Briggs & Stratton 5900664, 5900692 manual Return-To-Neutral Neutral Adjustment

Page 17

 

S200X 25HP & 27HP - 61” Mower Deck

Return-To-Neutral &

B

C

 

Neutral Adjustment

 

 

 

 

 

 

RETURN-TO-NEUTRAL ADJUSTMENT

 

 

 

To determine if it is necessary to adjust the neutral return,

 

 

 

perform the following steps.

 

A

 

1. Disengage the PTO, engage the parking brake and

 

 

 

D

E

turn off the engine.

 

 

 

2. Move the ground speed control levers into the

 

 

 

operating position, pull levers rearward and release.

 

 

 

3. Move the ground speed control levers out towards the

Figure 33. Neutral Return Spring Adjustment

neutral position. If the levers do not align with the

A. Set Collar

 

 

notches in the neutral lock plate, it is necessary to

B. Adjustment Linkage Rod

 

 

adjust the adjustment linkage rod (B, Figure 33).

C. Neutral Return Spring

 

 

ADJUSTMENT

D. Neutral Return Bushing

 

 

1. Pull the ground speed control lever rearward and

E. Spring Stop Plate

 

 

 

 

 

release to check position. If the ground speed control

 

 

 

lever does not align itself with the notch in the neutral

 

 

 

plate, then move the set collar (A, Figure 33) forward

 

 

 

or back on the adjustment linkage rod (B) until the

 

 

 

ground speed control lever aligns with the notch.

 

 

 

Retighten the set collar.

 

 

 

2. Make sure that the neutral return bushing (D) is

 

 

 

seated correctly in the spring stop plate (E).

 

 

 

3. Pull the ground speed control lever rearward and

 

 

 

release to check position again. Adjust as necessary

 

 

 

to align the ground speed control levers with the

 

 

 

notches in the neutral lock plate.

 

 

 

It is important to note that after every adjustment of the

 

 

 

adjustment linkage rod, the lever must be pulled rearward

 

 

 

and released to properly check the neutral position.

 

 

 

NEUTRAL ADJUSTMENT

 

 

 

If the tractor “creeps” while the ground speed control

A

 

 

levers are locked in NEUTRAL, than it may be necessary

 

 

 

 

 

to adjust the linkage rod.

B

 

 

 

 

 

NOTE: Perform this adjustment on a hard, level surface

 

 

 

such as a concrete floor.

 

 

 

1. Disengage the PTO, engage the parking brake and

 

 

 

turn off the engine.

 

 

 

2. There are three nuts (B, Figure 34) on the linkage rod.

Figure 34. Neutral Adjustment

 

 

The first two are to be used together to turn the rod

 

 

and the third (towards the front of the machine) is

(Left side shown)

 

 

used to lock the rod in place. Loosen the jam nut that

A. Adjustment Linkage Rod

 

 

locks against the ball joint (B) and turn the linkage rod

B. Nuts

 

 

(A) to adjust. If the machine creeps forward, turn the rod CLOCKWISE (while standing at the rear of the machine, facing forward), if the machine creeps backward, turn the rod COUNTER-CLOCKWISE.

3.Lock the jam nut (B) against the ball joint when neutral is achieved.

NOTE: This adjustment should not be performed while the machine is running. It may take several attempts to achieved neutral, depending upon how much the machine creeps.

7/2007

17

TP 300-7333-02-M2-SP

Page 16 Page 18
Image 17
Page 16 Page 18
Contents Dealer Setup Adjustment Instructions S200X 25HP & 27HP 61 Mower Deck Quick Setup ListConnect Battery Battery InstallationUncrating Hydraulic Release ValveSeat Assembly Tractor AssemblyMotion Control Handle Assembly Install the Roll Bar Roll Bar InstallationCheck Tire Pressures Check Fluid LevelsCheck the Engine Oil Level Check the Hydraulic Oil Level Tire PressureInstall Deck Pusher Bars 72 Models Check the Mower AssemblyCheck Torque Mower Blades Bolts to 70 ft.lbs N.mDeck Hanger Chain Installation Install the Mower Deck 72 ModelsCheck Lift Rod Timing Check Deck Rod TimingDeck Leveling Adjustment Mower PTO Belt 61 Models Idler Arm Stationary Idler Pulley Check Deck Drive BeltGrease LubricationOil Lubricating the Front CastersStarting The Engine Adding FuelTo add fuel Adding FuelFunctional Tests Perform Safety ChecksSeat Adjustment Suspension Seat Seat AdjustmentMotion Control Handle Adjustment Return-To-Neutral Neutral Adjustment Parking Brake Adjustment Brake Spring Adjustment Nut Parking Brake Adjustment

5900664, 5900692 specifications

Briggs & Stratton has long been a trusted name in the engine industry, renowned for its innovation and performance. Among its wide array of products, the Briggs & Stratton 5900692 and 5900664 models stand out, featuring a range of characteristics that cater to the needs of both professionals and enthusiasts alike.

The Briggs & Stratton 5900692, also known as a fuel tank assembly and cap, is designed to provide a reliable and effective solution for fuel storage in lawn and garden equipment. One of its main features is its durable construction, which ensures longevity and resistance to environmental factors. Made from high-quality materials, it is impervious to the types of wear and tear commonly encountered in outdoor usage, ensuring that it remains functional over time.

On the other hand, the Briggs & Stratton 5900664 is a carburetor specifically engineered for certain small engines. An impressive feature of this model is its efficient fuel delivery system. The carburetor plays a crucial role in maintaining optimal engine performance by precisely mixing air and fuel in the correct proportions. This leads to improved fuel efficiency, lower emissions, and enhanced power output, making it an excellent addition to any compatible engine setup.

Both models embody advanced engineering technologies that highlight Briggs & Stratton's commitment to quality and innovation. The fuel tank assembly employs a secure locking mechanism that prevents fuel leakage and enhances safety during operation. Meanwhile, the carburetor features adjustable settings, providing users the ability to fine-tune their engines for specific applications, whether it be for mowing, tilling, or other tasks requiring dependable performance.

In addition to their specific functions, both the 5900692 and 5900664 are designed for straightforward installation and compatibility with a range of equipment, minimizing downtime and allowing users to get back to work quickly. Their reliability under heavy loads and in various environmental conditions further emphasizes the reputation of Briggs & Stratton as a leader in small engine technology.

Ultimately, the Briggs & Stratton 5900692 and 5900664 models exemplify the company's dedication to producing high-performance, durable solutions for lawn and garden care. Whether you require an effective fuel storage solution or a precise carburetion system, these models deliver the quality and functionality that professionals and DIYers expect from Briggs & Stratton.
Top Page Image Contents