Briggs & Stratton 5901184, 5901186, 5901183, 5900717, 5900718 Seat Adjustment Suspension Seat

Page 38

Troubleshooting, Adjustment & Service

SEAT ADJUSTMENT

See Figure 25. The seat can be adjusted forward and back. Move the lever forward, position the seat as desired, and release the lever to lock the seat into position.

SEAT ADJUSTMENT (SUSPENSION SEAT)

See Figure 26. In addition to the forward and backward seat adjustment, models equipped with a suspension seat can be adjusted for lumbar support, suspension and back angle.

Forward and Backward Adjustment:

Move the forward / backward seat adjustment lever (A, Figure 26) away from the seat, position the seat as desired, and release the lever to lock the seat into position.

Lumbar Adjustment:

Turn the lumbar adjustment knob (B) until the desired amount of lumbar is achieved.

Back Angle Adjustment:

Turn the back angle adjustment knob (C) until the desired amount of back angle is achieved.

Suspension Adjustment:

Turn the suspension adjustment knob (D) until the display scale has a reading that matches the weight of the operator.

Seat Adjustment

Lever

Figure 25. Seat Adjustment

B

A

C

D

Troubleshooting

GROUND SPEED CONTROL LEVER ADJUSTMENT

The control levers can be adjusted in three ways. The alignment of the control levers, the placement of the levers (how close the ends are to one another) and the height of the levers can be adjusted.

To Adjust the Handle Alignment

Loosen the mount bolts (A, Figure 27) and pivot the lever(s) (C) to align with each other.

To Adjust the Handle Placement

Loosen the jam nuts and adjust the placement bolt

(B) in or out to properly adjust the lever end spacing.

To Adjust the Handle Height

Remove the mounting hardware and reposition the handle either up or down from its original position. You will need to readjust the handle alignment as described above.

