Alamo T 7740 manual Information Bulletin 120697 from previous, Electrical connection, To Valve

Page 37

Information Bulletin 120697 Continued from previous Page

Electrical connection:

Identify the plus (+) lead running to the solenoid for the tilt function. This solenoid is located across the valve from the fitting you installed. Remove approximately 2 " of the outer plastic covering from the wires coming from the solenoid. Splice one of the 18 gauge wires you provided into one of the wires. Connect the other end of that wire to a lug on the solenoid. It makes a difference which wire runs to which connector. Insulate any exposed wires with electrical tape.

Note orientation of notch in plate

To Valve

Very Important ! DO NOT use

Solenoids as handles

"C-1"	"C-2"
Port	Port

Wire connector Lugs

Door

Tilt

Dipper

Lift

Swing

Steps to take to install the tilt cylinder lock valve

Hydraulic Connections

1.Remove the tilt section hose from the "C-1" Port

2.Assemble the parts as shown above.

3.Attach the hose to the fitting on Lock valve, Test and run.

TECHNICAL INFORMATION BULLETIN

No. 120697

This document does not authorize the repair or replacement of parts under warranty

MACHETE

© 2005 Alamo Group Inc.

1-31

Image 37

Contents Edition Information Service BulletinsPage Information & Service Bulletins Introduction Index Machete Section Service Bulletins Alamo Group Inc Section Subject Pulley Fastening to Cutter Shaft of Flail Axe HeadMachete Models Failures of the mower push-pull switchInformation Bulletin 092895 from previous Technical Information BulletinParts Needed Welding ProcedureInformation Bulletin 121495 from previous Corrective Action New Parts Old Parts New Piston Pump used on MacheteNew Seal Protector Added to Blade Bar Assembly Information Bulletin 032596 from previous Oil Leaking from new single Acting Hydraulic Cylinders Dead Batteries on New tractors Cracks in Main Frame Information Bulletin 010397 from previous Interference between Tube Clamps and Main Frame Valve Block O-Ring Replacement Kit available King Pin and Boom Pin Bushing Drivers Available Machete Hitch Post Replacement Kits Hitch Post Replacement KitsRepair Procedures Flanges to prevent rust Information Bulletin 041797-1 from previousKit Numbers Cylinder & Linkage Pin Replacement KitsInformation Bulletin 041797-2 from previous Tilt Link Arm Stop New Thick Blade Bar & Larger Bolts Procedure Joystick Power Cut Off SwitchParts needed Parts Required Cylinder, Link Arm, Turning Arm & Hitch Post Pin Update KitUpdate Kits Combined Kit P/N Machete Following parts are required to make this modification Lock Valve Installation InstructionsElectrical connection Information Bulletin 120697 from previousTo Valve Eleminate Erratic Boom movement Part Numbers required Hood to Frame Interference on TS Series TractorsNew Holland TS Series Fuel Filter New Oil Filter Kit P/N Spindle Oil Filler Kit P/N When to Change Filter Filter Maintenance ProcedureElement Service Procedure Control Valve Relocation Change in the availability of rebuilt components Filter Kit to Update Control Valve System Kit P/N Filter Maintenance Procedure Buzz Bar Drive Coupling Design change Conversion Spindle Bearing Lubrication UpdateRecommended Brands of Hydraulic Oil Effective February 18 Warranty RepairsFactory Spoke Cast Pulley Information Bulletin 041503 from previous Recommended Tools Installation ProcedureProtection of Lexan Sheets Information Bulletin 102103 from previous KIts Available Driveline Update KitPulley Spacer Information Bulletin 011304 from previousMachete Service Bulletins Service Required Joystick ReplacementParts Labor Old Parts Disposition Termination Date Motor to Spindle Bolt Replacement King Post Pin Replacement Longer Pins Machete Rear Flap Bracket, Machete Rotary Head Service Bulletin 962503-1 from previous Service BulletinLower Crossmember Kit Installation Frame Rail Reinforcement, LH Frame Rail Joystick Control of Boom Movement Restrictor Installation Tilt Cylinder Function Parts Required Turning Arm King Pin Replacement Kits Turning Arm King Pin UpgradesNext Service Bulletin 971903 from previous Boom Hinge Point Pin Upgrades Service Bulletin 972103 from previous Restrictor Installation Lift & Dipper Cylinder Function Upper King Pin Bushing Slipping Blade Bolt Inspection / Recall Lower Cross Member Reinforcement Kit P/N Units Serial Numbers Model T New Holland T7740 & T6640 A/C Drier CampaignModel T6640 Special NoteUnits Serial Numbers New Holland TS Tractor Inspection CampaignTurning Arm Pin Update Kit P/N Service Bulletin 991012 from previous Repair Plates Dipper Boom Reinforcement PlatesValve Pressure Filter Kit Buzz Bar Head Motor Coupler Re-Design Buzz Bar Head Motor Coupler Coupler Update Kit Blade Bolt Inspection Blade Carrier Retaining Bolts 222Service Instructions Port Plug Update SubjectAll Brahmas Parts RequiredPage Alamo Group Inc