Briggs & Stratton 5900611, 5901186, 5901183, 5901184 Deck Leveling Adjustment, Deck Lift Spring

Page 45

Troubleshooting, Adjustment & Service

DECK LEVELING ADJUSTMENT

NOTE: Before adjusting the deck level, the deck lift rod timing must be checked and/or adjusted.

1.Park machine on a flat, level surface. Disengage the PTO, stop the engine and engage the parking brake. Rear tires must be inflated to 15 psi (1,03 bar); front tires to 25 psi (1,72 bar).

2.Lock the deck lift pedal in the 5” (12,7cm) position. Place the deck height adjustment pin in the 4" position and lower deck the lift pedal until the arm contacts the pin.

3.Place 2 x 4 blocks under each corner of the mower deck with the 3-1/2” sides being vertical. Place a 1/4” (0,64cm) thick spacer on top of the rear 2 x 4 blocks. See Figure 41.

6.Adjust the front eyebolts until the chains are tight and the deck is still resting on the 2 x 4’s. Tighten jam nuts. See Figure 42.

7.Loosen the nuts and allow the rear of the deck to rest on the 2 x 4’s and 1/4” spacers. Slide the chains down in the slots until the chains are tight and tighten the nuts. See Figure 42.

8.Remove all 2 x 4 blocks and spacers from under the mower deck.

Figure 41.

2 x 4 Locations

 

Adjust Here

 

Adjust Here

Figure 42. Deck Level & Spring Length Adjustment

DECK LIFT SPRING

The deck lift springs (A, Figure 43) are factory set to provide optimal lifting performance.

Although it is fastened with a multi-position anchor, this is NOT AN ADJUSTMENT POINT.

DO NOT attempt to adjust the spring length or lifting performance will be compromised.

A

Troubleshooting

 

Figure 43. Deck Lift Spring Location

 

A. Deck Lift Spring

 

43

Page 44 Page 46
Image 45
Page 44 Page 46
Contents Briggs & Stratton Power Products Group, LLC 5100806 DescriptionModel Number Date Purchased Table of Contents Operating Safety Slope Operation Roll Bar Use Fuel and Maintenance Operation TrainingPreparation Towed Equipment RIDE-ON Units Slope OperationChildren EmissionsIgnition System Gasoline Models Service and MaintenanceOperational Warnings Roll BAR InstructionsInspection and Maintenance of the Roll BAR Seat Belt Identification Tag Identification NumbersSafety Decals Safety Interlock System North American Safety IconsOperational Safety Checks Ignition Switch Seat Adjustment LeverControl Functions Ground Speed LeversHour Meter / Maintenance Reminder PTO Power Take Off SwitchWater Temperature Gauge Throttle ControlChecks Before Starting General Operating SafetyStarting the Engine Stopping the RiderPushing the Rider by Hand Smooth Travel Zero Turn Driving PracticeForward Travel Practice Reverse Travel PracticeExecuting an End-Of-Row Zero Turn Practice Turning Around a Corner Practice Turning In PlaceExecuting Turns TurningMowing Recommendations MowingHeight of Grass Tall Grass Requires Incremental CuttingMowing Methods When and How Often to MowMowing Patterns Proper Broadcast MowingProper Mulching Attaching a TrailerTo lower the roll bar Raise & Lower the Roll BARTo raise the roll bar Keep roll bar in the raised position and use seat beltStarting After Long Term Storage StorageTemporary Storage 30 Days Or Less Long Term Storage Longer Than 30 DaysRider Maintenance Safety ItemsEngine Maintenance Before Every Spring Each 100 250 Fall Use HoursChecking / Adding Fuel Check Tire PressuresFuel Filter Change OIL & FilterCheck Hydraulic OIL Level Hydraulic OIL Filter ChangeChange Interval Every 500 Hours Filter Part Number Change Engine Coolant Clean Radiator & Screen Check Engine Coolant LevelPressurized System Lubrication GreaseOil Battery Maintenance Cleaning the Battery and CablesANTI-SCALP Deck Casters Removing the Blade Servicing the Mower BladesRegular Maintenance Troubleshooting the Rider Troubleshooting WarningRider Troubleshooting Troubleshooting the MowerStreaking Troubleshooting Common Cutting ProblemsSeat Adjustment Seat Adjustment Suspension SeatGround Speed Control Lever Adjustment Speed Balancing Adjustment Neutral AdjustmentTo Reduce the Speed of the Faster Wheel Parking Brake Adjustment RETURN-TO-NEUTRAL AdjustmentTo adjust the spring pre-load Suspension AdjustmentBlade Brake Check PTO Clutch AdjustmentCutting Height Adjustment Foot Pedal AdjustmentTo adjust pedal position Outer Rod . Adjust the Inner & Outer Lift Rods Deck Lift ROD Timing AdjustmentInner Rod Outer RodDeck Lift Spring Deck Leveling AdjustmentHydraulic Pump Drive Belt Replacement Mower PTO Belt 72 Mower Deck Nut Stationary Idler Pulley Mower Belt ReplacementChecking Battery Voltage Battery ServiceCharging a Completely Discharged Battery Jump Starting With Auxiliary Booster BatteryMake Certain Vehicles do not Touch This HOOK-UP for Negative Ground VehiclesEngine DimensionsChassis TransmissionsFerris Limited Warranty Belts and Blades TractorMower Deck

5900612, 5900613, 5900611, 5900716, 5900752 specifications

Briggs & Stratton is a leading manufacturer of small engines, known for their reliability and performance in a variety of applications. Among their extensive range of products, the model numbers 5900752, 5901184, 5900753, 5900611, and 5900613 represent a collection of essential components designed to enhance engine efficiency and user experience.

The Briggs & Stratton 5900752 is recognized for its high-quality air filter. This filter is engineered to trap dust and dirt effectively, ensuring that only clean air enters the engine. A clean air intake is crucial for optimal performance and longevity of the engine, as it prevents wear and tear on internal components. Its design allows for easy installation and maintenance, making it user-friendly for homeowners and professionals alike.

The 5901184 is a fuel tank assembly designed for enhanced durability and a consistent fuel supply. This component is vital for maintaining stable engine performance, minimizing fuel leakage, and ensuring the integrity of the engine system. The material used in its construction is resistant to corrosion, which is critical for longevity, especially in outdoor equipment exposed to various environmental conditions.

The 5900753 represents a high-performance carburetor that plays a significant role in the mixture of air and fuel. Its precision-engineered design allows for efficient combustion, resulting in robust engine performance. This carburetor is built to handle fluctuations in load, ensuring that the engine runs smoothly under different operating conditions.

The Briggs & Stratton 5900611 and 5900613 series are vital components known for their ignition systems. These components contribute to reliable spark generation, which is essential for engine starting and operation. The enhanced ignition efficiency not only boosts engine starts but also promotes fuel efficiency and reduces emissions, aligning with the growing demand for environmentally conscious products.

Overall, the features and technologies present in the Briggs & Stratton 5900752, 5901184, 5900753, 5900611, and 5900613 highlight the company’s commitment to quality, performance, and user-centered design. With a focus on reliability and ease of use, these components are engineered to meet the needs of various applications, from residential lawn care to commercial landscaping. As part of Briggs & Stratton's extensive catalog, these components are essential for maintaining optimal engine performance and ensuring a seamless user experience in the field.
Top Page Image Contents