange Interval Every 500 Hours Filter Part Number Check Hydraulic OIL LevelHydraulic OIL Filter Change Pressurized System Change Engine Coolant Clean Radiator & ScreenCheck Engine Coolant Level Oil LubricationGrease ANTI-SCALP Deck Casters Battery MaintenanceCleaning the Battery and Cables Removing the Blade Servicing the Mower BladesRegular Maintenance Troubleshooting the Rider Troubleshooting WarningRider Troubleshooting Troubleshooting the MowerStreaking Troubleshooting Common Cutting ProblemsGround Speed Control Lever Adjustment Seat AdjustmentSeat Adjustment Suspension Seat To Reduce the Speed of the Faster Wheel Speed Balancing AdjustmentNeutral Adjustment Parking Brake Adjustment RETURN-TO-NEUTRAL AdjustmentTo adjust the spring pre-load Suspension AdjustmentBlade Brake Check PTO Clutch AdjustmentTo adjust pedal position Cutting Height AdjustmentFoot Pedal Adjustment Outer Rod . Adjust the Inner & Outer Lift Rods Deck Lift ROD Timing AdjustmentInner Rod Outer RodDeck Lift Spring Deck Leveling AdjustmentHydraulic Pump Drive Belt Replacement Mower PTO Belt 72 Mower Deck Nut Stationary Idler Pulley Mower Belt ReplacementChecking Battery Voltage Battery ServiceCharging a Completely Discharged Battery Jump Starting With Auxiliary Booster BatteryMake Certain Vehicles do not Touch This HOOK-UP for Negative Ground VehiclesEngine DimensionsChassis TransmissionsFerris Limited Warranty Mower Deck Belts and BladesTractor

5900612, 5900613, 5900611, 5900716, 5900752 specifications

Briggs & Stratton is a leading manufacturer of small engines, known for their reliability and performance in a variety of applications. Among their extensive range of products, the model numbers 5900752, 5901184, 5900753, 5900611, and 5900613 represent a collection of essential components designed to enhance engine efficiency and user experience.

The Briggs & Stratton 5900752 is recognized for its high-quality air filter. This filter is engineered to trap dust and dirt effectively, ensuring that only clean air enters the engine. A clean air intake is crucial for optimal performance and longevity of the engine, as it prevents wear and tear on internal components. Its design allows for easy installation and maintenance, making it user-friendly for homeowners and professionals alike.

The 5901184 is a fuel tank assembly designed for enhanced durability and a consistent fuel supply. This component is vital for maintaining stable engine performance, minimizing fuel leakage, and ensuring the integrity of the engine system. The material used in its construction is resistant to corrosion, which is critical for longevity, especially in outdoor equipment exposed to various environmental conditions.

The 5900753 represents a high-performance carburetor that plays a significant role in the mixture of air and fuel. Its precision-engineered design allows for efficient combustion, resulting in robust engine performance. This carburetor is built to handle fluctuations in load, ensuring that the engine runs smoothly under different operating conditions.

The Briggs & Stratton 5900611 and 5900613 series are vital components known for their ignition systems. These components contribute to reliable spark generation, which is essential for engine starting and operation. The enhanced ignition efficiency not only boosts engine starts but also promotes fuel efficiency and reduces emissions, aligning with the growing demand for environmentally conscious products.

Overall, the features and technologies present in the Briggs & Stratton 5900752, 5901184, 5900753, 5900611, and 5900613 highlight the company’s commitment to quality, performance, and user-centered design. With a focus on reliability and ease of use, these components are engineered to meet the needs of various applications, from residential lawn care to commercial landscaping. As part of Briggs & Stratton's extensive catalog, these components are essential for maintaining optimal engine performance and ensuring a seamless user experience in the field.