Figure 26. Suspension Seat Adjustment

A.Forward / Backward Seat Adjustment Lever

B.Lumbar Adjustment Knob

C.Back Angle Adjustment Knob

D.Suspension Adjustment Knob

C

B

A

Figure 27. Control Lever Adjustment

A.Alignment Hardware

B.Placement Hardware

C.Ground Speed Control Lever

36

www.ferrisindustries.com

Page 37 Page 39
Image 38
Page 37 Page 39
Contents Model Number Briggs & Stratton Power Products Group, LLC 5100806Description Date Purchased Table of Contents Operating Safety Slope Operation Roll Bar Use Fuel and Maintenance Preparation OperationTraining Children Slope OperationTowed Equipment RIDE-ON Units EmissionsService and Maintenance Ignition System Gasoline ModelsRoll BAR Instructions Operational WarningsInspection and Maintenance of the Roll BAR Seat Belt Identification Numbers Identification TagSafety Decals Operational Safety Checks Safety Interlock SystemNorth American Safety Icons Control Functions Seat Adjustment LeverIgnition Switch Ground Speed LeversWater Temperature Gauge PTO Power Take Off SwitchHour Meter / Maintenance Reminder Throttle ControlGeneral Operating Safety Checks Before StartingPushing the Rider by Hand Starting the EngineStopping the Rider Forward Travel Practice Zero Turn Driving PracticeSmooth Travel Reverse Travel PracticeExecuting Turns Practice Turning Around a Corner Practice Turning In PlaceExecuting an End-Of-Row Zero Turn TurningHeight of Grass MowingMowing Recommendations Tall Grass Requires Incremental CuttingMowing Patterns When and How Often to MowMowing Methods Proper Broadcast MowingAttaching a Trailer Proper MulchingTo raise the roll bar Raise & Lower the Roll BARTo lower the roll bar Keep roll bar in the raised position and use seat beltTemporary Storage 30 Days Or Less StorageStarting After Long Term Storage Long Term Storage Longer Than 30 DaysEngine Maintenance Safety ItemsRider Maintenance Before Every Spring Each 100 250 Fall Use HoursFuel Filter Check Tire PressuresChecking / Adding Fuel Change OIL & FilterChange Interval Every 500 Hours Filter Part Number Check Hydraulic OIL LevelHydraulic OIL Filter Change Pressurized System Change Engine Coolant Clean Radiator & ScreenCheck Engine Coolant Level Oil LubricationGrease ANTI-SCALP Deck Casters Battery MaintenanceCleaning the Battery and Cables Servicing the Mower Blades Removing the BladeRegular Maintenance Troubleshooting Warning Troubleshooting the RiderTroubleshooting the Mower Rider TroubleshootingTroubleshooting Common Cutting Problems StreakingGround Speed Control Lever Adjustment Seat AdjustmentSeat Adjustment Suspension Seat To Reduce the Speed of the Faster Wheel Speed Balancing AdjustmentNeutral Adjustment RETURN-TO-NEUTRAL Adjustment Parking Brake AdjustmentSuspension Adjustment To adjust the spring pre-loadPTO Clutch Adjustment Blade Brake CheckTo adjust pedal position Cutting Height AdjustmentFoot Pedal Adjustment Inner Rod Deck Lift ROD Timing AdjustmentOuter Rod . Adjust the Inner & Outer Lift Rods Outer RodDeck Leveling Adjustment Deck Lift SpringHydraulic Pump Drive Belt Replacement Mower Belt Replacement Mower PTO Belt 72 Mower Deck Nut Stationary Idler PulleyCharging a Completely Discharged Battery Battery ServiceChecking Battery Voltage Jump Starting With Auxiliary Booster BatteryThis HOOK-UP for Negative Ground Vehicles Make Certain Vehicles do not TouchChassis DimensionsEngine TransmissionsFerris Limited Warranty Mower Deck Belts and BladesTractor

5900612, 5900613, 5900611, 5900716, 5900752 specifications

Briggs & Stratton is a leading manufacturer of small engines, known for their reliability and performance in a variety of applications. Among their extensive range of products, the model numbers 5900752, 5901184, 5900753, 5900611, and 5900613 represent a collection of essential components designed to enhance engine efficiency and user experience.

The Briggs & Stratton 5900752 is recognized for its high-quality air filter. This filter is engineered to trap dust and dirt effectively, ensuring that only clean air enters the engine. A clean air intake is crucial for optimal performance and longevity of the engine, as it prevents wear and tear on internal components. Its design allows for easy installation and maintenance, making it user-friendly for homeowners and professionals alike.

The 5901184 is a fuel tank assembly designed for enhanced durability and a consistent fuel supply. This component is vital for maintaining stable engine performance, minimizing fuel leakage, and ensuring the integrity of the engine system. The material used in its construction is resistant to corrosion, which is critical for longevity, especially in outdoor equipment exposed to various environmental conditions.

The 5900753 represents a high-performance carburetor that plays a significant role in the mixture of air and fuel. Its precision-engineered design allows for efficient combustion, resulting in robust engine performance. This carburetor is built to handle fluctuations in load, ensuring that the engine runs smoothly under different operating conditions.

The Briggs & Stratton 5900611 and 5900613 series are vital components known for their ignition systems. These components contribute to reliable spark generation, which is essential for engine starting and operation. The enhanced ignition efficiency not only boosts engine starts but also promotes fuel efficiency and reduces emissions, aligning with the growing demand for environmentally conscious products.

Overall, the features and technologies present in the Briggs & Stratton 5900752, 5901184, 5900753, 5900611, and 5900613 highlight the company’s commitment to quality, performance, and user-centered design. With a focus on reliability and ease of use, these components are engineered to meet the needs of various applications, from residential lawn care to commercial landscaping. As part of Briggs & Stratton's extensive catalog, these components are essential for maintaining optimal engine performance and ensuring a seamless user experience in the field.
Top Page Image Contents