Alamo T 7740 manual Change in the availability of rebuilt components

Page 45

TECHNICAL INFORMATION BULLETIN No. 040901

Alamo Industrial ™ Technical Services Department

1502 East Walnut

Seguin, Texas 78155

830-372-2708

Models: All Alamo Industrial Products are affected.

Bulletin No:

040901

Date:

Apr. 9, 2001

Change in the availability of rebuilt components:

This bulletin has been published to inform you of a change in the availability of rebuilt parts. In the past, rebuilt components such as pumps and motors were available for use as spare parts. That will no longer be the case. The major factor in this decision was the lack of cores that are returned from the customer.

Since Alamo Industrial will no longer offer rebuilt parts an effort will be made to offer customers a complete parts listing of all components that are needed as service repairs. The most common service parts are pumps and motors will now be available for order through Alamo Industrial Customer Service Department. Likewise, a parts breakdown with Alamo Industrial part numbers will be provided. The Eaton Pumps and Motors, Danfoss Control Valves will be the first components available with such a parts breakdown.

It is Our intention to provide a better and more reliable service parts system. This transition will better suit customer, and provide more timely and efficient parts delivery.

This document does not authorize the repair or replacement of parts under warranty

MACHETE

© 2005 Alamo Group Inc.

1-39

Image 45
Contents Edition Information Service BulletinsPage Information & Service Bulletins Introduction Index Machete Section Service Bulletins Alamo Group Inc Section Subject Pulley Fastening to Cutter Shaft of Flail Axe HeadMachete Models Failures of the mower push-pull switchInformation Bulletin 092895 from previous Technical Information BulletinParts Needed Welding ProcedureInformation Bulletin 121495 from previous Corrective Action New Parts Old Parts New Piston Pump used on MacheteNew Seal Protector Added to Blade Bar Assembly Information Bulletin 032596 from previous Oil Leaking from new single Acting Hydraulic Cylinders Dead Batteries on New tractors Cracks in Main Frame Information Bulletin 010397 from previous Interference between Tube Clamps and Main Frame Valve Block O-Ring Replacement Kit available King Pin and Boom Pin Bushing Drivers Available Machete Hitch Post Replacement Kits Hitch Post Replacement KitsRepair Procedures Flanges to prevent rust Information Bulletin 041797-1 from previousKit Numbers Cylinder & Linkage Pin Replacement KitsInformation Bulletin 041797-2 from previous Tilt Link Arm Stop New Thick Blade Bar & Larger Bolts Joystick Power Cut Off Switch ProcedureParts needed Parts Required Cylinder, Link Arm, Turning Arm & Hitch Post Pin Update KitUpdate Kits Combined Kit P/N Machete Following parts are required to make this modification Lock Valve Installation InstructionsInformation Bulletin 120697 from previous Electrical connectionTo Valve Eleminate Erratic Boom movement Part Numbers required Hood to Frame Interference on TS Series TractorsNew Holland TS Series Fuel Filter New Oil Filter Kit P/N Spindle Oil Filler Kit P/N Filter Maintenance Procedure When to Change FilterElement Service Procedure Control Valve Relocation Change in the availability of rebuilt components Filter Kit to Update Control Valve System Kit P/N Filter Maintenance Procedure Buzz Bar Drive Coupling Design change Conversion Spindle Bearing Lubrication UpdateRecommended Brands of Hydraulic Oil Effective February 18 Warranty RepairsFactory Spoke Cast Pulley Information Bulletin 041503 from previous Installation Procedure Recommended ToolsProtection of Lexan Sheets Information Bulletin 102103 from previous KIts Available Driveline Update KitPulley Spacer Information Bulletin 011304 from previousMachete Service Bulletins Joystick Replacement Service RequiredParts Labor Old Parts Disposition Termination Date Motor to Spindle Bolt Replacement King Post Pin Replacement Longer Pins Machete Rear Flap Bracket, Machete Rotary Head Service Bulletin 962503-1 from previous Service BulletinLower Crossmember Kit Installation Frame Rail Reinforcement, LH Frame Rail Joystick Control of Boom Movement Restrictor Installation Tilt Cylinder Function Turning Arm King Pin Upgrades Parts Required Turning Arm King Pin Replacement KitsNext Service Bulletin 971903 from previous Boom Hinge Point Pin Upgrades Service Bulletin 972103 from previous Restrictor Installation Lift & Dipper Cylinder Function Upper King Pin Bushing Slipping Blade Bolt Inspection / Recall Lower Cross Member Reinforcement Kit P/N Units Serial Numbers Model T New Holland T7740 & T6640 A/C Drier CampaignModel T6640 Special NoteUnits Serial Numbers New Holland TS Tractor Inspection CampaignTurning Arm Pin Update Kit P/N Service Bulletin 991012 from previous Repair Plates Dipper Boom Reinforcement PlatesValve Pressure Filter Kit Buzz Bar Head Motor Coupler Re-Design Buzz Bar Head Motor Coupler Coupler Update Kit Blade Bolt Inspection Blade Carrier Retaining Bolts 222Service Instructions Port Plug Update SubjectAll Brahmas Parts RequiredPage Alamo Group Inc