Alamo T 7740 manual Spindle Oil Filler Kit P/N

Page 42

TECHNICAL INFORMATION BULLETIN No. 080300

Alamo Industrial ™ Technical Services Department

1502 East Walnut

Seguin, Texas 78155

830-372-2708

Models: All Machete, A-Boom, Versa, Rear Mount, Slopemower, Brahma, EKII, Hydro 60, Hydro 72 & Hydro 15

All Hydraulic powered Rotary Mower heads that utilize the

# 02960553B, 02960553C and 02968859A Spindle Assemblies.

Bulletin No:

080300

Date:

Aug. 3, 2000

Spindle Oil Filler Kit P/N 02976501:

A Spindle oil filler kit has been developed to provide accurate an easy fill of oil into the spindles used on all hydraulic powered mowers. The Oil filler Kit P/N 02976501 is available through Alamo Industrial Parts dept.

Installation requires the replacement of the fill plug with the female quick connect fitting. To fill the spindle. attach the hose and oil bottle to the spindle by utilizing the quick connect fittings. remove the vent plug and pump in the oil untill oil is seen at the vent plug opening. reinstall the vent plug and remove the bottle at the quick connect fitting. The female quick disconnect is designed to be left on the spindle in place of the fill plug.

Utilization of this spindle fill kit should decrease maintance time and failures by providing accurate oil fill of the spindle assembly.

Hose (with clamp)

Female Quick Connect

Spindle Assembly

Vent

Figure 1

Fill Plug (Removed)

Oil tank

(with Hand Pump)

This document does not authorize the repair or replacement of parts under warranty

MACHETE

© 2005 Alamo Group Inc.

1-36

Image 42

Contents Information Service Bulletins EditionPage Information & Service Bulletins Introduction Index Machete Section Service Bulletins Alamo Group Inc Section Pulley Fastening to Cutter Shaft of Flail Axe Head SubjectMachete Failures of the mower push-pull switch ModelsTechnical Information Bulletin Information Bulletin 092895 from previousWelding Procedure Parts NeededInformation Bulletin 121495 from previous Corrective Action New Piston Pump used on Machete New Parts Old PartsNew Seal Protector Added to Blade Bar Assembly Information Bulletin 032596 from previous Oil Leaking from new single Acting Hydraulic Cylinders Dead Batteries on New tractors Cracks in Main Frame Information Bulletin 010397 from previous Interference between Tube Clamps and Main Frame Valve Block O-Ring Replacement Kit available King Pin and Boom Pin Bushing Drivers Available Machete Hitch Post Replacement Kits Hitch Post Replacement KitsRepair Procedures Information Bulletin 041797-1 from previous Flanges to prevent rustCylinder & Linkage Pin Replacement Kits Kit NumbersInformation Bulletin 041797-2 from previous Tilt Link Arm Stop New Thick Blade Bar & Larger Bolts Joystick Power Cut Off Switch ProcedureParts needed Cylinder, Link Arm, Turning Arm & Hitch Post Pin Update Kit Parts RequiredUpdate Kits Combined Kit P/N Machete Lock Valve Installation Instructions Following parts are required to make this modificationInformation Bulletin 120697 from previous Electrical connectionTo Valve Eleminate Erratic Boom movement Hood to Frame Interference on TS Series Tractors Part Numbers requiredNew Holland TS Series Fuel Filter New Oil Filter Kit P/N Spindle Oil Filler Kit P/N Filter Maintenance Procedure When to Change FilterElement Service Procedure Control Valve Relocation Change in the availability of rebuilt components Filter Kit to Update Control Valve System Kit P/N Filter Maintenance Procedure Buzz Bar Drive Coupling Design change Spindle Bearing Lubrication Update ConversionRecommended Brands of Hydraulic Oil Warranty Repairs Effective February 18Factory Spoke Cast Pulley Information Bulletin 041503 from previous Installation Procedure Recommended ToolsProtection of Lexan Sheets Information Bulletin 102103 from previous Driveline Update Kit KIts AvailableInformation Bulletin 011304 from previous Pulley SpacerMachete Service Bulletins Joystick Replacement Service RequiredParts Labor Old Parts Disposition Termination Date Motor to Spindle Bolt Replacement King Post Pin Replacement Longer Pins Machete Rear Flap Bracket, Machete Rotary Head Service Bulletin Service Bulletin 962503-1 from previousLower Crossmember Kit Installation Frame Rail Reinforcement, LH Frame Rail Joystick Control of Boom Movement Restrictor Installation Tilt Cylinder Function Turning Arm King Pin Upgrades Parts Required Turning Arm King Pin Replacement KitsNext Service Bulletin 971903 from previous Boom Hinge Point Pin Upgrades Service Bulletin 972103 from previous Restrictor Installation Lift & Dipper Cylinder Function Upper King Pin Bushing Slipping Blade Bolt Inspection / Recall Lower Cross Member Reinforcement Kit P/N Model T6640 New Holland T7740 & T6640 A/C Drier CampaignUnits Serial Numbers Model T Special NoteNew Holland TS Tractor Inspection Campaign Units Serial NumbersTurning Arm Pin Update Kit P/N Service Bulletin 991012 from previous Dipper Boom Reinforcement Plates Repair PlatesValve Pressure Filter Kit Buzz Bar Head Motor Coupler Re-Design Buzz Bar Head Motor Coupler Coupler Update Kit Blade Bolt Inspection 222 Blade Carrier Retaining BoltsAll Brahmas Port Plug Update SubjectService Instructions Parts RequiredPage Alamo Group Inc