Briggs & Stratton 5900753, 5901186, 5901183 Check Hydraulic OIL Level, Hydraulic OIL Filter Change

Page 29

CHECK HYDRAULIC OIL LEVEL

NOTE: Do not open the hydraulic reservoir unless oil is being added.

1.Lift up the seat plate to gain access to the oil reservoir compartment.

2.Look at the hydraulic oil reservoir (A, Figure 13) and observe the oil level. When cold, the oil level should be approximately 1/2” (1,3cm) below the MAX. HOT OIL LEVEL line. The oil level should never be above the MAX. HOT OIL LEVEL line.

3.If necessary, remove the reservoir cap (B, Figure 13) and add either Mobil 1, 15W-50 synthetic oil or Castrol Syntec 5W-50 oil. DO NOT use conventional oils. Make sure area around the fill neck of the reservoir is free of dust, dirt, or other debris.

Regular Maintenance

B

A

Figure 13. Checking Hydraulic Oil Level

A.Hydraulic Oil Reservoir

B.Reservoir Cap

HYDRAULIC OIL FILTER CHANGE

Change Interval: Every 500 Hours

Filter Part Number: 5021357

NOTE: Removing the oil filter from the filter base will drain the oil reservoir. Have a suitable container ready to catch any spilled oil. Ferris recommends this be a dealer-only service item.

1.Locate the hydraulic oil filter (A, Figure 14) behind the oil reservoir.

2.Fill the new filter with oil. Lubricate the new filter seal with a few drops of oil.

3.Remove the oil filter and quickly thread the new filter onto the filter base until the gasket makes contact, then tighten 3/4 of a turn more.

4.Refill reservoir with fresh oil to replace any oil lost during filter change.

5.Raise the rear of the unit and secure with jackstands. Chock the front wheels to prevent the unit from rolling. Run the unit for several minutes to purge any air from the hydraulic system and check the hydraulic oil level.

IMPORTANT NOTE: Use caution after changing the filter; air in the hydraulic system may affect the responsiveness of the control levers. Repeat step 5 until the air is out of the system.

A

Figure 14. Hydraulic Oil Filter Location A. Oil Filter

Maintenance

27

Page 28 Page 30
Image 29
Page 28 Page 30
Contents Model Number Briggs & Stratton Power Products Group, LLC 5100806Description Date Purchased Table of Contents Operating Safety Slope Operation Roll Bar Use Fuel and Maintenance Preparation OperationTraining Towed Equipment RIDE-ON Units Slope OperationChildren EmissionsIgnition System Gasoline Models Service and MaintenanceOperational Warnings Roll BAR InstructionsInspection and Maintenance of the Roll BAR Seat Belt Identification Tag Identification NumbersSafety Decals Operational Safety Checks Safety Interlock SystemNorth American Safety Icons Ignition Switch Seat Adjustment LeverControl Functions Ground Speed LeversHour Meter / Maintenance Reminder PTO Power Take Off SwitchWater Temperature Gauge Throttle ControlChecks Before Starting General Operating SafetyPushing the Rider by Hand Starting the EngineStopping the Rider Smooth Travel Zero Turn Driving PracticeForward Travel Practice Reverse Travel PracticeExecuting an End-Of-Row Zero Turn Practice Turning Around a Corner Practice Turning In PlaceExecuting Turns TurningMowing Recommendations MowingHeight of Grass Tall Grass Requires Incremental CuttingMowing Methods When and How Often to MowMowing Patterns Proper Broadcast MowingProper Mulching Attaching a TrailerTo lower the roll bar Raise & Lower the Roll BARTo raise the roll bar Keep roll bar in the raised position and use seat beltStarting After Long Term Storage StorageTemporary Storage 30 Days Or Less Long Term Storage Longer Than 30 DaysRider Maintenance Safety ItemsEngine Maintenance Before Every Spring Each 100 250 Fall Use HoursChecking / Adding Fuel Check Tire PressuresFuel Filter Change OIL & FilterChange Interval Every 500 Hours Filter Part Number Check Hydraulic OIL LevelHydraulic OIL Filter Change Pressurized System Change Engine Coolant Clean Radiator & ScreenCheck Engine Coolant Level Oil LubricationGrease ANTI-SCALP Deck Casters Battery MaintenanceCleaning the Battery and Cables Removing the Blade Servicing the Mower BladesRegular Maintenance Troubleshooting the Rider Troubleshooting WarningRider Troubleshooting Troubleshooting the MowerStreaking Troubleshooting Common Cutting ProblemsGround Speed Control Lever Adjustment Seat AdjustmentSeat Adjustment Suspension Seat To Reduce the Speed of the Faster Wheel Speed Balancing AdjustmentNeutral Adjustment Parking Brake Adjustment RETURN-TO-NEUTRAL AdjustmentTo adjust the spring pre-load Suspension AdjustmentBlade Brake Check PTO Clutch AdjustmentTo adjust pedal position Cutting Height AdjustmentFoot Pedal Adjustment Outer Rod . Adjust the Inner & Outer Lift Rods Deck Lift ROD Timing AdjustmentInner Rod Outer RodDeck Lift Spring Deck Leveling AdjustmentHydraulic Pump Drive Belt Replacement Mower PTO Belt 72 Mower Deck Nut Stationary Idler Pulley Mower Belt ReplacementChecking Battery Voltage Battery ServiceCharging a Completely Discharged Battery Jump Starting With Auxiliary Booster BatteryMake Certain Vehicles do not Touch This HOOK-UP for Negative Ground VehiclesEngine DimensionsChassis TransmissionsFerris Limited Warranty Mower Deck Belts and BladesTractor

5900612, 5900613, 5900611, 5900716, 5900752 specifications

Briggs & Stratton is a leading manufacturer of small engines, known for their reliability and performance in a variety of applications. Among their extensive range of products, the model numbers 5900752, 5901184, 5900753, 5900611, and 5900613 represent a collection of essential components designed to enhance engine efficiency and user experience.

The Briggs & Stratton 5900752 is recognized for its high-quality air filter. This filter is engineered to trap dust and dirt effectively, ensuring that only clean air enters the engine. A clean air intake is crucial for optimal performance and longevity of the engine, as it prevents wear and tear on internal components. Its design allows for easy installation and maintenance, making it user-friendly for homeowners and professionals alike.

The 5901184 is a fuel tank assembly designed for enhanced durability and a consistent fuel supply. This component is vital for maintaining stable engine performance, minimizing fuel leakage, and ensuring the integrity of the engine system. The material used in its construction is resistant to corrosion, which is critical for longevity, especially in outdoor equipment exposed to various environmental conditions.

The 5900753 represents a high-performance carburetor that plays a significant role in the mixture of air and fuel. Its precision-engineered design allows for efficient combustion, resulting in robust engine performance. This carburetor is built to handle fluctuations in load, ensuring that the engine runs smoothly under different operating conditions.

The Briggs & Stratton 5900611 and 5900613 series are vital components known for their ignition systems. These components contribute to reliable spark generation, which is essential for engine starting and operation. The enhanced ignition efficiency not only boosts engine starts but also promotes fuel efficiency and reduces emissions, aligning with the growing demand for environmentally conscious products.

Overall, the features and technologies present in the Briggs & Stratton 5900752, 5901184, 5900753, 5900611, and 5900613 highlight the company’s commitment to quality, performance, and user-centered design. With a focus on reliability and ease of use, these components are engineered to meet the needs of various applications, from residential lawn care to commercial landscaping. As part of Briggs & Stratton's extensive catalog, these components are essential for maintaining optimal engine performance and ensuring a seamless user experience in the field.
Top Page Image Contents